DOI:
10.1039/D4SD00065J
(Communication)
Sens. Diagn., 2024,
3, 799-808
Plant-on-a-chip: continuous, soilless electrochemical monitoring of salt uptake and tolerance among different genotypes of tomato†
Received
26th February 2024
, Accepted 4th April 2024
First published on 11th April 2024
Abstract
Tomatoes (Solanum lycopersicum), a high-value crop, exhibit a unique relationship with salt, where increased levels of NaCl can enhance flavor, aroma and nutritional quality but can cause oxidative damage and reduce yields. A drive for larger, better-looking tomatoes has reduced the importance of salt sensitivity, a concern considering that the sodium content of agricultural land is increasing over time. Currently, there are no simple ways of comparing salt tolerance between plants, where a holistic approach looking at [Na+] throughout the plant typically involves destructive, single time point measurements or expensive imaging techniques. Finding methods that collect rapid information in real time could improve the understanding of salt resistance in the field. Here we investigate the uptake of NaCl by tomatoes using TETRIS (Time-resolved Electrochemical Technology for plant Root environment In situ chemical Sensing), a platform used to measure chemical signals in the root area of living plants. Low-cost, screen-printed electrochemical sensors were used to measure changes in salt concentration via electrical impedance measurements, facilitating the monitoring of the uptake of ions by roots. We not only demonstrated differences in the rate of uptake of NaCl between tomato seedlings under different growth conditions, but also showed differences in uptake between varieties of tomato with different NaCl sensitivities and the relatively salt-resistant “wild tomato” (Solanum pimpinellifolium) sister species. Our results suggest that TETRIS could be used to ascertain physiological traits of salt resistance found in adult plants but at the seedling stage of growth. This extrapolation, and the possibility to multiplex and change sensor configuration, could enable high-throughput screening of many hundreds or thousands of mutants or varieties.
Introduction
NaCl, or simply “salt”, is toxic for the majority of plants, leading to oxidative damage and reduced crop yields.1–3 For tomatoes, however, there is a push and pull with salt: although more salt leads to lower yields and smaller fruits, those fruits will often have better flavor, aroma and nutritional properties, where increasing salinity increases concentrations of fructose, glucose, minerals, carotene and vitamin C.4,5 Tomatoes (Solanum lycopersicum) are a valuable crop plant, with US production having a value of around US $1.8 billion in 2022 – “heirloom” varieties are sold at a higher premium due to their superior taste and quality.6,7 Unfortunately, a drive for larger, more attractive fruits has reduced the priority of organoleptic properties, nutrition and salt tolerance during tomato production, a concern considering that the sodium content of agricultural land is increasing over time.8 Breeding with other species closely related to tomato (such as the “wild tomato” species Solanum pimpinellifolium) could increase salt and disease resistance in cultivated tomatoes, while improving their nutritional quality.9
In agriculture, electrical conductivity (EC) measurements are used to ascertain the overall ionic activity of a nutrient solution or growth medium, which can give an indication into how the crop will develop.4,10 Generally, high EC will produce tomato fruits that are highly flavored, but with reduced fruit sizes and yield. Excess salinity can decrease water availability to the plant due to reduced osmotic pressure across the roots, which in turn reduces xylem transport of water and solutes from the roots to the fruits. The specific ionic content of the medium is also important to consider, where high EC water that contains an excess of Na+ ions may prevent uptake of macronutrients, such as K+, due to competing transport.11
In some countries, the volume and quality of water used in irrigation may be reduced, leading to higher EC values and therefore lower yield.12 In other areas, tomatoes are often grown covered in greenhouses or under plastic-covered tunnels to prevent frost damage, and where soilless systems are used, the reuse of irrigation water may reduce costs but can lead to increasing EC of the water over time.4,6,13 Across the world, arable land is also vastly outsized by marginal land (land that is unsuitable for farming), where salt-affected land forms a large proportion of marginal land.14 In these high-salinity conditions, the use of cultivars with increased salt resistance would be beneficial and could potentially recover these marginal lands for agricultural use. While varieties exist with a range of sensitivities to salt, S. lycopersicum is generally not considered resistant to NaCl. It has been proposed that wild tomato genotypes, such as S. pimpinellifolium, may be good candidates for gene donation to improve salt tolerance in commercial cultivars.9
