Open Access Article
Youssef Harb†‡
a,
Charbel Anthony El Hachem‡
b,
Amale Mcheik
a,
Ghada El Zakhem Naous
a and
Nathalie Hayeck
*a
aDepartment of Physical Sciences, Lebanese American University, Chouran, Beirut 1102-2801, Lebanon. E-mail: Nathalie.hayeck@lau.edu.lb; Tel: +961 1 786456 Ext. 3412
bDepartment of Biological Sciences, Lebanese American University, Chouran, Beirut 1102-2801, Lebanon
First published on 1st May 2026
Per- and polyfluoroalkyl substances (PFAS) are persistent, emerging environmental contaminants with diverse chemical properties and widespread industrial and consumer uses. They are used as key components in products like surfactants, lubricants, fire-fighting foams, non-stick cookware, and water-repellent coatings. Additionally, their volatility and stability enable global transport, often reaching pristine environments across various regions. This review thoroughly examines the global literature on atmospheric PFAS, focusing on their distribution in polar, midlatitude, and tropical areas, the role and mechanisms of wet deposition in their atmospheric behavior, and their chemical transformation and phase partitioning in the atmosphere. While midlatitude industrial and consumer activities are primary sources, PFAS are transported globally. Moreover, wet deposition acts as a sink for atmospheric PFAS, with snow and sea spray especially effective at scavenging long-chain PFAS. Although secondary emissions through re-volatilization could occur, the main factors governing the fate of atmospheric PFAS are precursor transformations and phase partitioning. Volatile PFAS degrade in the atmosphere into more persistent and less volatile forms via oxidative and photochemical processes. The partitioning of PFAS between gas and particulate phases depends on functionalization and chain length, with some studies also emphasizing the role of meteorological conditions. Although this review covers a broad range of regions and environments, the existing literature remains limited, especially in areas such as the Antarctic Peninsula, the Middle East, Africa, and Latin America, where data gaps persist. Future research should focus on monitoring PFAS levels in these underrepresented regions and on enhancing the fundamental and mechanistic understanding of PFAS transformation pathways. Meanwhile, policymakers should prioritize implementing stricter emission controls, reforming regulations on legacy and precursor PFAS, and harmonizing PFAS regulations worldwide.
Environmental significanceThis review highlights the urgent need to address the widespread contamination of per- and polyfluoroalkyl substances (PFAS), commonly referred to as “forever chemicals”, which pose significant risks to ecosystems and human health due to their persistence and bioaccumulation. It highlights how industrial and consumer activities in midlatitude regions contribute substantially to PFAS emissions, which can reach remote areas, including pristine environments like the Arctic, through complex atmospheric processes and wet deposition. The findings underscore the need for stronger regulatory frameworks and enhanced monitoring, particularly in underrepresented regions, to better understand PFAS transport and mitigate their long-term effects. Addressing PFAS contamination is critical for safeguarding biodiversity, ecosystem integrity, and public health, necessitating urgent international collaboration. |
In 2018, the Organization for Economic Cooperation and Development (OECD) established a more precise and unified definition of PFAS in regulatory discussions.3 The definition involved considering a substance to be PFAS if it contains at least one of the following molecular structures: –CnF2n– (n ≥ 3) or –CnF2nOCmF2m– (n, m ≥ 1)3. The former encompasses a fully fluorinated, known as polyfluorinated, carbon chain with at least three carbon atoms, and the latter involves a perfluorinated ether group with oxygen acting as a linker between the fluorinated carbon groups.3 However, the OECD expanded this definition in 2021 by widening the scope of PFAS classification to include short-chain PFAS.4 Moreover, in 2022, the United States Environmental Protection Agency (US EPA) modified a previously proposed definition that limited PFAS to compounds with at least two carbon atoms, one completely and another partially fluorinated.5 This adjustment involved a broader definition that includes fluorocarbons with branched chains and fluoroethers.5
To facilitate discussion of atmospheric fate and transport, Table 1 lists representative PFAS compounds along with their nomenclature, CAS numbers, chain lengths, and classifications. PFAS could be categorized into two main categories: long-chain (LC) and short-chain (SC) compounds, which contain at least eight and fewer than eight carbon atoms, respectively.6 However, the OECD provides a more detailed categorization, defining long-chain PFAS as perfluoroalkyl carboxylic acids (PFCAs) with more than seven carbons, perfluoroalkyl sulfonic acids (PFSAs) with more than six carbons, and substances that can degrade into long-chain PFCAs and PFSAs,7 such as perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS).
| Common name | IUPAC name | Acronym | CAS number | Carbon chain length | Classification |
|---|---|---|---|---|---|
| a On each side. | |||||
| Trifluoroacetic acid | 2,2,2-Trifluoroacetic acid | TFA | 76-05-1 | 2 | Ultrashort chain |
| Perfluoropropanoic acid | 2,3,3,3-Tetrafluoropropanoic acid | PFPrA | 359-49-9 | 3 | Ultrashort chain |
| Perfluoropropanesulfonic acid | 1,1,2,2,3,3,3-Heptafluoropropane-1-sulfonic acid | PFPrS | 423-41-6 | 3 | Ultrashort chain |
| Perfluorobutanoic acid | 2,3,3,4,4,4-Hexafluorobutanoic acid | PFBA | 62765-25-7 | 4 | Short chain |
| Perfluorobutanesulfonic acid | 1,1,2,2,3,3,4,4,4-Nonafluorobutane-1-sulfonic acid | PFBS | 375-73-5 | 4 | Short chain |
| Perfluoropentanoic acid | 2,2,3,4,4,5,5,5-Octafluoro-3-(trifluoromethyl)pentanoic acid | PFPeA | 64139-66-8 | 5 | Short chain |
| Perfluoropentanesulfonic acid | 1,1,2,2,3,3,4,4,5,5,5-Undecafluoropentane-1-sulfonic acid | PFPeS | 2706-91-4 | 5 | Short chain |
| Perfluorohexanoic acid | 2,2,3,3,4,4,5,6,6,6-Decafluoro-5-(trifluoromethyl)hexanoic acid | PFHxA | 15899-29-3 | 6 | Short chain |
| Perfluorohexanesulfonic acid | 1,1,2,2,3,3,4,4,5,5,6,6,6-Tridecafluorohexane-1-sulfonic acid | PFHxS | 355-46-4 | 6 | Short chain |
| 2-(Perfluorobutyl)ethanol | 3,3,4,4,5,5,6,6,6-Nonafluorohexan-1-ol | 4 : 2 FTOH |
2043-47-2 | 6 | Short chain |
| Hexafluoropropylene oxide-dimer acid | 2,3,3,3-Tetrafluoro-2-(1,1,2,2,3,3,3-heptafluoropropoxy)propanoate | HFPO-DA (GenX) | 122499-17-6 | 6 | Short chain |
| Perfluorooctanoic acid | 2,2,3,3,4,4,5,5,6,6,7,7,8,8,8-Pentadecafluorooctanoic acid | PFOA | 335-67-1 | 8 | Long chain |
| Perfluorooctane sulfonate | 1,1,2,2,3,3,4,4,5,5,6,6,7,7,8,8,8-Heptadecafluorooctane-1-sulfonate | PFOS | 45298-90-6 | 8 | Long chain |
| Perfluorooctanesulfonamide | 1,1,2,2,3,3,4,4,5,5,6,6,7,7,8,8,8-Heptadecafluorooctane-1-sulfonamide | PFOSA | 754-91-6 | 8 | Long chain |
| N-Methylperfluorooctanesulfonamide | 1,1,2,2,3,3,4,4,5,5,6,6,7,7,8,8,8-Heptadecafluoro-N-methyl-1-octanesulfonamide | MeFOSA | 31506-32-8 | 8 | Long chain |
| N-Ethylperfluorooctanesulfonamide | N-Ethyl-1,1,2,2,3,3,4,4,5,5,6,6,7,7,8,8,8-heptadecafluoro-1-octanesulfonamide | EtFOSA | 4151-50-2 | 8 | Long chain |
| N-Methylperfluorooctanesulfonamidoethanol | 1,1,2,2,3,3,4,4,5,5,6,6,7,7,8,8,8-Heptadecafluoro-N-(2-hydroxyethyl)-N-methyloctane-1-sulfonamide | MeFOSE | 24448-09-7 | 8 | Long chain |
| N-Ethylperfluorooctanesulfonamidoethanol | N-Ethyl-1,1,2,2,3,3,4,4,5,5,6,6,7,7,8,8,8-heptadecafluoro-N-(2-hydroxyethyl)octane-1-sulfonamide | EtFOSE | 1691-99-2 | 8 | Long chain |
| 2-(Perfluorohexyl)ethanol | 3,3,4,4,5,5,6,6,7,7,8,8,8-Tridecafluorooctan-1-ol | 6 : 2 FTOH |
647-42-7 | 8 | Long chain |
| 2-(Perfluorohexyl)ethyl acrylate | 3,3,4,4,5,5,6,6,7,7,8,8,8-Tridecafluorooctyl prop-2-enoate | 6 : 2 FTAC |
17527-29-6 | 8 | Long chain |
| 2-(Perfluorohexyl)ethane-1-sulfonic acid | 3,3,4,4,5,5,6,6,7,7,8,8,8-Tridecafluorooctane-1-sulfonic acid | 6 : 2 FTSA |
27619-97-2 | 8 | Long chain |
| Mono[2-(perfluorohexyl)ethyl] phosphate | 3,3,4,4,5,5,6,6,7,7,8,8,8-Tridecafluorooctyl dihydrogen phosphate | 6 : 2 MonoPAP |
57678-01-0 | 8 | Long chain |
| Bis[2-(perfluorohexyl)ethyl]phosphate | bis(3,3,4,4,5,5,6,6,7,7,8,8,8-Tridecafluorooctyl) hydrogen phosphate | 6 : 2 DiPAP |
57677-95-9 | 8a | Long chain |
| 2-(Perfluorohexyl)ethyl methacrylate | 3,3,4,4,5,5,6,6,7,7,8,8,8-Tridecafluorooctyl 2-methylprop-2-enoate | 6 : 2 FTMAC |
2144-53-8 | 8 | Long chain |
| Perfluorononanoic acid | 2,2,3,3,4,4,5,5,6,6,7,7,8,8,9,9,9-Heptadecafluorononanoic acid | PFNA | 375-95-1 | 9 | Long chain |
| Perfluorodecanoic acid | 2,2,3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10,10-Nonadecafluorodecanoic acid | PFDA | 335-76-2 | 10 | Long chain |
| 2-(Perfluorooctyl)ethanol | 3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10,10-Heptadecafluorodecan-1-ol | 8 : 2 FTOH |
678-39-7 | 10 | Long chain |
| 2-(Perfluorooctyl)ethyl acrylate | 3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10,10-Heptadecafluorodecyl prop-2-enoate | 8 : 2 FTAC |
27905-45-9 | 10 | Long chain |
| Mono[2-(perfluorooctyl)ethyl] phosphate | 3,3,4,4,5,5,6,6,7,7,8,8,8-Tridecafluorooctyl dihydrogen phosphate | 8 : 2 MonoPAP |
57678-03-2 | 10 | Long chain |
| Bis[2-(perfluorooctyl)ethyl] phosphate | bis(3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10,10-Heptadecafluorodecyl) hydrogen phosphate | 8 : 2 DiPAP |
678-41-1 | 10 | Long chain |
| 2-(Perfluorooctyl)ethyl methacrylate | 3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10,10-Heptadecafluorodecyl 2-methylprop-2-enoate | 8 : 2 FTMAC |
1996-88-9 | 10 | Long chain |
| Perfluoroundecanoic acid | 2,2,3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10,11,11,11-Henicosafluoroundecanoic acid | PFUnDA | 2058-94-8 | 11 | Long chain |
| Perfluorododecanoic acid | 2,2,3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10,11,11,12,12,12-Tricosafluorododecanoic acid | PFDoDA | 307-55-1 | 12 | Long chain |
| 2-(Perfluorodecyl)ethanol | 3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10,11,11,12,12,12-Henicosafluorododecan-1-ol | 10 : 2 FTOH |
865-86-1 | 12 | Long chain |
| 2-(Perfluorodecyl)ethyl acrylate | 3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10,11,11,12,12,12-Henicosafluorododecyl prop-2-enoate | 10 : 2 FTAC |
17741-60-5 | 12 | Long chain |
| 2-(Perfluorodecyl)ethyl methacrylate | 3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10,11,11,12,12,12-Henicosafluorododecyl 2-methylprop-2-enoate | 10 : 2 FTMAC |
2144-54-9 | 12 | Long chain |
| Perfluorotridecanoic acid | 2,2,3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10,11,11,12,12,13,13,13-Pentacosafluorotridecanoic acid | PFTrDA | 72629-94-8 | 13 | Long chain |
| Perfluorotetradecanoic acid | 2,2,3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10,11,11,12,12,13,13,14,14,14-Heptacosafluorotetradecanoic acid | PFTeDA | 376-06-7 | 14 | Long chain |
| Perfluoropentadecanoic acid | 2,2,3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10,11,11,12,12,13,13,14,14,15,15,15-Nonacosafluoropentadecanoic acid | PFPeDA | 141074-63-7 | 15 | Long chain |
