S. K.
Nayak
a,
M.
Amela-Cortes
a,
M. M.
Neidhardt
b,
S.
Beardsworth
b,
J.
Kirres
b,
M.
Mansueto
b,
S.
Cordier
a,
S.
Laschat
*b and
Y.
Molard
*a
aUniversité de Rennes 1 – CNRS UMR 6226 “Institut des Sciences Chimiques de Rennes”, Campus de Beaulieu, CS 74205, 35042 Rennes Cedex, France. E-mail: yann.molard@univ-rennes1.fr
bInstitute of Organic Chemistry, University of Stuttgart, Pfaffendwaldring 55, 70569, Stuttgart, Germany. E-mail: Sabine.Laschat@oc.uni-stuttgart.de
First published on 6th January 2016
The ternary polyionic inorganic compound Cs2Mo6Br14 and 18-crown-6 ethers bearing two o-terphenyl units have been combined to design phosphorescent columnar liquid crystalline hybrid materials. The obtained host–guest complexes are very stable even at high temperatures. Depending on their surrounding atmosphere, these hybrids switch reversibly from a high-to-low luminescence state and show a very stable emission intensity up to 140 °C.
The dibenzo[18]crown-6 derivatives CEn with two lateral tetraalkyloxy o-terphenyl units, as well as the Cs2Mo6Br14 cluster ternary salt, were prepared according to the reported procedure with conforming analytical data.10,12
This TMC salt was chosen for its high thermal stability, a prerequisite for developing new classes of clusters containing thermotropic hybrid materials. Complexes were obtained by mixing 1 equivalent of Cs2Mo6Br14 dissolved in acetone with 4 equivalents of CEn dissolved in dichloromethane. The reaction mixture was then stirred at 50 °C for 14 hours. After evaporation of solvents, the residue was taken up by dichloromethane to remove, by filtration through a microfilter, any traces of unreacted TMC, and heated under a high vacuum to yield the respective dry complexes (2CEn:Cs)2Mo6Br14 = CLn. Their purity was verified by elemental analysis (ESI). 1H NMR experiments performed on free CEn and their respective complexes CLn did not reveal many changes due to the Cs+ complexation within the crown ether cavity (ESI,† Fig. S1 and S2). Only a slight upfield shift of signals corresponding to the methylene groups of the crown ring from 4.26 ppm to 3.96 ppm was observed upon complexation. This shift could be due to (1) a small decrease in the dihedral angle of the OCH2CH2O fragment upon ion complexation to accommodate the bulky Cs+ cation and (2) an electric field caused by the presence of the salt. It is noteworthy that the complexation of smaller ions such as K+ within the macrocyclic cavity induced the opposite effect.11 As previously observed,9 it is mandatory to maintain a Cs:CEn ratio of 1:2 in order to maintain a full homogeneity of the cluster salt/CEn complex.
The LC properties of hybrids were studied by polarized optical microscopy (POM), differential scanning calorimetry (DSC, ESI,† Fig. S4–S6) and, small and wide angle X-ray scattering (SAXS, WAXS, ESI,† Fig. S7–S14), the results of which are shown in Table 1. All complexes show enantiotropic LC phases extending over a wide temperature range. This behaviour largely contrasts with the native CEn precursor, for which LC phases were observed at lower temperatures and over narrower ranges. However, the increase in the mesophase stability as compared to the parent CEn precursor is similar to that encountered when soft anions such as iodide or bridging anions such as hexafluorophosphate or thiocyanate are used to counterbalance the positive charge of a potassium cation embedded within the crown cavity.11 This unexpected result is of particular interest as host–guest complexes between the small 18-crown-6 cavity and the sterically demanding Cs+ cation are usually supposed to be weak. It could eventually be attributed to the polyionic character of the TMC salt and the strong interactions existing between the complexed Cs+ and [Mo6Br14]2− dianion which insure a better stability of the supramolecular assemblies upon heating. Surprisingly, the DSC thermogram of CL8 reveals, upon heating, the formation of two LC phases, whereas upon cooling, only one first order transition corresponding to the isotropic-to-LC phase transition is observed (ESI,† Fig. S5). Fig. 1 shows the optical fan-shaped focal conic textures observed upon cooling for all samples, which are typical indicators of columnar mesophases. Heating CL8 from 100 °C up to 160 °C did not lead to any noticeable change in the observed textures. Irradiating the samples with UV light illustrates their excellent homogeneity thanks to the well-known red NIR emission of TMC (vide infra). The same experiments performed at 200 °C also reveal a very good homogeneity showing that the interactions between the crown centre and Cs+ cations are strong enough to maintain the integrity of the complex even at very high temperatures (ESI,† Fig. S3).