Beyond its purely agricultural value, S. lycopersicum is also of great importance to the biological field as a model plant. The tomato has features (including flesh fruits and compounds leaves) not present in other model plants, such as Oryza sativa (rice) and Arabidopsis thaliana. S. lycopersicum is also closely related to other members of the Solanaceae family, which includes potato, eggplant, tobacco, and is studied for its response to biotic (pathogenic) and abiotic (such as light, salinity and temperature) stresses.15,16 Beyond being an essential part of photosynthesis, light is known to affect many plant processes, including growth, nutrient uptake and salt tolerance.17,18
Currently, there are no simple ways of measuring or comparing salt tolerance or sensitivity between plants, and instead a holistic approach must be taken. When looking at differences in salt tolerance between tomato genotypes, researchers often measure variation in Na+ transport from outside the root into the shoot, correlation between concentration of Na+ and leaf area, Na+ accumulation in old leaves compared to new, and leaf [K+]/[Na+] ratio.19,20 Typically, these four “physiological characters” may only be established destructively, relying on dried plant mass or by taking physical samples, and single measurement cannot capture complex, time-dependent plant behavior. As these characteristics could be useful for plant breeding programs, finding methods that collect rapid information in real time could improve the understanding of salt resistance in the field. Salt stress can produce visual and physical symptoms that range in severity, such as yellowing, leaf drying and rolling, tip whitening, wilting, premature senescence, cessation of growth and death.21 These measurements are often not quantitative, however, and there is a need for quantitative methods and technology that can relieve the current “bottleneck” in phenotyping of different (engineered) varieties.22,23 Imaging methods can provide rich time-dependent information, such as positron emission tomography (PET), which has been used to monitor the transport of 22Na+ in various plant species.24,25 These methods often require expensive specialized equipment, however. The quality of data can also depend on optimum setup and optical inference.26 Electrochemical sensors have previously been used in plants to measure salt stress, although sensors designed to be inserted into the stem may not be compatible with small, weaker plants and can cause stress responses of their own.27
In this work, we share our research into the uptake of salt by tomato plants, utilizing our whole-plant, soilless monitoring platform TETRIS (Time-resolved Electrochemical Technology for plant Root In situ chemical Sensing). TETRIS comprises low-cost, 2D screen-printed electrochemical sensors located underneath the roots of living plants to measure the local chemical environment. Due to the importance of sodium by tomatoes for both the quality of the fruits and for salt sensitivity, we used TETRIS to monitor the uptake of NaCl in S. lycopersicum via electrochemical impedance measurements. As light is another key factor in the growth of plants and uptake of ions, we also investigated the uptake of NaCl and KNO3 in plants grown under dark conditions compared to a standard light–dark schedule, where plants grown in dark generally showed higher uptake. Finally, as different varieties of tomatoes and related species can have differences in their tolerance to salt, we have utilized TETRIS to elucidate differences in Na+ uptake between commercial cultivars of S. lycopersicum and compared these to the salt-resistant wild tomato species S. pimpinellifolium. By demonstrating higher uptake of NaCl in sensitive plants, we demonstrate TETRIS could be used to show salt resistance of mature plants at the seedling stage of growth.
Results and discussion
General experimental setup of TETRIS
TETRIS consisted of a measurement chamber and a disposable sensing module (Fig. 1A).28 The chamber comprised a transparent acrylic lid and silicone base with water reservoir, allowing the plant to photosynthesize whilst maintaining a constant humidity. Screen-printed electrodes on polyester transparency sheet were affixed to a raised platform, placed into the measurement chamber and connected to a potentiostat (PalmSens 4 by PalmSens BV, Netherlands). The use of two eight-channel multiplexers allowed for the simultaneous monitoring of up to 16 sensors. To detect the chemical environment around the roots of living plants, all experiments were performed where plants were grown on chromatography paper and placed onto the sensing module. Firstly, seeds were washed and germinated on wet tissue before transferring onto discs of chromatography paper. The area of growth of the chromatography paper was defined by hydrophobic wax barriers formed by a HPRT MT800 thermal transfer printer. The discs with germinated seeds were then placed in enclosed boxes and supplied with water from a reservoir for a set number of days, before being removed from the box and placed onto the sensing module to perform experiments.