While PFOA and PFOS are the most recognized long-chain PFAS, the broader category includes other compounds like perfluorononanoic acid (PFNA) and perfluorodecanoic acid (PFDA), which also possess persistent properties that make them physiologically harmful.8 Other long-chain PFCAs include perfluoroundecanoic acid (PFUnDA), perfluorododecanoic acid (PFDoDA), perfluorotridecanoic acid (PFTrDA), perfluorotetradecanoic acid (PFTeDA), and perfluoropentadecanoic acid (PFPeDA).9 Moreover, some PFCA precursors include fluorotelomer alcohols (FTOHs),10 fluorotelomer acrylates (FTACs)10 and methacrylates (FTMs),10 fluorotelomer sulfonates (FTSAs)11 and polyfluoroalkyl phosphate esters (PAPs and diPAPs).11 Additionally, some perfluoroalkane sulfonamides (PFASAs), precursors for PFSAs, were detected in environmental and biological matrices, including perfluorooctanesulfonamide (PFOSA), N-methylperfluorooctanesulfonamide (MeFOSA), N-ethylperfluorooctanesulfonamide (EtFOSA), N-methylperfluorooctanesulfonamidoethanol (MeFOSE), N-ethylperfluorooctanesulfonamidoethanol (EtFOSE).12 Perfluorohexanoic acid (PFHxA) and perfluorohexanesulfonic acid (PFHxS) have also been heavily discussed in the literature due to their serious toxicological effects.13
Short-chain PFAS usually refer to compounds containing between four and six carbon atoms, while ultrashort-chain PFAS include those with one and three carbon atoms.14 Short-chain and ultrashort-chain PFAS molecules have been poorly studied in the literature due to multiple challenges. Those challenges encompass their limited scope of analysis due to their high polarity and the perception that they are less harmful, less persistent, and less accumulative than their long-chain counterparts.14 However, some studies have shown that exposure to short and ultrashort-chain PFAS appears to have multiple adverse effects on reproductive, developmental, hepatic, and renal health.15–17 Moreover, short-chain PFAS have historically received less regulatory attention compared to the longer chain ones.14 In general terms, short-chain PFAS include perfluorobutanoic acid (PFBA), perfluoropentanoic acid (PFPeA), perfluorobutanesulfonic acid (PFBS), and perfluoropentanesulfonic acid (PFPeS), whereas ultrashort-chain PFAS include trifluoroacetic acid (TFA), perfluoropropanoic acid (PFPrA) and perfluoropropanesulfonic acid (PFPrS).18 The global fate and transport of ultrashort- and short-chain PFAS remain poorly understood, with two main hypotheses proposed in the literature regarding their movement in the environment.14 The first hypothesis proposes that marine aerosols are the primary mode of transport of ionic PFAS,19 whereas the second hypothesis suggests that volatile PFAS precursors are transported to remote regions and contaminate the environment with short-chain PFAS through degradation mechanisms.20
PFAS are synthetic chemical substances extensively employed since the mid-20th century in a wide variety of industrial processes and consumer products due to their physicochemical properties, including exceptional stability, hydrophobicity, lipophobicity, and heat resistance. The widespread use of PFAS stems primarily from their role as critical components in surfactants, lubricants, water- and stain-repellent coatings, and fire-fighting foams. Major industrial sources include primary manufacturing facilities, where a wide variety of PFAS are released into the environment. For example, fluoropolymer manufacturing plants emit PFAS, such as multi-head perfluoroalkyl ether sulfonates (PFESs), into the air, soil, and water. Studies have shown that both gas-phase and particle-phase PFAS are present in high concentrations inside and outside FMFs. These emissions can travel significant distances, especially short-chain PFAS, which are particularly mobile.21,22
Once airborne, PFAS can exist in both gas and particle-bound forms. Neutral compounds such as FTOHs and PFOSAs are found in higher concentrations in the atmosphere than ionic PFAS.23 Wastewater treatment plants (WWTP) have also been shown to be critical PFAS sources in the atmosphere throughout various mechanisms, particularly PFAS present in water can volatilize during aeration and other possible treatments, as air samples collected over WWTP showed high levels of FTOHs and conversely low concentrations of PFOSAs derivatives.24,25 PFAS were also detected in regions where all of the previous sources are not present, indicating long-range atmospheric transport (LRAT), where PFAS molecules travel long distances in the atmosphere.26 In brief, the widespread and persistent presence of PFAS in the atmosphere results from several overlapping emission sources, ranging from industrial manufacturing and wastewater treatment plants as the major contributors, to consumer product usage and degradation. Their chemical stability and volatility, particularly for neutral PFAS such as FTOHs and PFOSAs, permit them to persist in the environment and be transported to remote ecosystems such as the Amazon and the Arctic. Moreover, textile and metal coating sites incorporate PFAS into products such as textiles, leather, carpets, paper, and cardboard. This leads to contamination of air, soil, and sediment through emissions, spills, and improper waste disposal. When polyamide fabrics are exposed to natural elements such as sunlight, precipitation, and wind, distinct patterns of perfluoroalkyl acids (PFAAs) were emitted from each side-chain fluorinated polymer textile used to coat materials to make them water-repellent. PFAS can also migrate from the inner to the outer layers of multilayered fabrics, leading to environmental release through surface contact and washing.27,28
Firefighting foam, particularly aqueous film-forming foams (AFFF), has historically been a significant source of PFAS contamination.29 Consumer products are considered another pervasive source. For example, PFAS have been found in stain-resistant carpeting and nonstick cookware.30 Moreover, several studies have detected significant levels of PFAS in cosmetic products, including cyclic perfluorinated alkanes, perfluorinated ethers, and polyfluorinated silanes.31 In this case, PFAS release occurs during production, handling, and waste management.
PFAS have been widely used in industrial and consumer products since the 1940's. However, they pose significant risks to human health due to their persistence in the environment, potential for bioaccumulation, and diverse toxicological effects.32–34 These “forever chemicals” are linked to a range of adverse health outcomes. Among their most documented effects are disruption to lipid metabolism, thyroid dysfunction, immune suppression, and developmental disruption32–34
PFAS, especially PFOA and PFOS, have been shown to disrupt thyroid homeostasis through multiple mechanisms. These molecules inhibit NIS-mediated iodide uptake into thyroid follicular cells, impairing thyroid function.34 PFOS tends to mimic the effect of the NIS inhibitor perchlorate in its ability to prevent iodide uptake, disrupting hormonal balance.34 Studies found that higher PFOA, PFUnDA, PFOS, ∑4 PFAS (PFOA + PFOS + PFNA + PFHxS), and ∑LC PFAS concentrations were associated with a slight increase in free T4 in teenage boys, suggesting that environmentally relevant concentrations of PFAS may be associated with subtle alterations in the thyroid hormone.35 Nonetheless, other studies suggested that in both female and male adolescents, higher PFOA and PFAS concentrations were associated with lower T4 and lower levels of the Thyroid Stimulating Hormone.36 Though PFAS can induce both hypothyroid and hyperthyroid effects, both outcomes confirm its disruptive impact on the thyroid gland.
PFAS exposure has been consistently associated with impaired immunity and reduced vaccine response in young children.37 Epidemiological research shows that elevated PFAS levels correlate with reduced antibody production following vaccinations, particularly in children.37 In adolescents, while antibody levels naturally decline post-vaccination, PFAS exposure, particularly PFOS, accelerates this decline. However, tetanus antibody levels showed weaker associations, suggesting PFAS may selectively impair responses to certain vaccines. These results reinforce the conclusion that postnatal PFAS exposure drives immune suppression.38
PFAS have been proven to interfere with lipid homeostasis. For instance, a study of 753 middle aged Danes found significant positive correlations between plasma levels of PFOA, PFOS and total cholesterol levels, with a 4.4 mg dL−1 increase in cholesterol per interquartile range rise in PFOA exposure. Similar trends could also be observable with adolescents, as PFOS exposure was linked to 53% higher chances of elevated low-density lipoproteins (LDL).32 These results align with another cohort of the same line in Sweden, where positive correlations were found between PFOA, PFOS, PFDA, and an increase in cholesterol levels.39 A possible mechanism to explain it could be that PFAS alters gene expression in liver cells, as a study found that PFAS-associated DNA methylation in genes like USF2 and CREB5 mediated up to 47% of the observed increase in LDL cholesterol.40
The International Agency for Research on Cancer (IARC) classifies PFAS as a carcinogen, with PFOA classified as a human carcinogen (Group 1) and PFOS classified as a potential carcinogen (Group 2B).41 Additionally, studies conducted in the United States associated PFOA exposure with renal cell carcinoma formation, exclusively among women. Among men, a positive association was observed between PFHxS concentration and chronic lymphatic leukaemia.42 Moreover, epidemiological research has identified an association between PFAS exposure and an increased risk of cancer, particularly kidney and testicular cancer.43 Nonetheless, these associations remain limited to certain types of cancer. It is essential to understand the mechanistic pathways through which PFAS can impact cancer risks in individuals. One proposed mechanism is the induction of oxidative stress, in which PFAS exposure has been shown to increase the cell's production of reactive oxygen species (ROS), which can lead to damage to cellular components, including DNA.44 This damage can result in several mutations, which promote carcinogenesis. In a study conducted by Obiako et al. (2024), cells exposed to PFOA and PFBA produced significantly more ROS compared to untreated cells.44 Another mechanism involves epigenetic effects of PFAS on the cell; in several studies, positive correlations were made between epigenetic age, DNA methylation, and PFAS exposure.45 Data indicate that firefighters, a population that is the most exposed to PFAS, showed DNA methylation at a specific DNA sequence and accelerated aging patterns.45
Overall, although the toxicological literature clearly demonstrates risks, a complete understanding of population exposure requires tracing PFAS emissions through the atmosphere, where their persistence and mobility link industrial sources to remote receptors, including humans. Although PFAS toxicology and sources are increasingly well characterized, their atmospheric behavior remains less well understood. Bridging this knowledge gap is critical, as atmospheric transport and deposition are the primary routes by which PFAS reach remote ecosystems and contribute to long-term exposure risks. Therefore, this review synthesizes current research on atmospheric PFAS by focusing on three key areas: (1) their levels and distribution across polar, midlatitude, and tropical regions; (2) the role and mechanisms of wet deposition, via snowfall, rainfall, ice, and surface water, in determining their atmospheric fate; and (3) their chemical transformations and phase partitioning behavior in the atmosphere.
:
2 FTOH (11.4 pg m−3) > 10
:
2 FTOH (6.27 pg m−3) > 6
:
2 FTOH (2.65 pg m−3).46 The methodology of air sampling appears to be consistent among various studies. Glass fiber filters (GFFs) are used for particle-phase sampling, while polyurethane foam/XAD-2 cartridges are used for gas-phase PFAS collection.48–50 The analytical tool used in studying volatile PFAS is gas chromatography mass spectrometry with positive chemical ionization in selective ion monitoring mode. The standardization of techniques among various studies allows direct comparison of PFAS levels across polar and subpolar regions.