Transition | T/°C | ΔCp/ΔH | Mesophase | Lattice spacing/Å | |
---|---|---|---|---|---|
a In kJ mol−1 K−1. b In kJ mol−1. c Observed on cooling from the isotropic state; Cr: crystalline state; Colr: columnar rectangular; Colh: columnar hexagonal; I: isotropic state. | |||||
CL9 |
Cr → Colr
Colr → I |
129.8
150.8 (148.7)c |
7.28b
2.36b |
Colr
131 °C p2mm |
a = 66.3
b = 44.4 h = 4.0 Z = 1 |
CL8 |
g → Colr
Colr → Colh Colh → I |
91.6
146.6 164.4 (162.2)c |
0.43a
2.54b 2.50b |
Colr
119 °C p2mm Colh 150 °C p6mm |
a = 62.5
b = 43.8 h = 4.5 Z = 1 a = 35.5 h = 4.5 Z = 1 |
CL7 |
g → Colr
Colr → I |
96.8 (96.9)
159.2 (147.9)c |
0.141a
2.19b |
Colr
127 °C p2mm |
a = 63.1
b = 43.0 h = 4.4 Z = 1 |
Fig. 1 Polarized Optical Micrographs of (a) CL9 (T = 150 °C), (b) CL8 (T = 163 °C) and (c) CL7 (T = 150 °C) under white light (top) and UV irradiation (bottom). |
SAXS and WAXS patterns recorded at 127 °C, 119 °C and 131 °C for CL7, CL8 and CL9 respectively, contained sharp and intense reflections in the small angle region. We first analysed the XRD data, to investigate possible lamello-columnar packing, examples of which were independently reported by Donnio, Ziessel and Marcelis for metallomesogens,13 donor–acceptor-triads,14 side-chain LC polymers15 or triazines with pendant triphenylenes.16 We first checked whether sharp Bragg reflections indicating a smectic order were present for complexes CLn. However, neither characteristic layer reflections in the SAXS diffractogram nor the second halo in the wide angle region were visible. Thus, a lamello-columnar phase or a coexisting lamellar and columnar packing could be ruled out.
Hence, the indexation of observed patterns allowed the identification of a rectangular columnar phase with p2mm symmetry for the three complexes (see Tables S1–S4, ESI,† for a full indexation). All WAXS patterns contained a broad and large signal around 4.4 Å arising from the fluid-like behaviour of the molten alkyl chains and from the stacking of the aromatic units within the columns confirming the liquid crystalline nature of all complexes. For CL8, additional measurements were performed at 150 °C to characterize the unexpected second mesophase detected via DSC upon heating. Three signals with reciprocal d-spacings in the ratio 1:1/√3:1/2 were observed in the SAXS pattern and are in good accordance with the formation of a 2D hexagonal lattice with a p6mm symmetry (Colh). In this case, the unit cell parameter (a = 35.5 Å) was calculated by looking at the position of the most intense scattering signal assigned to the (10) reflection. A comparison of previously published XRD data for metal-free crown ether CE1117 with those for CLn (Table 1) revealed that the symmetry of the Colr lattice changed upon complexation. While the lattice parameter a remains relatively unaffected, i.e. 66.1 Å (CE11) vs. 66.3 Å (CL9) despite the difference of 2 CH2 units in the side chain, the b values almost doubled from 25.1 Å (CE11) to 44.4 Å (CL9). Halos were in a similar range (4.6 Å vs. 4.0 Å). To rationalize these results, we propose that the nanocluster, because of its bulkiness, cannot be accommodated within the c2mm lattice of CEn, resulting in a p2mm lattice with an elongated b axis, so that the cluster fits in the centre of the unit cell and is surrounded by 4 stacks of crown ethers CE9 with an intracolumnar distance of 4 Å (Fig. 2). This results in a height of 12 Å for the unit cell and the (1:4) cluster/CE9 stoichiometry is maintained. In that case the inorganic moieties volumic fraction is around 9 vol%. For the corresponding Colh phase of CL8, the observed a value should allow a hexagonal packing of the discotic crowns CE8, while each Mo6Br142− unit is encapsulated by three crowns and leads to a volumic fraction of 22 vol% for Cs2Mo6Br14.