![image file: d4sd00065j-f1.tif](/image/article/2024/SD/d4sd00065j/d4sd00065j-f1.gif) |
| Fig. 1 Setup, characterization and experimental use of TETRIS. (A) Schematic showing the setup of TETRIS, including production of sensors and preparation of seedlings. (B) Calibration of the impedance sensor in TETRIS for [NaCl], with insert showing sensor design. (C) By measuring the impedance of a filter paper disc with tomato seedlings (“Heinz 1350”, 20 plants, 7 days growth, green signal), we could monitor the uptake of NaCl upon addition, compared to filter paper disc with no seedlings (black signal) or paper disc with seedlings, but addition of deionized water (cyan signal). (D) The rate of uptake of NaCl by tomato seedlings (“Heinz 1350”, 20 plants, 7 days growth) could be found by plotting log(Z) against time and fitting a line from the point of lowest impedance after addition of treatment and the point at which the impedance returns to the initial average value (if at all), with 5% tolerance. The rate of uptake, kuptake, was set as the gradient of the line. | |
We used two screen printed electrodes made of conductive carbon ink (Sun Chemical) to measure electrical impedance of the solution in the paper disc between the two electrodes. The electrodes were both 30 mm × 6.25 mm and separated by 55 mm. Impedance measurements were at a set frequency of 2 kHz, with amplitude of 0.25 Vhalf-wave (RMS) and at 0 V d.c. As electrical impedance decreases with increased salt concentration due to higher number of charge carriers (Fig. 1B, NaCl calibration curve), we have used this sensing setup to monitor the uptake of ions by living plants.
When a disc of chromatography paper wetted with deionized water was placed on the impedance sensor, the initial electrical impedance was relatively high (>50 kΩ) due to a lack of ions. Upon addition of NaCl solution (Fig. 1C), the impedance dropped (to around 10–20 kΩ) due to an increase in the number of charge carries in the paper. An increase in impedance (around 5–10 kΩ) occurred over tens of hours due to the added ions diffusing through the solution in the paper, but it remained lower than the initial baseline impedance (before salt was added). When living plants were present on the paper discs, the impedance dropped when salt was added by a similar amount, but, over tens of hours, the impedance steadily rose back up to the baseline level. This effect is attributed to the uptake of ions from the solution in the paper by the seedlings present on top. We have previously observed a similar effect in kale seedlings for multiple salts with a range of ions (including sodium salts, heavy metal salts and nutrients), and TETRIS is not limited to just measuring changes in [NaCl].28 To compare this observed uptake between experiments, the rate of uptake, kuptake, was calculated by taking the gradient of the slope in the log(Z) vs. t plot (Fig. 1D).
Continuous monitoring of uptake of ions in the root environment of tomato seedlings
We used TETRIS to measure the uptake of added NaCl by tomato seedlings with different experimental conditions. Initially, we compared uptake between different numbers of tomato seedlings (“Heinz 1350”) grown in the same way on paper discs, where we found a greater number of plants showed greater rates of uptake of NaCl (30 μL, 0.02 M) from zero to ten plants (Fig. 2A). This is unsurprising, due to the greater surface area of roots available to take up ions with a greater number of plants. Greater increase was not observed between ten and twenty plants, presumably due to all the added ions being taken up by ten plants, although twenty plants were used subsequently to ensure high levels of uptake. Weighing the mass of these different numbers of plants also showed that greater rate of uptake corresponded to greater mass, for both fresh mass (Fig. S1A†) and dry mass (Fig. 2B).