Across latitudes approximately between 55.7°S and 70.4°S, and longitudes from just east of the Prime Meridian (0.001°E) to 73.2°W (blue box shown in Fig. 2), the average concentration of 8
:
2 FTOH (22.04 pg m−3) was significantly higher than that of 10
:
2 FTOH (3.67 pg m−3), which in turn exceeded the level of 6
:
2 FTOH (0.65 pg m−3).48 However, in the western Antarctic Peninsula, approximately 54–69°S and 60–75°W (green box shown in Fig. 2), lower levels of FTOHs were detected, but with a similar trend: 8
:
2 FTOH (6 pg m−3) > 10
:
2 FTOH (2.7 pg m−3) > 6
:
2 FTOH (1.2 pg m−3).50 On one hand, the former includes regions that could be closer to industrial areas, major shipping routes, and continental outflow from South America and Africa.48 On the other hand, the Western Antarctic Peninsula is a more localized and limited zone, with a strong indication of atmospheric transport and degradation processes.50 In regard to the levels of FOSEs and PFOSA derivatives, they appear to be comparable in the two zones and low with the following trend: MeFOSE > MeFOSA > EtFOSE ∼ EtFOSA. It is important to indicate that data on PFAS concentrations in the Antarctic Peninsula remains scarce, and further work is necessary to understand the long-term distribution of forever chemicals and assess ecological risk.
![]() | ||
| Fig. 2 Atmospheric concentrations of FTOHs in Antarctica, as reported in prior studies.48,50 The diameters of the circles are proportional to the detected concentrations. | ||
The Canadian Arctic is a critical region for studying the levels of neutral PFAS in the atmosphere as it reflects LRAT patterns and PFAS distribution globally. The Canadian Arctic also plays a major role in underscoring early indicators for global contamination trends and the effectiveness of international environmental regulations. The occurrence of PFAS in such pristine environments is mainly driven by transport processes due to their chemical persistence.51 Comparing the levels of FTOHs among Hudson Bay (Fig. 3A), Beaufort Sea (Fig. 3B), and Labrador Sea (Fig. 3C), the levels of 8
:
2 FTOH are higher than those of 10
:
2 FTOH and 6
:
2 FTOH. As depicted in Fig. 3, the level of 8
:
2 FTOH is slightly higher in Hudson Bay (49 pg m−3) than Beaufort Sea (44 pg m−3) and Labrador Sea (40 pg m−3).20 For 10
:
2 FTOH, the levels are similar among the three locations, with concentrations of 17 pg m−3 in the Labrador Sea, 14 pg m−3 in Hudson Bay, and 16 pg m−3 in the Beaufort Sea.20 The level of 6
:
2 FTOH is the highest in Hudson Bay (12 pg m−3) and lowest in Labrador Sea (3.7 pg m−3), while the level in Beaufort Bay was intermediate at 9.3 pg m−3.20 In another study conducted by Cai et al.,52 the level of 8
:
2 FTOH in Beaufort Sea (Fig. 3D) (72.27°N, −153.28°E) was found to be higher than the former study20 at 82 pg m−3, but that of 6
:
2 FTOH and 10
:
2 FTOH were lower at 1.7 pg m−3 and 13 pg m−3, respectively. However, the concentrations followed the same trend in both studies: 8
:
2 FTOH > 10
:
2 FTOH > 6
:
2 FTOH.20,52 The differences observed could be attributed to the extraction protocol employed, sampling altitude, spatial coverage, and temporal variability. For instance, the two studies were conducted two years apart in terms of sampling dates. This time difference could have led to variations in environmental conditions such as temperature and atmospheric transport.
![]() | ||
Fig. 3 Atmospheric concentrations of 8 : 2 FTOH (pg m−3) in the Arctic, as reported in prior studies.20,26,49,52–54 Measurements in the following locations are reported: (A) Hudson Bay, (B and D) Beaufort Sea, (C) Labrador Sea, (E) Cornwallis Island, (F) Canadian Arctic Alert, (G) Little Fox Lake, (H) High Arctic Ocean, (I) Chukchi Sea, (J) Bering Sea, (K) Ny-Ålesund, (L) Villum Research Station. | ||
Moreover, Stock et al. revealed that the mean levels of FTOH in Cornwallis Island, approximately at 74°49′N, 94°32′W, in the summer of 2004 were 14 pg m−3 (Fig. 3E), 8.16 pg m−3, and 2.8 pg m−3 for 8
:
2 FTOH, 6
:
2 FTOH, 10
:
2 FTOH, respectively.26 Interestingly, the levels of MeFOSE and EtFOSE appeared to be significantly higher than those of FTOHs at 29 pg m−3 and 23 pg m−3, respectively.26 This finding could be explained by referring to the increased usage of FOSEs in the early 2000s in various consumer products, including surface treatments and firefighting foams.55 Genualdi et al. utilized passive air sampling to study the occurrence of PFAS at various locations, including two major sites in the Canadian Arctic: Alert (82.45°N, 63.50°W) and Little Fox Lake (61.35°N, 135.60°W).54 The levels of 10
:
2 FTOH and 6
:
2 FTOH were below the limit of quantification (LOQ).54 For 8
:
2 FTOH, concentrations were 6.41 pg m−3 in Alert and 16.1 pg m−3 in Little Fox Lake, identified in Fig. 3 as points F and G, respectively.54 The levels of FOSEs and PFOSA derivatives were below the LOQ in both locations. Such low levels of 10
:
2 FTOH, 6
:
2 FTOH, FOSEs and PFOSA derivatives might reflect lower atmospheric prevalence in the studied region, whereas the elevated levels of 8
:
2 FTOH could reveal its common use and greater environmental persistence. Further research is critical to study and analyze PFAS contamination in the Canadian Arctic, with emphasis on identifying emission sources and transport pathways. Expanding analytical datasets in this region would be significant to understand the LRAT of neutral PFAS and their presence in polar ecosystems.
Furthermore, elevated levels of neutral PFAS were revealed along the northward trajectory through the Arctic.52 Referring to Fig. 3 points H, I, and J, the levels of 8
:
2 FTOH were the highest in the high Arctic Ocean (81.5°N, −167.14°E), followed by Chukchi Sea (66.43°N, −168.81°E), and Bering Sea (62.64°N, −175.12°E) at 160 pg m−3, 124 pg m−3, and 103 pg m−3, respectively.52 The concentrations of 10
:
2 FTOH followed the same trend as that of 8
:
2 FTOH at 31 pg m−3, 18 pg m−3, and 11 pg m−3, respectively.52 Those levels could be explained by the global distillation phenomenon, where PFAS migrate from warmer regions poleward to colder ones.56 FTOHs are volatile compounds that could be transported over long distances prior to their condensation or deposition. As for the levels of FOSEs, the levels of MeFOSE and EtFOSE in the high Arctic Ocean were 0.4 pg m−3 and 0.7 pg m−3, respectively.52 However, those levels were the same in both the Chukchi Sea and the Bering Sea at 0.1 pg m−3.52 Generally, the levels of FOSEs are lower than those of FTOHs due to shorter atmospheric lifetimes and degradation en route, limiting their prevalence in the Arctic atmosphere.
It appears that the levels of PFAS between the Eastern Arctic and Western Arctic differ. The classification for the Eastern Arctic and Western Arctic is based on the Primephase Meridian (0°), where the regions to the east of the Prime Meridian are considered the former and those to the west are referred to as the latter. In one of the research stations in the Eastern Arctic, in Ny-Ålesund (78°55′N, 11°56′E), the concentration of 8
:
2 FTOH (10 pg m3; Fig. 3K) is roughly five times that of 10
:
2 FTOH and 6
:
2 FTOH.49 However, the levels of MeFOSE, MeFOSA, EtFOSE, and EtFOSA show49 slight variations, with the highest level for MeFOSA at 0.3 pg m−3 and the lowest for EtFOSE at 0.1 pg m−3. In the Western Arctic, at Villum Research Station, Station Nord (81°36′N, 16°40′W), the concentration of 8
:
2 FTOH (4.9 pg m3; Fig. 3L) is roughly half of that in Ny-Ålesund, while that of 10
:
2 FTOH and 6
:
2 FTOH are comparable.53 However, the concentrations of FOSEs and PFOSA derivatives in the Villum Research station53 are slightly higher than those of Ny-Ålesund.49 The results of comparisons could be attributed to the greater proximity of Ny-Ålesund to European industrial regions and seasonal melt, which is less prevalent at Villum Research Station, Station Nord, where direct input is minimal and ice is more locked.
Neutral PFAS are prevalent in the Arctic, Antarctic and subpolar regions, primarily in the gas phase, with varying levels across multiple regions. The concentration trend of FTOH seems to be consistent with 8
:
2 FTOH > 10
:
2 FTOH > 6
:
2 FTOH. It holds true across various locations, such as the Arctic route, the Western Antarctic Peninsula, the Canadian Arctic, and the High Arctic Ocean. Elevated levels of FTOH are generally observed in zones close to industrialized regions and transportation routes. The concentrations of MeFOSE and MeFOSA are generally low, likely due to their shorter atmospheric lifetimes and degradation patterns; however, some studies report higher levels, reflecting their past widespread use. The literature covering the distribution of PFAS in the polar regions remains limited and underdeveloped, particularly in the Antarctic Peninsula. Further studies should be conducted to enhance the regional understanding of PFAS in such pristine environments to better assess their sources, transport pathways, and environmental fate.
:
2 FTOH levels reaching 30 pg m−3 in Muztagata in the Tibetan Plateau (38.27°N, 74.85°E)60 and 11.3 pg m−3 in Mace Head (53.17°N, 9.50°W; Fig. 6 point J).61
The Northwest Pacific and Japanese Marginal Seas are considered coastal and marginal seas of East Asia, including areas off China, Japan and Korea. The area is heavily influenced by the Kuroshio Current, a warm western boundary ocean current that affects the distribution of pollutants, atmospheric deposition, and the composition of air masses.62 This zone also exhibits a combination of clean marine air and transboundary pollution outflow events from industrialized regions.63 The area represents a wide spatial range from background environments to more impacted ones. In the Sea of Japan, near East China Sea and Korea Strait, roughly placed at coordinates of 36.55°N and 131.97°E, the levels of FTOHs, prevalent in the gas phase, are significant with 250 pg m−3 for 8
:
2 FTOH (Fig. 4A) and a total concentration of 13 PFAS at 346 pg m−3. The levels of MeFOSE, MeFOSA, EtFOSE, and EtFOSA are low at 0.2 pg m−3, with the exception of EtFOSA at 0.5 pg m−3.52 At coordinates of roughly 45.09°N, 140.30°E, off coast of Hokkaido, Japan's northernmost main island, the levels of FTOHs are slightly higher with 8
:
2 FTOH at 289 pg m−3 (Fig. 4B), whereas the levels of FOSEs and PFOSA derivatives are roughly the same. The total concentration of PFAS is 416 pg m−3.52 A possible oceanographic explanation for the observed gas-phase FTOH concentrations is the influence of ocean currents on air-sea exchange and atmospheric chemistry. The Sea of Japan near Korea Strait is greatly influenced by ocean currents and exchange with East China Sea and Pacific Ocean,64 which could possibly dilute or rapidly disperse FTOHs. However, off the coast of Hokkaido, the region is affected by the colder Oyashio Current,65 enhancing accumulation and reducing the rate of oxidation into other forms.
![]() | ||
Fig. 4 Atmospheric concentrations of 8 : 2 FTOH (pg m−3) in selected regions in Asia, as reported in prior studies.25,52,66 Measurements in the following locations are reported: (A) Sea of Japan, (B) off coast of Hokkaido, (C) Tianjin, (D) Beijing. | ||
Furthermore, the levels of PFAS tend to vary notably across different marine regions in East Asia, with samples collected near eastern Taiwan, southern Japan's Ryukyu Islands, northern Japan's Tohoku region, and northern Honshu close to the Sea of Japan.67 Specifically, the highest level of 8
:
2 FTOH is 170 pg m−3 in southern Japan's Ryukyu Island, while the lowest is 12 pg m−3 in northern Japan's Tohoku region.67 This could be attributed to the influence of the Ryukyu Islands to subtropical westerlies and monsoonal flows,68 facilitating the transport of FTOHs from point sources, as well as its proximity to industrialized zones in southern China, Taiwan, and southern Japan.69 According to Fig. 5, in regard to the levels of ionic PFAS, predominantly in the particulate phase, the levels of PFOA and PFOS are the greatest in northern Honshu close to the Sea of Japan, 43 pg m−3 and 5.2 pg m−3, respectively, and lowest near eastern Taiwan, 3.5 pg m−3 and 1.1 pg m−3, respectively.67 Those findings are particularly attributed to the former region receiving continental air masses with higher ambient particulate matter levels, promoting PFAS adsorption onto the particles. The levels of shorter chain PFAS, such as PFHxS and PFHxA, are lower and show less variability than their longer counterparts.67 For instance, the levels of PFHxS are similar at 1.5 pg m−3 near eastern Taiwan, southern Japan's Ryukyu Islands, and northern Japan's Tohoku region, but slightly higher in northern Honshu close to the Sea of Japan at 2.5 pg m−3.