Fig. 2 Proposed packing models of CLn compounds in the Colr (top, n = 7–9) and Colh (bottom, n = 8) mesophase. |
As expected, the emission properties of [Mo6Br14]2− are retained within the hybrid materials (see ESI,† Fig. S15).18 The photoluminescence spectra (λexc = 380 nm) show a broad and intense band extending from 550 nm up to 950 nm. The influence of the hybrid nanostructures on the inorganic emitter emission was investigated by temperature-dependent luminescence studies. Samples were heated up to the isotropic state and slowly cooled to reach a nanostructured glassy or crystalline state at 25 °C prior to measurements. The phosphorescence signals were collected at every degree upon heating (see the ESI,† Fig. S16 and S17). As previously reported,19 if the emission intensity variation upon heating is only due to an increase of non-radiative deactivation processes, it should follow an exponential law of the type: I(T) = I0exp(−A/T) where A is constant and I0 the emission intensity at a given temperature. Thus, reporting ln(I/I300) = f(1/T) should give a straight line and this is what is observed for Cs2Mo6Br14 (Fig. 3). Surprisingly, increasing the temperature from 25 °C up to 140 °C does not have much effect on the ability of the hybrid materials to emit light as an emission intensity loss of only less than 10% was recorded (the intensity loss at 140 °C is about 77% for Cs2Mo6Br14 in its powder form). At higher temperatures, the obtained curves significantly deviate from the straight line with a similar behaviour for CL7 and CL9. The separation of the clusters from each other by isolating triangular arrays of crown ethers might be the reason for the increased luminescence intensity of CL8 in the high temperature Colh phase as compared to the low temperature Colr phase. Presumably, the crown ethers act as an isolating matrix for luminescent clusters, making these hybrids attractive alternatives with regards to polymers for applications requiring temperatures around 100 °C.20 Thus, the columnar nanostructures have a strong influence on the emissive ability of hybrids despite the isotropic nature of the inorganic emitter. Let us emphasize that such unprecedented high stability of the emission intensity vs. temperature is particularly rare and has never been reported so far for TMC or TMC-containing hybrid materials.
Fig. 3 Evolution of luminescence intensity at 700 nm with temperature for Cs2Mo6Br14 (diamond), CL9 (triangle), CL8 (circle) and CL7 (square). Inset: Zoom of the high temperature area for hybrids. |
As illustrated by absolute quantum yield measurements performed in an air or N2 atmosphere, the emission intensity can also be modulated by modifying the local atmosphere of the material. In all cases, a reversible and instantaneous switch from 0.05 or 0.07 in air up to 0.20, 0.26 or 0.30 in an N2 atmosphere was measured for CL7, CL8 and CL9, respectively (Fig. S18 and Video S1, ESI†). This phenomenon, which shows that these materials might be used as efficient oxygen sensors, is due to the O2 permeability of CLn and is based on the ability of the excited states of the phosphorescent metal clusters to be quenched by molecular triplet oxygen, thus creating singlet oxygen.21 Although we demonstrated recently the same effect when nanoclusters are introduced into gas-permeable polymer matrices,22 this is the first time that such behaviour is reported in a liquid crystalline material.
In conclusion, we show herein, that nanometric luminescent transition metal cluster compounds are easily integrated in a CLC hybrid material by using a supramolecular approach. In these materials, Cs+ cluster unit counter cations are complexed within the cavity of crown ether derivatives functionalized by o-terphenyl units that are well known to generate columnar liquid crystalline phases. We show that the introduction of cluster salts results in columnar rectangular phases of p2mm symmetry and that their thermal stability is largely enhanced as compared to the parent crown ether CEn. Surprisingly, a second columnar hexagonal phase was observed on heating for CL8. Luminescence studies reveal that the red NIR clusters emission stability upon heating is unexpectedly largely enhanced as compared to its precursor namely Cs2Mo6Br14. Moreover, we demonstrate for the first time that modifying the atmosphere surrounding the LC hybrids with an inert gas induces a large, instantaneous and reversible increase of its emission efficiency thanks to the good O2 permeability of the LC matrix. The columnar mesophases observed for these novel clustomesogens in combination with their luminescence properties make them promising candidates for oxygen sensors, optoelectronic or photovoltaic devices. As a further step towards such applications, the mesophase temperature ranges need to be lowered by molecular design. Work towards this goal is currently in progress.
This work has been done in the frame of the ANR Clustomesogen: ANR-13-BS07-0003-01 and a Marie Curie International Incoming Fellowship within the 7th European Community Framework Program. Both organizations are gratefully acknowledged. The authors also wish to thank Dr F. Camerel for DSC access and the Fonds der Chemischen Industrie (Kekulé fellowship for S. B.) for generous financial support.
Footnote |
† Electronic supplementary information (ESI) available: Experimental details, DSC traces, POM micrographs, SAXS and WAXS patterns, temperature dependent emission spectra, video of CL7 under irradiation alternatively in an air or inert atmosphere. See DOI: 10.1039/c5cc09110a |
This journal is © The Royal Society of Chemistry 2016 |