![image file: d4sd00065j-f2.tif](/image/article/2024/SD/d4sd00065j/d4sd00065j-f2.gif) |
| Fig. 2 Uptake of ions measured in S. lycopersicum “Heinz 1350” under different experimental conditions. (A) kuptake for NaCl (addition of 30 μL, 0.02 M) generally increased with number of tomato seedlings (7 days post germination: n = 3). This corresponded to dry mass of the seedlings after the experiment (B). (C) There was an increase in kuptake for NaCl (addition of 30 μL, 0.02 M) with age of plants (20 plants), with large deviation in kuptake (2 days post germination: n = 6; 3 days: n = 5; all others: n = 3). (D) Plants grown in a dark environment, on average, had a larger kuptake for both NaCl and KNO3 (addition of 30 μL, 0.02 M) than plants grown in a standard light–dark schedule, however this result did not yield statistically significant differences (KNO3, dark: n = 4; all others: n = 3). Lighting conditions, therefore, appear not to affect salt or nutrient uptake rates. | |
When monitoring uptake with seedlings of different ages, we observed an increase in average kuptake with increasing age of the plants from 2 days to 10 days post-germination for addition of NaCl (30 μL, 0.02 M). The deviation between samples was large, however, and while the fresh mass of the samples increased with age, the dry mass was not notably different (Fig. S1B and C†). It is likely that the samples did not have large differences in the total root area, despite their difference in ages, resulting in similar uptake amounts.
S. lycopersicum has been utilized to study the effects of light stress for both high and low light levels. Low light levels are associated with higher risk of pathogenic infection, and the color and intensity of light can lead to accumulation of specific metabolites.16 Steroidal glycoalkaloids, which are toxic to humans, were found to have greater accumulation under red, blue and fluorescent light sources, although the underlying mechanisms are unclear.29 High intensity light has been found to induce nonuniform pigmentation patterns of anthocyanins (pigments that can aid with protection from UV and high intensity light), and low intensity light did not activate genes for anthocyanin biosynthesis at all.30 Higher light intensities are also linked to higher uptake of nutrients (K and P) in tomato plants and increased biomass.18
We grew tomato seedlings as before but placing the growth box in the dark for the entire growth period. We then compared the uptake of NaCl and KNO3 (both 30 μL, 0.02 M) to tomatoes grown in the dark compared to those grown in the standard laboratory light–dark schedule (approximately 8 h dark and 16 h light per day). Interestingly, despite previous research suggesting that greater light leads to higher nutrient uptake, we did not observe a statistically significant difference in uptake of either NaCl or KNO3 for plants grown in different lighting conditions, when using a two-sample T-test (NaCl: t(6) = −1.1209, p < 0.05; KNO3: t(7) = −0.96669, p < 0.05). We did, however, find that the plants grown in the dark were notably taller (Fig. S1D,† average height of 5.8 cm) compared to plants grown in standard lighting conditions (average height of 4.5 cm). This difference in height was also found to be statistically significant when using a two-sample T-test (t(8) = −4.5018, p < 0.05). Conversely, however, these dark-grown plants had a lower average fresh and dry mass than those grown in standard lighting conditions and visibly were more yellow and unhealthy (Fig. S1E–G†).
This phenomenon of plants grown from seed in full darkness being taller and more yellow is well documented.31,32 Under a standard light–dark schedule, once germinated seedlings have reached the surface of the soil and are exposed to light, they will produce hormones to signal the stem to reduce elongation. For plants grown in total darkness, the stems continue to grow as if they are still underground to reach the surface before all the nutrition provided by the seed is depleted. Based on our measurements, these processes, however, do not impact the uptake of NaCl or KNO3 and hence we found no statistically significant correlation between lighting condition and uptake rate in young tomato seedlings.