![]() | ||
| Fig. 5 Concentrations of ionic PFAS (PFOA & PFOS) in the particulate phase sampled from both Northern Honshu, Sea of Japan and Near Eastern Taiwan, as reported in prior work.67 | ||
Moreover, the East Asian continental belt is a zone characterized by high population density and heavy industrialization stretching across eastern China, the Korean Peninsula and regions in Japan.70 Remarkably, this zone encompasses the world's largest megacities, such as Seoul and Tokyo, making it a major hub for extensive industrial and manufacturing activities.70 It is also characterized by rapid economic development and urbanization,70 increasing the levels of atmospheric pollutants.71 The region has been affected by the global shift in fluorochemical production, where it has increasingly moved from Western countries to East Asia,72 mainly due to lower labor costs, fewer regulatory restrictions, and increased local demand. A study assessed the levels of PFAS across urban locations in Korea using a passive air sampler (PAS) with polyurethane foam (PUF) and sorbent-impregnated polyurethane foam (SIP), commonly used to collect airborne PFAS for environmental monitoring with a sorbent to enhance the capture of such compounds and without active pumping.73 The average concentrations from 6 urban samples of 10
:
2 FTOH, 8
:
2 FTOH, MeFOSE, and MeFOSA were 10125 pg m−3, 9346 pg m−3, 113 pg m−3, 121 pg m−3, respectively, reflecting the prevalence of emissions from point sources.73 Using XAD-PAS, which is not capable of distinguishing between gas-phase and particulate-phase PFAS, the levels of PFAAs and PFSAs were analyzed across urban and rural locations, mostly covering the Eastern China region.74 The mean levels showed the following trend: PFOA > PFHxA > PFOS > PFNA > PFUnDA > PFHxS.74 This trend could be attributed to the historical use of PFOA and PFHxA in China for manufacturing textiles, coatings, and firefighter foams, whereas longer-chain PFAA, such as PFNA and PFUnDA, are less extensively produced.75 The lower levels of PFOS reflect its legacy contamination and restricted use in industrial applications,75 as it was one of the first PFAS to be regulated under the Stockholm Convention.76
Tianjin is a major industrial and coastal city in northeastern China, known for petrochemical and fluorochemical industries.77 Yao et al. examined the levels of PFAS in Tianjin during both Summers of 2013 (ref. 25) and 2014 (ref. 78) using passive air sampling with PUF-SIP25 and active air sampling with PUF/XAD and GFFs,78 respectively. In regard to the levels of FTOHs, they followed the same trend in both studies: 8
:
2 FTOH> 10
:
2 FTOH> 6
:
2 FTOH,25,78 but such concentrations were higher in the 2014 (ref. 78) than 2013.25 For instance, the concentrations of 8
:
2 FTOH in 2014 (225 pg m−3)78 were roughly 2.8 times higher than those in 2013 (81.7 pg m3; Fig. 4C).25 This could possibly be attributed to increased fluoropolymer production and short-term spikes that are smoothed out in PAS. Regarding the levels of PFOS, they were significantly higher in sampling campaign of Summer 2014 (470 pg m−3)78 as compared to that of Summer 2013 (3.4 pg m−3),25 possibly due to the unauthorized use of PFOS in fluoropolymer production or underrepresentation by PAS. However, the concentrations of PFOA didn't exhibit a significant difference across the two studies.25,78
In Fuxin, China, near a fluorochemicals point source, the level of PFBA was significantly high reaching 1100 pg m−3, followed by PFOA at 600 pg m−3.79 In Beijing, the capital city of China, the concentrations of various PFAS were reported, where the concentrations of 8
:
2 FTOH, 6
:
2 FTOH, 10
:
2 FTOH, and PFBA were significant at 177.2 pg m−3 (Fig. 4D), 26.6 pg m−3, 43.2 pg m−3, and 44.7 pg m−3, respectively.66 Other PFASs were detected at low concentrations such as PFHxA and PFNA at 1.3 pg m−3 and 1.1 pg m−3, respectively.66 Those two studies exhibit a distinction between point-source emissions79 and regional or cumulative pollution.66 The contrast highlights the spatial heterogeneity of PFAS emissions, where proximity to a dominant point source could lead to locally elevated levels. The wide distribution of neutral and ionic PFAS across the East Asian continental belt underscores the need to expand regional atmospheric analysis of these compounds. Such regions could act as hotspots for PFAS accumulation and drivers of their atmospheric transport to more remote atmospheres, affecting global PFAS dispersion.
The North Sea, including its southeastern extension known as the German Bight, is a heavily industrialized and anthropogenically influenced region in northwestern Europe.80 The region also experiences dynamic air-sea interactions due to the occurrence of high winds, cyclonic activity and efficient land-mass sea exchanges.81 The North Sea and its coastal zones have been historically renowned for their petrochemical industries, offshore gas extractions, and shipping activities. Through a cruise sampling campaign from Bremerhaven, a port city on the coast of the North Sea, to the Bay of Biscay, elevated levels of FTOHs were detected, reflecting regional contamination.82 Notably, coastal zones exhibit higher levels of FTOHs via input from nearby sources.83 For instance, as shown in Fig. 6 points A, B, and C respectively, the concentrations of 8
:
2 FTOH in the German Bight, near Heligoland (56 pg m−3), and the West Frisian coast (28 pg m−3) are higher than that in the Dutch Exclusive Economic Zone, an offshore marine environment (16 pg m−3).83 However, the concentrations of N-MeFOSE in the two aforementioned coastal locations at 0.9 pg m−3 and 1.2 pg m−3, respectively, are lower than that of the offshore location at 2.5 pg m−3.83
![]() | ||
Fig. 6 Atmospheric concentrations of 8 : 2 FTOH (pg m−3) in selected regions in Europe, as reported in prior studies.61,83–87 Measurements in the following locations are reported: (A) German Bight, (B) Heligoland, (C) West Frisian coast, (D) Cuxhaven, (E) Schleswig-Holstein, (F) Büsum, (G) Zurich, (H) Manchester, (I) Paris, (J) Mace Head. | ||
Furthermore, the German coastline features multiple industrial and port facilities, including those in Hamburg, Bremen, and Wilhelmshaven. Jahnke et al. studied the atmospheric levels of fluorotelomer alcohols in Germany, revealing elevated levels of FTOH, FOSE, and FOSA in Hamburg with the maximum total concentration of FTOH reaching 546 pg m−3 and that of FOSE and FOSA at 151 pg m−3.88 Similarly, Dreyer and Ebinghaus demonstrated83 high concentrations of FTOH in Hamburg, with a total concentration reaching 180 pg m−3. The total concentration of all neutral PFAS studied was 224 pg m−3.83 Close to the German coast, near Cuxhaven, characterized by high population density and heavy industrialization, the total concentration of neutral PFAS reached 177 pg m−3.84 Among all the neutral PFAS compounds analyzed, 8
:
2 FTOH exhibited the highest atmospheric concentration, measured at 75 pg m−3 (Fig. 6 point D).84 However, lower concentrations of PFAS were detected in more rural regions in Germany, such as Elbe Estuary Margin in Schleswig-Holstein (54.226°N, 8.226°E)84 and Büsum (54.13°N, 8.86°E),87 with the total concentration of neutral PFAS measured 61 pg m−3 and 41 pg m−3, respectively. As depicted in Fig. 6, the concentrations of 8
:
2 FTOH in the two regions were 29 pg m−3 (E) and 25 pg m−3 (F), respectively. Those measurements show that the rural atmosphere is influenced by transported pollution from urban and industrialized regions, reflecting background contamination. Studying this type of transported pollution further is essential to understand baseline exposure and guide control strategies.
European and North American cities are characterized by diverse industrial and consumer activities, along with growing populations.89 Although several regulatory reforms have been implemented to reduce environmental PFAS levels, residual contamination and PFAS variants remain concerning.90 In Zurich, Switzerland, referring to Fig. 6, significant levels of 8
:
2 FTOH were recorded at 700 pg m−3 (G), reflecting strong ongoing emissions.85 The particle-bound concentration of PFOA (7.7 pg m−3) was higher than that of PFOS (2.3 pg m−3).85 However, in Birmingham, United Kingdom (UK), using PAS, the level of PFOS was roughly two times greater than PFOA.91 The levels could be reflective of local emission profiles and historical differences in PFAS use. In Manchester, UK, significant concentrations of particle-bound PFOA and gas-phase 8
:
2 FTOH were detected at 341 pg m−3 and 237 pg m−3 (Fig. 6 point H), respectively.61 Those levels might indicate emissions from industrial activities and consumer product degradation, as well as higher exposure risk as compared to other European cities. The coexistence of elevated PFOA and 8
:
2 FTOH suggests that atmospheric degradation of volatile precursors such as 8
:
2 FTOH may contribute to PFOA formation.92 In Paris, France, Rauert et al.86 revealed high levels of FTOH in 2015, with the following trend: 8
:
2 FTOH (121 pg m3; Fig. 6 point I) > 6
:
2 FTOH (78 pg m−3) > 10
:
2 FTOH (37 pg m−3). The spatial variability observed between Zurich, Birmingham, Manchester, and Paris shows that different factors, such as local emission sources, historical usage profiles, and variations in consumer patterns, shape PFAS distribution across urban environments in Europe.
As compared to Toronto, Canada, the levels of FTOHs were lower than those of Zurich, Manchester, and Paris, and followed a slightly different trend than the one revealed in Paris: 8
:
2 FTOH (40.2 pg m−3) > 10
:
2 FTOH (21.1 pg m−3) > 6
:
2 FTOH (17.7 pg m−3),46 possibly attributed to differences in urban density and industrial activities. Interestingly, the particle-bound concentrations of some ionic PFAS in Albany, New York, United States of America (USA), are low with the following trend: PFOA (2.03 pg m−3) > PFOS (0.64 pg m−3) > PFNA (0.64 pg m−3).93 Elevated PFAS levels were detected in Cleveland, Ohio, USA, with the total concentration of 41 PFAS measured94 at 410 pg m−3, likely reflecting proximity to manufacturing facilities and dense traffic. While detectable PFAS levels confirm their presence in the atmosphere, these compounds remain significantly understudied in the midlatitude North American atmosphere compared to water and soil matrices. Most studies that aimed at determining the levels of PFAS in such regions tackled their detection in forms of wet deposition, rather than the gas and particulate forms, which establishes a major knowledge gap.
As for subtropical regions, they are localized between approximately 23.5° and 35° latitude in both hemispheres, bordering the tropics57 (Fig. 1). Those zones are typically less humid than the tropical ones and experience warm to hot summers, along with cooler winters.57 Precipitation is less consistent than the tropics, where some areas experience dryer summers than others. Some areas within this zone include the Mediterranean Basin, Northern India, parts of South America, and Southern China. Noteworthy, the subtropical latitudinal band houses many of the world's developing industrial facilities, acting as major contributors to PFAS contamination.96
However, literature on atmospheric PFAS in tropical and subtropical regions remains limited and underdeveloped, particularly in areas like Africa and the Middle East. Field measurements for atmospheric PFAS in such regions are important to better understand how desert dust influences the accumulation of these compounds. Additionally, political instability, uncontrolled industrialization, and poor environmental regulations are major drivers for the presence of atmospheric pollutants in the Middle East.97 Such reasons indicate that PFAS concentrations could be significant in the regional atmosphere and quantifying the levels would serve to close some knowledge gaps.
Across Atlantic Ocean transects, extending from the equatorial, near the Gulf of Guinea, to tropical and subtropical zones in the North and South Atlantic, the changes in PFAS concentrations reflect geographic distribution and emission patterns.82 Near the equatorial and south tropical Atlantic, the concentrations of 10
:
2 FTOH and 8
:
2 FTOH are relatively low, whereas that of 6
:
2 FTOH is below the detection limit.82 For instance, near the Gulf of Guinea across the equatorial Atlantic, the concentrations of 10
:
2 FTOH and 8
:
2 FTOH are 2.9 pg m−3 and 13 pg m−3, respectively.82 As for the levels of FOSEs and PFOSA derivatives, they were either very low or below the detection limit.82 In the Northern Atlantic, the levels of FTOHs are significantly higher, particularly 8
:
2 FTOH and 6
:
2 FTOH.82
The South China Sea industrialized coast hosts major manufacturing and production hubs in Asia.98 Shenzhen, China, has experienced rapid growth in recent years, with multiple potential PFAS sources, such as textile, petrochemical, and electronic industries.99 Using PAS, Liu et al. assessed99 the levels of 11 perfluorinated compounds (PFCs) in Shenzhen's atmosphere in the fall of 2011. Their total concentrations were averaged at 15 pg m−3, with the presence of all 11 PFCs at all 13 sampling sites, demonstrating pervasive PFAS pollution.99 The levels of PFOA and PFOS predominated, averaging at 5.4 pg m−3 and 3.1 pg m−3, respectively.99 In the northern South China Sea, the Dongshan Marine Station is located within an atmospheric pathway influenced by northeasterly winds during winter,100 facilitating the transport of PFAS from nearby industrial and urban emission sources toward the open sea. In October and from December 2019 to January 2020, Yamazaki et al. revealed that the sum of 12 ionic PFAS averaged at 24 pg m−3, with the maximum value reaching 33 pg m−3.101 Both recorded in October, the greatest detected atmospheric concentration was that of PFOA (9.08 pg m−3), followed by that of PFOS (8.64 pg m−3).101 The levels of PFOA and PFOS appear to be higher in the Dongshan Marine Station than those in Schenzen by a factor of roughly 2–3. Although Schenzen's atmosphere is known to be heavily influenced by the semiconductor industry and consumer activities, the levels could be lower than the Dongshan Marine Station as the studies were conducted 10 years apart. It is encouraged that future work tackles data collection from various regions in China to inform policy about long-term changes in legacy PFAS concentrations. Shanghai, another major industrial and commercial zone in China, was found to suffer from high levels of atmospheric PFAS contamination.96 Referring to Fig. 7, the concentrations of FTOHs were found to be significant, with 8
:
2 FTOH measured at 923 pg m−3.96 Referring to Fig. 7, the concentration of 8
:
2 FTOH in the Taiwan Western Strait was reported101 as 146 pg m−3. Near Guangdong, China, the concentrations of PFAS vary across different locations, nearshore urban-industrial, transitional offshore, and remote offshore sites.102 The concentrations of 8
:
2 FTOH dominate at all three sites (Fig. 7), particularly at the two offshore sites, measured at 40.1 pg m−3 and 36.2 pg m−3, respectively.102 The levels of 6
:
2 FTOH were the lowest across all sites, but such levels are higher in the offshore locations.102 The levels of 8
:
2 FTOH were high in Shanghai, likely due to measurements being collected inland near emission point sources. In contrast, concentrations in the Taiwan Strait were also elevated but lower than those in Shanghai, as the sampling sites were located near the coast. Offshore levels were lower, though not negligible, reflecting the influence of LRAT from nearby regions and emissions from shipping activities.
![]() | ||
Fig. 7 Atmospheric concentrations of 8 : 2 FTOH (pg m−3) at selected coastal East Asian locations, compiled from previous studies.96,101,102 Shanghai showed the highest reported concentration among the displayed sites (923 pg m−3). | ||
In Brazil, the levels of atmospheric PFAS are distributed through a tropical and subtropical gradient, extending from urban and industrialized to remote and pristine environments. São Luís do Maranhão is a major component of Brazil's Carajás mining,103 petroleum refinery104 and transportation105 activities. As depicted in Fig. 8, Saini et al. revealed106 that the level of atmospheric concentration of PFOA (24 pg m−3) in the region appears to be higher than that of PFOS (13.2 pg m−3), suggesting potential point source emissions. In Curitiba, South of Brazil, an urban environment, the concentrations of PFOS and PFOA in PM2.5 sampled in December 2021, ranged between 0.013–0.29 pg m−3 and 0.016–0.28 pg m−3, respectively.107 It was suggested that a possible source of PFOS could be the use of pesticide sulfluramid in the north direction to Curitiba and its transportation by wind.107 Another suggested source of both PFOS and PFOA was the wastewater treatment plant affecting the atmosphere of the sampling site.107 Reflecting the influence of LRAT on the accumulation of atmospheric PFAS in the Amazon Basin, the mean PFOA levels in total suspended particles throughout 24-hour sampling ranged from 0.01 to 2.0 pg m−3.108 Literature on the dispersion of atmospheric PFAS in Latin America remains underdeveloped and limited. A region of specific interest is the Amazon Basin that houses the largest rainforest in the world. Such environments are important as they reflect the global atmospheric circulation and cycling patterns of PFAS in tropical atmospheric systems. However, there are significant gaps in the current body of literature pertaining to the study of PFAS levels and distributions in the Amazon Basin. Future studies are encouraged to focus on expanding atmospheric PFAS data for this underrepresented region, which would fill a significant geographic and mechanistic gap in the understanding of global contamination.
![]() | ||
| Fig. 8 Atmospheric concentrations (pg m−3) of PFOA and PFOS in São Luís do Maranhão, as reported in prior work.106 The map shows that the concentration of PFOA (24 pg m−3) is higher than that of PFOS (13.2 pg m−3). | ||
This removal process includes in-cloud scavenging during which PFAS or aerosols are incorporated into cloud droplets through a process called nucleation. In this process, they can act as cloud condensation nuclei (CCN) or ice nuclei (IN). Another pathway is called in-cloud impaction scavenging, which involves aerosols particles being collected with existing cloud droplets or ice crystals. These aerosols will eventually be eliminated from the atmosphere when the cloud droplet or ice particle becomes heavy enough to fall as precipitation, rain or ice.112–114 Another mechanism, known as below-cloud scavenging, involves precipitating raindrops or snow particles capturing PFAS as they descend through the air beneath the cloud via collisional interactions. Studies have shown that this type of scavenging is significantly influenced by the size distribution of falling raindrops.112,114,115 In-cloud scavenging occurs when PFAS are directly incorporated into cloud droplets during condensation. These contaminated droplets eventually fall to the ground as rain or snow.
Snow deposition has been known to play a crucial role in PFAS transfer to the cryosphere and hydrosphere. Snow can effectively scavenge both particle-bound and dissolved PFAS from the atmosphere and temporarily store them until seasonal melt releases them into surface water.116,117 Snow scavenging has been proven to be more efficient for long-chain PFCAs, which are often associated with sea-salt aerosols.116 This phenomenon is attributed to the higher hydrophobicity of PFCAs and their tendency to associate with particulate matter and atmospheric aerosols. Interestingly, snow, due to its larger surface area, can capture both vapor-phase and particle-bound compounds, leading to more effective removal of heavier, less volatile molecules from the atmosphere.118
Wet deposition represents one of the most important processes in atmospheric cycling of PFAS, especially for ionic PFAS such as PFOA, PFNA, PFHxS, and PFOS, which are effectively non-volatile under environmental conditions and therefore rely almost entirely on snow, rain, and cloud water scavenging for atmospheric removal. Numerous studies identified wet deposition as the dominant atmospheric sink for these compounds, as Xia et al. , showed 60% of PFOA and 50% of the PFOA detected in the Great Lakes came from wet deposition.94 Similarly, in a study conducted in South Florida, 21 legacy and emerging PFAS were detected in rainwater with PFCAs, accounting for 74% of the measured PFAS load. The consistent detection across seasons and sampling sites indicates that precipitation acts as a continuous, diffuse source of PFAS to soils, urban surfaces, and aquatic systems. The significance of this process varies to climate: in temperate regions, rainfall contributes most of the yearly downward flux, whereas in Arctic, sub-Arctic and high altitudes environments, snowfall becomes more influential because of its high scavenging efficiency, its ability to accumulate PFAS over time and its eventual release during melt events.93,110 However, once deposited, volatile precursors can undergo re-volatilization, significantly increasing their residence time. On the contrary, ionic PFAS, exhibit extremely low vapor pressures, hindering their re-volatilization from dry surfaces. They typically re-enter the atmosphere indirectly, via sea spray aerosols or wildfire smoke. Re-volatilization is influenced by several factors and environmental conditions such as temperature, humidity and the chemical properties of the compounds themselves. Higher temperatures can increase the volatility of PFAS, especially short-chain compounds, enabling them to easily transition from particulate to gas phase.94 Moreover, relative humidity also plays a pivotal role. Higher relative humidity leads to the adsorption of water molecules, inducing competition for adsorption sites on soil minerals, and weakening PFAS-soil interaction.119 Moreover, PFAS sorption and desorption can vary depending on the surface properties, such as the soil type, organic content, and surface roughness. Surfaces with high organic carbon bind PFAS more strongly, preventing the re-volatilization of precursors, while sandy soil will bind PFAS weakly.120 This re-volatilization process can significantly affect long-term environmental exposure to PFAS. As PFAS re-enter the atmosphere, they can be transported over long distances and deposited again through wet or dry deposition, perpetuating their presence in the environment.121 This cyclical process contributes to the persistence and widespread distribution of PFAS making them challenging to manage and mitigate. Sea Spray Aerosols (SSA) play a crucial role in the atmospheric transport and deposition of long-chain PFCAs. These aerosols are generated from the ocean surface and serve as carriers for PFCAs, especially those with longer chains and surfactant properties. During the formation of sea sprays, long-chain PFCAs tend to partition preferentially into the surface microlayer and are subsequently ejected into the atmosphere through bubble bursting mechanisms.121 Once airborne, these substances become adsorbed onto SSA particles, serving as an efficient condensation nuclei for snowfall. A study conducted by Johansson et al. (2019) demonstrated that enrichment factor (EF), defined as the ratio of the concentration in the surface microlayer (SML) to the concentration in the bulk seawater, was significantly higher for long chain PFCAs in SSA compared to short-chain compounds. The SML EF ranged from 13 to 47 for long chain PFCAs, while short chain PFCAs had much lower values with factors of 1.2–2.9 for C9 compounds and 1.1–1.2 for C6 PFCAs.121 Moreover, a study conducted in Antarctica detected only PFCAs at quantifiable levels, while shorter chain PFAS were below detection limits.122 These results indicate that snowfall selectively scavenges long-chain PFAS because they partition more strongly to SSA. This pattern was also highlighted by Casal et al. (2017), who also reported the highest concentrations for PFCA homologues.116 Collectively, these studies highlight the role of chain length in enrichment mechanisms, where the longer chain compounds efficiently partition into SML and are transferred to SSA. Once transferred, the compounds can travel long distances to remote regions, such as Antarctica.
Furthermore, FTOHs and FTAs are not necessarily permanently removed from the atmosphere. Instead, they can re-volatilize after deposition. For instance, flux measurements of FTOHs and FTAs have shown positive air–snow exchange, especially in warmer conditions, indicating re-emission from snow to air during the summer, reaching 118 pg m−2 d−1.48 A 2023 study on Svalbard's surface suggested that both FTOHs and FTAs can be released from snow after deposition, driven by warming temperatures and melting snow.117 These findings show that snowpacks may act as temporary PFAS reservoirs, particularly during the summer, contributing to secondary PFAS pollution.
In summary, wet depositions play a critical role in the atmospheric removal and redistribution of PFAS, particularly long-chain compounds. Snow has been proven to be highly efficient for PFAS scavenging due to its large surface area and capacity to trap both gas-phase and particle-phase compounds. Sea spray aerosols further contribute to atmospheric loading of PFAS, serving as carriers for surface-enriched long-chain compounds. However, the notion that snow serves as a permanent sink is increasingly challenged by studies revealing re-volatilization of PFAS during warmer periods, highlighting the transient nature of snowpacks as PFAS reservoirs.