Observing differences in uptake of NaCl in varieties and species of different salt tolerance
Most varieties of S. lycopersicum are sensitive to moderate concentrations of NaCl (in the range of hundreds of mM) at various stages of lifecycle, including germination, seedling, and fruit production.33,34 Early phenotyping of behaviors resulting from salt stress, while not able to provide information on fruit yield and adult growth, could be utilized for initial screening of the salt sensitivity of new cultivars. Seedlings are also far more susceptible to high salt levels due to the lack of older tissue, such as leaves, that mature plants use to separate excess salt to protect the rest of the plant.35,36
We investigated the NaCl uptake in both S. lycopersicum and a wild species of tomato, S. pimpinellifolium, commonly known as the “currant tomato” and known to have a higher salt tolerance compared to the normal tomato.9 Six cultivars of S. lycopersicum were selected due to their commercial availability: five have had their sensitivities to salt previously established in a study by Gharsallah et al. (mildly tolerant: Heinz 1350; sensitive: Marmande, Oxheart, Rio Grande, Saint Peter);21 one variety, “Moneymaker”, has been involved in many studies, with conflicting results on the salt sensitivity of the cultivar.9,19,37 Two varieties of S. pimpinellifolium were selected (Golden Currant, Rote Murmel), and although their specific salt tolerances have not been previously studied, S. pimpinellifolium is considered to have a higher salt tolerance, with one study suggesting a higher tolerance than the tomato variety “Moneymaker”.9
The observed rate of uptake of NaCl (kuptake) for each variety at the same age (7 days) is shown in Fig. 3A, against the average dry mass for each variety and their tolerance to NaCl. Although the average dry mass of the two S. pimpinellifolium varieties was significantly different than the average dry mass of all the S. lycopersicum varieties (Fig. S2A,† one-way ANOVA (f(7,16) = 102.7781, p < 0.0001)), average dry mass was not shown to be strongly correlated with kuptake for the different varieties, with an adjusted r2 of only 0.14255 (Fig. S2B†). We did find, however, significant pairwise differences of kuptake when comparing different varieties using one-way ANOVA (Fig. 3Bi, f(7,68) = 9.8205, p < 0.0001) and a Tukey–Kramer HSD post-hoc test (chosen due to the uneven number of samples of each variety). Both wild tomato varieties showed significant difference in kuptake compared to all four of the sensitive varieties of tomato. The sensitive Oxheart variety showed significant difference compared to both the mildly tolerant Heinz 1350 variety and the unknown-tolerance variety Moneymaker. When grouping the different varieties into categories for their sensitivity to NaCl (tolerant, mildly tolerant, sensitive, uncertain), we also found significant difference between the sensitive varieties and the other categories (Fig. 3Bii, one-way ANOVA (f(3,72) = 18.4951, p < 0.0001) followed by Tukey–Kramer HSD post hoc test). No visual changes were observed in the salt-sensitive seedlings over others, but as the amount of salt added was below the concentration usually considered to induce saline stress, this is unsurprising. There were also no visual differences between the different varieties of S. lycopersicum before treatment.