Nevertheless, several gaps still remain in PFAS wet deposition literature. For instance, the role of fog as a deposition pathway remains underexplored, especially in urban and coastal areas. Moreover, despite their rising prevalence and distinct mobile behavior, short-chain and emerging PFAS are less studied than legacy long-chain ones.
Table 2 shows the concentration of PFAS in rain, ice and snow as well as deposition flux among various locations of sampling. Precipitation-based sampling shows PFAS are ubiquitous in atmospheric deposition, even in remote regions. For instance, rainwater studies in Japan, show measurable concentrations of PFAS at several intervals during single rainfall events, with the total flux ranging from 40.8 to 186 ng per m2 per day (Table 2). The major PFAS compounds found in rainfall were PFBA, PFNA and PFOA, indicating continuous atmospheric scavenging of PFAS away from sources.123 Moreover, a study conducted in Wilmington,USA detected a total PFAS concentration reaching 110 ng L−1 in rainfall along with a deposition flux of 0.3–29 ng per m2 per day.124 Moreover, another study conducted in Wisconsin as part of the National Atmospheric Deposition Program reported the detection of 1.3 to 47.4 ng per m2 per day PFAS flux.125 Complementary to these findings, Kim and Kannan (2007)93 reported notable PFAS concentrations in rainfall and lakes from various locations across the United States. PFOA concentrations in urban lakes ranged between 4.38 and 15.8 ng L−1, while lower levels were detected in rural areas, ranging between 1.24 and 3.87 ng L−1. European data reveal a similarly wide range of concentrations: in Germany, the major PFAS compounds detected in rain were PFOA and PFBA with a total PFAS concentration of 1.6 to 48.6 ng L−1 and a deposition flux ranging from 2 to 91 ng per m2 per day.126 Similarly, Han et al. (2019) documented substantial variability in PFAS concentrations in precipitation samples from cities across China, linking elevated levels directly to fluorochemical manufacturing activities. Measurable PFAS concentrations were also detected at rural background sites.74 In the study, PFAS variations depended on their local source emissions as well as regional atmospheric transport. Additionally, the total annual wet deposition fluxes reported in Chinese urban areas are significant, with one study reporting a total of 14.3 ng per m2 per day, dominated by PFBA (4.93 ng per m2 per day) and PFOA (3.29 ng per m2 per day), followed by PFOS and other PFCAs127
| Author | Location of sampling | Period of sampling | Types of PFAS compound measured | Type of precipitation studied | Concentration in rain of ΣPFAS/ice/snow (ng L−1) | Deposition flux (ng per m2 per day) |
|---|---|---|---|---|---|---|
| Pfotenhauer et al., 2022 (ref. 125) | Wisconsin, USA (upper Great Lakes Location) | 5 Months | 34 per- and polyfluoroalkyls (PFAS), mainly PFCAs | Rain | 0.7–6.1 (median 1.5) | 1.3–47.4 (median 5.7) |
| Wang et al., 2022 (ref. 128) | Chongqing, China (metropolitan, subtropical) | July 2020–April 2021 (4 seasons) | PFBA, PFPeA, PFHxA, PFHpA, PFOA, PFNA, PFDA, PFUdA, PFDoA, PFTrDA, PFTeDA, PFHxDA, PFODA, PFBS, PFHxS, PFOS, PFDS (17) | Rain | 3.31–196.14 | 13.9 |
| Hartz et al., 2023 (ref. 110) | Lomonosovfonna Ice Cap, Svalbard, Norway (High Arctic) | A decade, 2007–2018 | TFA, PFOS, C2–C11 PFCAs (45 targeted, 26 detected) | Ice core | 9.51–16,500 | 0.0068–22.45 |
| Taniyasu et al., 2013 (ref. 123) | Japan (Tsukuba, Mt. Tateyama, Pacific Ocean) | During seven rainfall events: | PFBS, PFCAs, FTOHs | Rain; surface snow; snow core | Rain: NR, surface snow: 3.04–40.5 | 40.8–186 |
| 1 July 2006 | Snow core: 0.884–4.51 | |||||
| 12 December 2006 | ||||||
| 16 April 2007 | ||||||
| 10 June 2007 | ||||||
| 14 June 2007 | ||||||
| 19 October 2007 | ||||||
| 12 January 2008 | ||||||
| S. Wang et al., 2022 (ref. 127) | Xiamen, China (Subtropical) | 1 Year | PFOS, PFOA, PFBA, 6 : 2 Cl-PFESA (4) |
Rain | 0.20–180.65 (average 10.71) | 14.24 |
| Maclnnis et al., 2017 (ref. 129) | Devon Ice Cap, Canada | 14 Years (1993–2007) | PFBA, PFECHS, PFAAs (PFCAs, PFSAs), FOSA | Snow Pit | NR | <0.003–0.8 |
| Young et al., 2007 (ref. 130) | Arctic Ice Caps (North) | 1996–2005 | PFOA, PFNA, PFDA, PFUnDA, PFOS | Snow core | Low to mid pg L−1 | 0.42 |
| Dreyer et al., 2010 (ref. 126) | Northern Germany | 7 months (2007–2008) | PFOA, PFBA (34) | Rain | 1.6–48.6 | 2.0–91 |
| Shimizu et al., 2021 (ref. 124) | Wilmington, USA | December 2018–December 2019 (1 year) | PFOS, PFOA, PFECAs, HFPO-DA, PFMOBA, PMPA | Rain | LOQ-110 | 0.3–29 |
| Casal et al., 2017 (ref. 116) | Livingston Island, Maritime Antarctica | December 2014–February 2015 | PFCAS (PFOA, PFNA), PFSAs (PFOS) | Snow | 0.76–3.6 | NR |
When compared, these studies illustrate both strong points of agreement and notable contradictions across regions. A consistent trend is the dominance of short-chain PFCAs, especially PFBA, in rainfall, supporting the growing scientific consensus that these more mobile compounds are increasingly present in the atmospheric PFAS pool as industries phase-out long chain PFAS. However, the large variability in reported concentrations and fluxes ranging from a few ng per m2 per day in rural areas to almost 100 ng per m2 per day near urban or industrial centres highlights how wet deposition is strongly shaped by local atmospheric chemistry, precursors, meteorological conditions and proximity to sources such as local industries and urban activities.93 Methodological differences in both sampling and analysis may also contribute to this variability. Sampling approaches vary in whether they are event-based or cumulative, as well as in the type of precipitation collected. Analytical differences include variations in detection limits and the range of analytes targeted in each study.
Snow cores from the Arctic and Antarctic confirm deposition of diverse PFAS, including long- and short-chain PFCAs, PFSAs, and replacements like HFPO-DA (GenX), highlighting LRAT.117 Snow cores are particularly valuable as environmental archives, providing historical records for global PFAS distribution and atmospheric deposition trends over decades. For instance, analysis of ice cores from the Devon Ice Cap in the Canadian Arctic revealed increasing PFAS concentrations starting in the mid-1980s, corresponding closely with the global industrial-scale production and use of PFAS compounds.129 Deposition in the Arctic showed positive correlations with solar flux, which can suggest a strong photochemical formation pathway from volatile precursors like FTOHs and sulphonamide compounds.110,117 Notably, deposition fluxes during 24-hour daylight periods were 7.9 to 71 times higher than those collected during dark periods.117 Collectively, these snow-core-derived data offer unique insights into historical emissions, global dispersion patterns, and the effectiveness of regulatory actions over time. Some of these regulations include usage restrictions such as the Toxic Substance Control Act (TSCA) imposed by the EPA, requiring companies to notify the EPA before manufacturing or importing certain types of PFAS.131 Moreover, the EPA is proposing bans or restrictions on the most hazardous PFAS as a part of the PFAS Strategic Roadmap. The 2023 Proposal includes the ban on most uses of PFOA, PFOS, PFNA, and GenX.132 Additionally, in Europe, several PFAS, including PFOA, PFOS, and PFHxS are restricted or banned under the Stockholm Convention.133 While these measures would contribute to the reduction of PFAS use in developed countries, they reflect a growing global divide. While both the United States and Europe have implemented strict restrictions on PFAS production and use, many developing countries that often lack these regulatory infrastructures or economic leverage remain vulnerable to both unregulated PFAS usage and transboundary atmospheric transport of PFAS emitted elsewhere.
In European alpine regions, snow samples taken from the Ortles glacier revealed PFBA in dominance in surface layers, which is consistent with its widespread current use and high mobility. Deeper layers showed increased concentrations of PFOA and PFNA, reflecting post-depositional migration driven by meltwater percolation.116 This process selectively removes short-chain PFAS, while retaining longer chains, modifying the chemical profile with depth.134 Remote snow records from the Devon Ice Cap in Canada showed that annual PFCA fluxes increased after 1985, peaking in the 2000s, and declined slightly post 2012, which is due to the US EPA's PFOA Stewardship Program and Canadian Environmental Agreements134 (Fig. 9). However, deposition of short-chain PFAS such as PFBA has continued or even increased, highlighting the ongoing global shift toward short-chain replacements.134,135
![]() | ||
| Fig. 9 The annual deposition fluxes of PFOA (a) and PFNA (b) in ng per m2 per year on the Devon Ice Cap. The solid black line represents the 5-year moving average. Reproduced from Pickard et al.,134 sourced from Atmospheric Chemistry and Physics, licensed under CC BY 4.0, available online at DOI: https://doi.org/10.5194/acp-18-5045-2018. | ||
The Tibetan Plateau, often referred to as Earth's “Third Pole”, presents another instructive case. Despite its remoteness, regions like Tianshan and Laohugou have recorded elevated PFAS concentrations in snow of 2.35 ng L−1 and 2.3 ng L−1, respectively, attributed to long-range transport from South and East Asian industrial centres.135 Similarly, a study conducted by Casal et al. (2017) reported concentrations ranging from 0.76 to 3.6 ng L−1 in freshly deposited snow and a concentration of 0.082 to 0.43 ng L−1 in surface snow on Livingston island116 (Table 2). Even near the summit of Mount Everest (∼8850 m), measurable levels of PFAS in snow were detected, with PFOS and PFOA reaching concentrations of 26.4 ng L−1 and 2.14 ng L−1, respectively. These findings highlight the remarkable vertical extent of PFAS atmospheric dispersion.136 Similarly, in the Arctic region, PFOS and PFOA were the most prominent PFAS with a concentration range of 0.003–0.086 ng L−1 and 0.014–0.147 ng L−1, respectively. In European Alps, the major PFAS found were PFOA with a concentration ranging from 0.2 to 0.6 ng L−1 and PFBA with concentrations from 0.3 to 1.8 ng L−1.137 Additionally, Young et al. (2007) quantified PFAS in snowpacks in the Arctic region, finding concentrations ranging from low to mid pg L−1 with a deposition flux of 0.42 ng per m2 per day (ref. 130) (Table 2). PFAS in remote regions highlight their persistence and mobility, driven by atmospheric transport and gas–particle partitioning.
To conclude, the global scale presence of PFAS in atmospheric deposition from urban rainfall in the U.S and Germany to snowpacks in the Arctic, Antarctic, and high-altitude regions like the Himalayas underscores their persistence, mobility, and long-range transport potential. Precipitation acts as both a transport medium and temporary reservoir, with snow preserving long-term deposition trends linked to industrial activity and regulation. Despite regulatory actions in many industrialized nations, the continued detection of PFAS, in remote and high-altitude environments indicates ongoing global emissions and gaps in enforcement or substitution strategies.
While annual cumulative deposition fluxes are often reported, high-resolution, event-based deposition data from diverse regions are scarce, which limits temporal trend analyses and source attribution. Standardization of sampling and analysis techniques is also necessary to provide a more nuanced approach in PFAS regulation. Additionally, no published study has quantified the percentage of total atmospheric PFAS wet deposition to each precipitation type (rain, snow, fog) in a globally representative way. While numerous datasets report concentrations or fluxes in rain versus snow, the absence of systematic, region-wide comparative data means that we cannot yet assign a definitive share to any single precipitation form.
:
2 FTOH and PFOA declined by 98–90% within just 5 km of an industrial source, whereas short-chain PFAS remained detectable even 40 km away.94
One key insight from global deposition studies is that depositions represent a sink for atmospheric PFAS but a source of PFAS for surface systems such as soils or water. While precipitations remove PFAS from the atmosphere, these compounds are then introduced to land, snow, and water where they accumulate.94,138 These dual roles complicate risk management efforts, as removing PFAS from the atmosphere does not prevent accumulation in surface systems.
Once PFAS are deposited from the atmosphere, they often reach aquatic environments via direct precipitation, snowmelt, or runoff. This process is well documented in both urban and remote settings. In the Great Lakes region, atmospheric deposition accounts for over 90% of PFAS input to Lake Superior, despite its size and distance from point sources.94 Another study conducted by Filipovic et al. (2015) in a pristine region in Sweden found a positive mass balance of PFAS in the riverine. Atmospheric deposition contributes to aquatic PFAS directly and indirectly through soil accumulation and subsequent transport to surface waters. Since these compounds do not readily degrade, they tend to accumulate in soil through atmospheric deposition before being transferred to the surface waters, confirming that major pathway of PFAS entry into the Baltic Sea is via deposition.139 These results could also be confirmed by a study in Canada where snowpacks were proven to be a significant temporary PFAS reservoir during the winter. These molecules accumulate in snow layers due to atmospheric deposition, effectively concentrating contaminants until spring melt.140 Other lakes, such as Michigan and Huron, exhibit net accumulation of PFAS, reflecting sustained inputs for atmospheric deposition, surface runoff, and tributary inflows. This net accumulation in large lakes often results from limited outflow, relatively slow flushing rates, and high watershed-to-lake surface area ratios, which collectively enhance retention.94 Codling et al. (2018) further confirm these patterns, reporting that Lake Michigan sediment cores clearly document the persistent PFAS accumulation over recent decades.141 In contrast, Lakes Erie and Ontario exhibit net exporters, effectively removing PFAS through hydrological outflow rather than accumulation in sediments.94
The efficiency of PFAS scavenging by precipitation plays a pivotal role in determining their atmospheric residence time, transport range, and eventual deposition patterns. While long-chain, particle-bound PFAS are effectively removed during rainfall events, short-chain, volatile compounds often escape such removal and remain airborne, facilitating LRAT. Importantly, atmospheric deposition functions as both a removal pathway from the air and a significant source to terrestrial and aquatic ecosystems. Numerous studies from the Great Lakes, Sweden, and Canada have demonstrated that deposited PFAS accumulate in snowpacks, soils, and surface waters often serving as long-term reservoirs. These deposits can be remobilized through snowmelt, runoff, or slow flushing, especially in large water bodies with high retention capacity like Lake Superior and Lake Michigan. In contrast, lakes with higher outflows, such as Erie and Ontario, may exhibit net PFAS export. Ultimately, while atmospheric deposition reduces airborne PFAS burdens, it contributes substantially to their environmental persistence and complexity in downstream ecosystems. This dual role underscores the importance of integrating atmospheric and hydrological models in PFAS risk assessments and environmental management strategies.
:
2 to 10
:
2 to 6
:
2 FTOH near polar regions.48 Xie et al. found an elevated ratio of 8
:
2 to 10
:
2 to 6
:
2 FTOH near the Arctic, demonstrating the significant role of LRAT.49 Over the northeastern Atlantic Ocean, the levels of FTOHs were revealed142 to be inconsistent across measured samples, with strong influence from land-based contributions as the highest recorded level was 156 pg m−3. Such fluctuations indicate that local emission sources, such as industrialization, highly contribute to the levels of FTOHs in the studied marine environment and hinder uniform distribution. In the Tibetan Plateau, a remote region, the concentration of neutral PFAS tends to be high, particularly 8
:
2 FTOH, due to LRAT from industrial regions.60 In fact, the relative ratios of 8
:
2, 10
:
2, and 6
:
2 FTOHs further demonstrate the aging of air masses in remote regions, in contrast to fresher emissions near cities.60
Although the main source of PFAS in Arctic regions is LRAT, marine aerosols are considered to be another source that could be dependent on several external factors. Sha et al. revealed seasonal variations to the contribution of sea spray to PFAS as it appears to be higher than that of precursor degradation in the winter.138 In winter, wind-driven transfers from the ocean to the atmosphere are more consistent and the concentrations of OH radicals seem to be limited, inhibiting atmospheric oxidation of volatile PFAS.138 However, in summer, photochemical transformations become more important contributors due to the increase in the activity of atmospheric oxidation pathways.138 This is consistent with the finding presented by a study that sampled ice cores from the Devon Ice Cap, Devon Island, Nunavut, where there seems to be minimal contribution from marine aerosols in the sampling month of May.134
Moreover, a study was conducted to examine the historical trends of atmospheric oxidation of polyfluorinated amides (PFAMs) and their potential as contributors to PFCAs and PFOA.143 It was revealed that N-ethylperfluorobutyramide (EtFBA) could be oxidized rapidly by both chlorine and hydroxyl radicals, with a lifetime of roughly 4.4 days with the latter.143 The degradation products included perfluorobutyramide (C3F7C(O)NH2), TFA, PFPrA, and PFBA.143 Remarkably, PFCA formation was also revealed from the oxidation of intermediate fluorinated radicals, which leads to the release of COF2 through sequential transformations and the eventual production of stable PFCA end-products.143 It was suggested that Arctic branched PFOAs are the result of PFAM oxidation, instead of environmental transport.143
Although methyl perfluorobutane sulfonamidoethanol (MeFBSE) is highly reactive and degrades quickly in the atmosphere, elevated concentrations were identified in Antarctica.50 This unexpected finding could suggest the presence of distant point sources, LRAT, or degradation of certain precursor compounds.50 Interestingly, MeFBSE and methyl perfluorobutane sulfonamide (MeFBSA) are precursors for the formation of short-chain perfluoroalkyl acids, which are resistant to further transformations.50 Their highly persistent properties and their water solubility result in their detection in Antarctic surface waters.50 The pathways leading to the formation of short chain in the atmosphere remain underdeveloped in the literature. Future research tackling this knowledge gap is important to understand the persistence of short chain PFAS, considering the increase in usage and production in industries due to shifts in policy regulations worldwide.
The transformations and atmospheric behavior of PFAS could be understood through their occurrence in Arctic snow.130 It seems that PFAS are the greatest in the spring and summer seasons, which could be attributed to increased photochemical reactions that enhance the atmospheric oxidation of volatile precursors into PFAS.130 Interestingly, although long-chain PFDA and PFUnDA are commercially limited, their occurrence in the High Arctic could suggest their production via atmospheric oxidative reactions.130 Those oxidation pathways are supported by association study. For instance, the oxidation of 8
:
2 FTOH could be attributed to the strong positive correlation between PFOA and perfluorononanoic acid (PFNA).130 For PFDA and PFUnDA, which showed near-identical correlation, their shared precursor appears to be 10
:
2 FTOH.130 It seems that atmospheric oxidation is the dominant mechanism driving the transport and deposition of PFAS in the Arctic. In a study conducted in North Greenland, higher levels of neutral PFAS were revealed in the summer as compared to late winter seasons, in which it was suggested that re-emission processes from snowpack are a secondary source of PFAS after LRAT.53
The major atmospheric sink of FTOHs in the atmosphere is OH radicals, which was shown to react primarily with the alpha-CH2-group adjacent to the hydroxyl of FTOH.144 Although Cl atoms have been shown to be roughly 15 folds more reactive with FTOHs than OH radicals, their occurrence in the troposphere seems to be low.144 This notion explains why transformations with Cl atoms are considered minor atmospheric sinks for FTOHs. FTOH appears to perform LRAT, reaching remote regions, due to its estimated atmospheric lifetime of 20 days.144
Much of the literature has revealed that the reaction between Cl atoms and CF3(CF2)3CH2CH2OH (4
:
2 FTOH) selectively targets the alpha-CH2-group adjacent to the hydroxyl to produce C4F9CH·OHCH3.145,146 This radical subsequently reacts with O2 to form the primary product, CF3(CF2)3CH2CHO.145 Secondary oxidation products, CF3(CF2)3CHO and CF3(CF2)3CH2COOH (2H, 2H-perfluorohexanoic acid or 4
:
2-FTCA) can also be formed through peroxy radical pathways. The products reveal one of the oxidative mechanisms of FTOH into more persistent PFAS. When irradiating a mixture of a fluorinated alcohol with chlorine in the presence of NOx, results from IR spectroscopy revealed the formation of primary products, formic acid and fluorinated aldehydes (C4F9CH2CHO, and C4F9CHO), as well as residues of fluorinated organic nitrates and/or nitrites.147 As such, in the presence of NOx, C4F9CH2CHO was revealed to be a significant product of 4
:
2 FTOH oxidation,147 but not the only one, unlike that in the absence of NOx.145
In agreement with the aforementioned studies, through IR spectroscopy, the Cl-initiated oxidation of C8F17CH2CH2OH (8
:
2 FTOH) results in the formation of C8F17CH2CHO.148 The mechanism involves a hydrogen abstraction from the –CH2OH from the reaction between Cl and C8F17CH2CH2OH, resulting in C8F17CH2CHOH radical.148 This step is followed by the reaction between the radical and oxygen, resulting in the formation of the fluorinated aldehyde, C8F17CH2CHO.148 The formation of a perfluorinated aldehyde product from the reaction between perfluorinated alcohols with Cl atoms was also presented in the study by Solignac et al. as a primary product, but CO and CF2O appear to be produced later in the reaction as secondary products.149
It was shown that the chain lengths of FTOHs might have minimal influence on the degree of reactivity with OH radicals and Cl, particularly the reaction rate constant.144 This finding can be explained by considering that the oxidant reacts with the CH2 group rather than the carbon–fluorine chain. However, perfluorinated acid products of Cl atom-initiated oxidation of FTOH in the air with low levels of NOx vary with the chain length of the reactant FTOH.150 For instance, 8
:
2 FTOH appears to be a precursor for the production of PFNA, PFOA, pFHpA, PFHxA, PFPeA, PFBA, PFPrA, and TFA, while 6
:
2 FTOH is a precursor for all the acids, except for PFNA and PFOA.150
The formation of C7F15COOH (PFOA) from longer chain FTOH appears to be environmentally significant due to its high persistence and stability. Simulation has shown that the rate of PFOA formation from FTOH degradation is 0.88 Gg per year (ref. 151) which is roughly estimated to be 15% of the total PFOA global source flux.151 PFOA is one of the PFCAs that could be formed from the oxidative pathway of 8
:
2 FTOH, which primarily reacts with OH radicals.92 This initial reaction results in the formation of perfluoroaldehyde, which undergoes further oxidation to form C8F17C(O)O2 and C8F17O2 radicals.92 Subsequent reactions with HO2 and CH3O2 result in the formation of PFCAs, including PFOA and PFNA.92 Significantly, levels of PFOA appear to be higher in remote regions than source locations since the concentration of NOx is higher in the latter.92 The dependence of the PFOA levels on NOx concentration is attributed to the reaction between C8F17O2 and NO that competes with the reaction producing PFOA.92 This pattern has also been discussed152 by Yarwood et al., claiming that the PFOA yield is dependent on the rates of C8F17O2 with NO and RO2. For instance, the comprehensive air-quality model with extensions showed the lowest PFOA yields, in July, over the Ohio Valley, a NOx abundant region.152
Quantum chemical calculations by Sun et al. were performed153 to investigate the OH-induced oxidative degradation process of n
:
2 FTOH. Abstraction of H atoms from the alpha-CH2-group adjacent to the hydroxyl was revealed to be thermodynamically favored process.153 The thermodynamic barrier was also found to slightly increase with carbon chain length.153 The increased stability of the C–F bond was revealed to be attributed to the high Gibbs free energy barrier of F-abstraction by OH.153 In fact, the strength of the C–F bond is a well-established concept in the literature.154,155 This resistance to defluorination attributes to the highly stable nature of the oxidation products. Consistently, Altarawneh & Dlugogorski utilizing a model compound (CF3CF2CH2CH2OH) to represent atmospheric oxidation of FTOH,156 identified the same initial Hydrogen abstraction step, forming the CF3CF2CHCH2OH radical.156 Following the abstraction, the radical reacts with oxygen to form CF3CF2CH(OH)CH2OO, which after unimolecular elimination of HO2 produces the aldehyde intermediate CF3CF2CH2CHO.156 Further oxidation of the aldehyde produces CF3CF2CH2C(O)O2, which reacts with HO2 to produce PFCA.156 Plumlee et al. suggested a reaction pathway for the formation of FOSAs and PFOA from the degradation of N-EtFOSE through OH oxidation and N-dealkylation, a form of indirect photolysis.157 Blanco et al. also showed that the reactions of fluoroacetates with Cl in the atmosphere contribute to the formation of fluoroacetic acid through a structural rearrangement of the ester moiety with a five membered ring intermediate.158 Those studies show the role of photooxidation processes in the formation of more persistent forms of PFAS.