![image file: d4sd00065j-f3.tif](/image/article/2024/SD/d4sd00065j/d4sd00065j-f3.gif) |
| Fig. 3 Rate of uptake of NaCl by different tomato and wild tomato varieties. (A) kuptake for each variety of tomato and wild tomato plotted against the average dry mass for each variety at the same age (7 days). Colors indicate classification of sensitivity to salt (purple = tolerant; cyan = mildly tolerant; green = sensitive; black = uncertain sensitivity). Error bars show one standard deviation (moneymaker, Saint Peter: n = 8; Golden Currant, Rote Murmel: n = 9; Heinz 1350, Oxheart, Rio Grande: n = 10; Marmande: n = 12). (B) Statistical analysis (one-way ANOVA followed by a Tukey–Kramer HSD post hoc test) showed differences in kuptake between some varieties (i) and sensitivities to NaCl (ii). Confidence diamonds show mean uptake, 95% confidence interval and number of data points, and letters show categories with or without significant difference. | |
Mechanisms for salt tolerance, Na+ uptake and Na+ transport are complex, although it is generally agreed that salt-sensitive plants display greater Na+ uptake or accumulation.38 Transport of Na+ from the external root solution to the plant shoot can vary between genotypes.19 Na+ flow is largely unidirectional, travelling from the roots into the shoot through the relatively fast-moving flow in the xylem. After entering the shoot, Na+ is unlikely to return to the roots via the phloem, therefore, Na+ accumulates elsewhere in the plant, such as leaves.39 In some salt resistant species, Na+ transport from the roots to the shoot is reduced in the first place – instead, Na+ is transported from the basal roots to the distal roots, where Na+ is then transported back out into the surrounding solution. Salt sensitive species can also show increased transport of Na+ from the roots into the shoot, suggesting higher Na+ uptake and upwards transport may be an indicator of salt sensitivity.24
We observed higher overall uptake of NaCl in tomato varieties known to be more sensitive to salt, and lower overall uptake by the salt-resistant wild tomato compared to the standard tomato. By showing this relationship, there appears to be a link between NaCl uptake in the seedling stage and the behavior to salt stress in the mature stage. This suggests that TETRIS could prove useful in estimating the salt tolerance of tomato varieties at a very young age, reducing the time taken to test for salt sensitivity by weeks. It is also likely that the wild tomato seedlings exhibited a lower amount of uptake due to their reduced size, as suggested in our earlier experiment comparing different ages of plants; younger plants had both lower fresh mass (Fig. S1B†) and amount of uptake of NaCl (Fig. 2C). The wild tomatoes at an age of 7 days post germination had both a similar fresh mass and amount of uptake of NaCl to Heinz 1350 tomato seedlings at an age of 3 days, as shown in Fig. S2C,† suggesting both age, mass and genetic makeup play a role in the uptake of salt.
Conclusions
With this work, we demonstrate our ability to study the effects of physical conditions (e.g., age of plants and light conditions) and biological differences on the uptake rate of ions (NaCl and KNO3), using the low-cost soilless electrochemical platform, TETRIS. Our main thesis with the work presented here was whether it is possible to ascertain the salt sensitivity or tolerance of a plant by differences in its uptake of NaCl, in line with physiological traits already studied when looking at salt tolerance.19 Not only have we observed significant differences between both species and varieties in uptake, but these differences in rates of uptake of seedlings correspond to the salt sensitivities of the adult plants, suggesting that TETRIS could be used to predict salt resistance. This extrapolation could be useful for screening many hundreds of phenotypes or mutants and picking only the most promising for further experimentation.
The main challenge TETRIS faces is that it currently has only been utilized for young seedlings. Younger plants, however, are more difficult to interface with electrical and electrochemical sensors, due to the fragility of the plant and the weightiness of most sensors, and so TETRIS provides a valuable position for monitoring seedlings. In the majority of experiments, we have grown seedlings on filter paper, an artificial growth environment without sufficient support for older roots. TETRIS consists of low-cost, highly customizable parts made via screen-printing and 3D printing and can be easily adapted to different sizes and formats. We have previously shown that TETRIS can be adapted for use in agar, commonly used in plant experiments for Arabidopsis thaliana.28,40 An impedance sensor can be embedded into the agar growth medium and monitor as ions are taken up by plants. Theoretically, TETRIS would be compatible with other soilless systems, as long as there is sufficient solution in contact with the electrodes. Soil itself could be more problematic