:
2 FTOH > EtFOSE > 10
:
2 FTOH > 6
:
2 FTOH.46 This trend was associated with volatility, where less volatile compounds could associate better to particles.46 However, an exception to this trend appears to be 8
:
2 and 10
:
2 FTOH as 8
:
2 showed greater particle association even though it is more volatile, which could be attributed to experimental variability.46
The main contributors to PFCAs in the atmosphere are the oxidation of fluorinated precursors and point source emissions from industrialization and consumerism.159 The low volatility and increased functionalization of PFAAs result in their high affinity to the particulate phase rather than the gas phase.159 PFOA and PFBA had the highest levels, suggesting that these compounds could be more effectively partitioned in the particulate phase.159
The illustrated spectrum (Fig. 10) visually summarizes the atmospheric partitioning behavior of volatile and ionic PFAS based on their functional groups and volatility. As depicted, neutral precursors predominantly exist in the gas phase due to their higher volatility and lower particle affinity. In contrast, more functionalized or ionic compounds show a stronger tendency to associate with atmospheric particles, due to their lower volatility and greater sorption potential. This spectrum captures the continuum of phase distribution, providing a conceptual overview of the behavior discussed throughout the literature based on functionalization and chain length.
The functionalization effect was observed in a study conducted in the marine atmosphere extending from the Japan Sea to the Arctic Ocean.52 Fluoroalkyl sulfonamidoethanols (FASEs) possessed the highest affinity for particles, roughly 26%, followed by fluoroalkyl sulfonamides (FASAs), FTOHs, and fluorotelomer acids (FTAs), with 1.8%.52 FASEs possess the least volatility as they contain both sulfonamide and hydroxyl groups, inducing hydrogen bonding with the particulate phase.52 In a study conducted in Germany, FTOHs were also found to be the most prevalent in the gas phase as they exhibit high volatility.83 Similarly, the influence of the functional group on particle-associated fraction was also identified in a study of the Canadian Arctic atmosphere.20 The particle-associated fraction decreased as follows: FOSEs (25%), PFOSA derivatives (9%), and FTOHs (1%),20 consistent with observations by Karaskova et al. who reported that volatile PFOSA derivatives and FOSEs are abundant in the gas phase.160 Moreover, in samples collected over the Gulf of Mexico, Shoeib et al. revealed that the highest particle-phase fraction was that for EtFOSE (42%), followed by 8
:
2 FTOH (26%), 10
:
2 FTOH, and MeFOSE (15%).142 Ethyl-substituted compounds, NEtFOSE, NEtFOSA, also tend to exhibit higher particle association than their methyl-substituted counterparts.61
Within the FTOH homologous series, particle association generally increases with chain length, with short-chain FTOHs such as 4
:
2 and 6
:
2 occurring almost exclusively in the gas phase and longer-chain compounds such as 8
:
2 and 10
:
2 showing slightly greater particulate fraction.161 Tian et al. proposed that as the chain length increases, stronger binding to particles is exhibited, raising the particle–air partitioning coefficient since longer chains exhibit a greater octanol–air partitioning coefficient.162 This trend was also suggested by multiple other studies in current atmospheric PFAS literature.20,26,101,163,164 However, ultra-short-chain PFCAs such as TFA and PFPrA may deviate from this trend because their small size and functionalization alter their partitioning behavior.162 PFOSA derivatives, FOSEs, and PFDS appear to be predominantly found in the gas phase, while PFOS are strongly particle bound.165 Compared to longer PFCAs, PFOA appears to exist more in the gaseous phase.165 Similarly, PFOA and PFNA have been detected in the gas phase, revealing greater ability for LRAT.25 Shorter chain PFCAs appear to be prevalent in the particulate phase, as they are well-adsorbed to mineral ions.25
When considered collectively, perfluorinated compounds (PFCs) often show greater adsorption to coarse than fine particulate matter, suggesting that coarse PM may act as an important atmospheric carrier.99 However, perfluoroalkyl acids tend to associate distinctly to fine and coarse PM. PFUnDA tends to be mostly associated with fine PM due to its low volatility, whereas PFOS, PFHxS, PFHpA tend to mostly exist in coarse PM as they are more volatile than other PFAAs.166 PFOA appears to exhibit a bimodal distribution as it can exist in protonated or deprotonated forms, thereby altering its sorption characteristics.166 Longer chain PFCAs and FTOHs appear to associate well with fine PM,167 similar to the previous finding on the association of PFUnDA with fine PM.166 It was also revealed167 that the sorption of 6
:
2 and 8
:
2 FTOH could be controlled by the presence of organic matter, whereas that of ionic PFAS could be related to mineral components that induce electrostatic interactions.
In addition to physiochemical properties, meteorological conditions also influence PFAS distribution and partitioning.168 For example, temperature and humidity were identified as important factors affecting phase partitioning and regional distribution of PFAS.67 Higher temperatures tend to increase the volatility of PFAS, increasing their occurrence in the gas phase.82 For instance, 6
:
2 FTOH concentrations gradually increased from 9.4 pg m−3 to 20 pg m−3 with rising temperatures near the equator.82 Temperature dependent variations were also studied by Li et al. revealing that short chain PFAS are highly sensitive to temperature due to their increased volatility, while long-chain PFAS are less sensitive to temperature fluctuations as they are more particle-bound.169 However, another study showed that atmospheric levels of PFAS were insignificantly correlated with temperature and latitude.48 This finding could be attributed to specific factors that govern the atmosphere in the study area, where long range atmospheric transport (LRAT) could play a more important role than temperature-related factors.48 Remarkably, a temperature-dependent partitioning of FOSEs seems to affect their detection in the particulate phase.170 FOSEs appear to have a greater particulate affinity at lower temperature than higher ones.170 This could imply that higher temperatures could increase the atmospheric mobility of FOSEs. However, FTOHs and PFOSA derivatives are mostly found in the gas phase,170 increasing their transport in the atmosphere and their potential degradation into more persistent PFAS. In another study, it was shown that as temperatures decreased, the partitioning of MeFOSE and EtFOSE to the particulate phase increased, but FTOH did not show any temperature dependent trend.46 In regard to perfluoroalkyl acids, they appear to be most abundant in colder seasons than warmer ones.74 For instance, PFOS levels were shown to be the highest in the winter and the lowest in the summer.74 This could be attributed to increased volatility in the summer, increased emission sources in winter, or winter temperature inversions that could trap pollutants near the surface.74
Arp et al. showed that the gas/particle partitioning constant varied significantly with relative humidity for polar compounds, but not for nonpolar compounds.171 This type of contrasting relative humidity dependence of partitioning between the different compounds supports the dual-phase sorption mechanism.171 The water-insoluble organic matter phase, which is independent of relative humidity, strongly induces the partitioning of nonpolar compounds.171 However, the polar compounds significantly partition into the mixed-aqueous phase, which depends on relative humidity.171 The variation in relative humidity for ionic PFAS has also been indicated by Kim et al., in which PFAAs predominate in the aqueous phase when the relative humidity exceeds 40%.172 At lower relative humidity levels, the gas-phase fractions increase, with long chain PFAAs existing predominantly in that phase under drier conditions.172 Much of the literature agrees that relative humidity is negatively associated with concentrations of PFAAs173,174 as water molecules could slow down the oxidation of PFAAs.175 However, higher PFAS concentrations have been temporarily revealed during precipitation events as liquid water droplets can act as PFAS carriers.169 Following the rainfall, the levels of particle-phase PFAS decrease via scavenging, while an increase is observed in the concentration of gas-phase PFAS as some PFAS volatilize back into the gas phase from wet surfaces or rain droplets.169
When developing a model to represent the gas-particle partition coefficients of neutral PFAS, the sensitivity of four input parameters affecting gas deposition flux was tested, including wind speed, concentration, temperature, and Henry's law constant.176 Among those four parameters, wind speed was revealed to be the most sensitive parameter for the flux with 60.9% variance for 8
:
2 FTOH.176 Wind speed could also affect the formation and enrichment of SSA. In the Atlantic Ocean, field measurements showed that PFAAs can be enriched in SSAs by over 100
000 times compared to seawater concentrations.177 Field measurements conducted in the Southern Ocean, characterized with high wind speeds, also show SSA enrichment factors between 522 and 4690.178 Those findings underscore the role of wind-driven processes on PFAS partitioning.
Research on PFAS partitioning is important to understand their multiphase chemistry and interactions within different atmospheric components. Further research should focus on two key aspects that are limited in the literature. Firstly, there is a need to further investigate sorption patterns onto fine and coarse particulate matter to expand our understanding of PFAS interactions with natural and anthropogenic emissions. Secondly, more laboratory and field studies should be conducted to explore partitioning under different meteorological conditions, which could help inform atmospheric PFAS models.
In tropical and sub-tropical regions, broader atmospheric PFAS sampling in Africa, Latin America, and the Middle East is urgently needed to close geographic knowledge gaps. While certain monitored regions display low PFAS concentrations, largely influenced by local meteorological conditions, elevated levels are observed in areas with intensive industrial activity, particularly subtropical industrial hubs. This lack of data restricts understanding of PFAS cycling in high-precipitation environments, where intense wet deposition and rapid atmospheric processing may significantly influence environmental distribution. Future research should also investigate PFAS cycling in rainforests, which serve as major atmospheric sinks and biodiversity hotspots.
While ongoing progress is being made towards understanding PFAS deposition in the atmosphere, further research could investigate the role of fog in deposition and improve monitoring programs to include short-chain PFAS and replacement compounds to avoid underestimating total deposition fluxes in coastal and mountainous environments. Moreover, standardized units to report the flux such as ng per m2 per day should be promoted to enable better comparability of deposition fluxes across the different regions. Finally, event-based and seasonal sampling should be incorporated rather than relying solely on long-term averages to capture the variability of deposition along with peak fluxes.
Moreover, volatile precursors such as FTOHs demonstrate sufficient lifetimes to undergo long-range atmospheric transport, ultimately degrading into more persistent PFAAs. Phase behavior is dictated by several factors including functionalization and chain length. However, the role of environmental variables, such as temperature, humidity, pressure, and aerosol composition, in shaping sorption patterns should be further investigated through modeling, controlled laboratory experiments, and fieldwork. Moreover, atmospheric transformation pathways are necessary to investigate, particularly in underrepresented and remote regions, influenced by LRAT. Methods such as isotope tracking and laboratory kinetics should be employed to tackle existing knowledge gaps regarding PFAS atmospheric lifetimes, source attribution, and re-emission processes from snowpacks and marine aerosols.
Policies could tackle stricter emission control in industrial centers and enhance global agreements on the production, use, and phase-out of PFAS to protect vulnerable remote ecosystems such as the polar regions. In North America and Europe, elevated levels were detected, despite continuous restrictions, highlighting the importance of monitoring and control. It is also necessary to implement more harmonized international monitoring standards to tackle PFAS pollution in East Asian industrial centers. The current shift to short-chain PFAS is also a major issue due to their increased environmental persistence and toxicity. Consequently, governments should fund research into the toxicity and environmental fate of short-chain PFAS and phase-out their use in consumer and industrial products. In addition, routine monitoring programs should be expanded to include neutral precursors and newly introduced replacement compounds, rather than focusing only on regulated legacy PFAS. A broader class-based regulatory approach may also be needed to prevent the continued substitution of restricted PFAS with structurally similar alternatives that retain high mobility and persistence.
Footnotes |
| † Now at Department of Chemistry, University of California, Irvine, California 92697, United States. |
| ‡ Both authors contributed equally to this review. |
| This journal is © The Royal Society of Chemistry 2026 |