due to the complex and heterogenous geometry, although could be compatible with sufficient coverage of the sensors. The composition of soil includes nutrients and organic matter, considered potential analytes or interferents.41 The rate of uptake of certain ions may be changed by the presence of other ions and nutrients in the soil, as uptake is often controlled by osmosis, non-specific transporters, pH (H+ gradient) and charge balance, and so the measurement of these other ions and pH is important.11,42–46 pH sensors have previously been used in TETRIS to elucidate pH effects of uptake in kale.28 Ion-selective electrodes, such as for K+, Ca2+ and Na+ could be used to decouple the non-specific uptake measured by the impedance sensors in TETRIS and differentiate difference in uptake.47,48
The high customizability and suitability for high-volume manufacturing with our 2D screen-printed sensors allows the use of TETRIS in situations that elude 3D, probe-like electrochemical sensors.49,50 Sensors could be embedded into existing soilless growth containers, where the low-profile sensors would not disrupt growth. By applying sensors to the root environment of plants grown in vertical farms, which often use soilless hydroponic systems, TETRIS could be utilized to optimize lighting conditions by measuring differences in nutrient uptake or chemical responses under different light intensities and qualities.51 One of the biggest advantages of the screen-printed nature of TETRIS is compatibility with multiplexing, due to the large number of sensors that can be made low-cost (<US $0.10 per sensor). Thousands of samples with differing plant varieties, mutants or growth conditions could be run simultaneously, such as in high-throughput, agar-based optical sensing systems that already exist, where information on the chemical environment would complement visual differences of the plants.40
Materials and methods
Impedance sensor fabrication, setup and characterization
Carbon electrodes (Sun Chemical C2130925D1 conductive carbon ink (80 wt%), Gwent Group S60118D3 diluent (20 wt%)) were screen-printed onto polyester transparency sheet (Office Depot). The sensor design consisted of two identical electrodes (30 mm × 6.25 mm) separated by 5 mm. Impedance measurements (amplitude 0.25 Vhalf-wave (RMS), frequency 2 kHz, 0 V d.c.) were performed with a PalmSens 4 potentiostat and MUX8-R2 multiplexers (PalmSens BV, Netherlands). During experiments, the sensor was adhered to the base of a petri dish (55 mm diameter), placed into a measurement chamber consisting of a silicone base and reservoir of water. The sensor was connected to the potentiostat with crocodile clips and a transparent colorless acrylic lid placed over the experimental setup. Paper discs were prepared by printing a hydrophobic wax barrier (HPRT MT800) onto chromatography paper (Whatman, grade 1, 0.18 mm thickness) and heat transferred (Vevor HP230B, 120 °C, 15 minutes) to define a circular area (radius 17.5 mm, area 962 mm2). Characterization of NaCl was carried out with 1 ml solution in a paper disc on top of the sensor. The impedance was measured for at least 2 hours and the average of the impedance response recorded.
Plant growth
The following seeds of Solanum lycopersicum (tomato) were obtained: “Cuore Di Bue” (“Oxheart”, Thompson & Morgan UK), “Heinz 1350” (Chiltern Seeds Direct UK, Premiere Seeds Direct UK), “Marmande” (Just Seed UK), “Moneymaker” (Thompson & Morgan UK), “Rio Grande” (Thompson & Morgan UK), “Saint Peter” (“St. Pierre”, Sow Seeds UK). The following seeds of Solanum pimpinellifolium (wild tomato) were obtained: “Golden Currant” (Seed-Cooperative UK), “Rote Murmel” (Seed-Cooperative UK). All seeds were stirred in 30% commercial bleach for 15 minutes, rinsed in deionized water and germinated on damp tissue paper for 4 days prior to transfer onto a paper disc. The paper discs with germinated seeds were placed in a propagator box with transparent lid at a relative humidity of around 80%. Ambient light and temperature were used, cycling from around 26 °C/22 °C, day/night, and 14 hours daylight per day. The paper constantly supplied with deionized water from a reservoir with paper strips.
Salt uptake experiments
A disc with or without seedlings was removed from the growth chamber after a set number of days (7 days, unless otherwise stated) and placed onto the sensor in the measurement chamber. 100 μL deionized water was added to the paper and, after at least 3 hours, 30 μL salt solution was added to the paper through a port in the lid. To calculate the rate of uptake of the salt, an initial baseline impedance was found by taking the average impedance of the first 2 hours. The time when the impedance was lowest after addition of salt was found and a logarithmic curve of the form log(Z) = t·kuptake + c was fitted from this time onwards, where Z is impedance, t is time, kuptake is gradient and the rate of uptake of salt, and c is the intercept. Where the curve meets the initial baseline impedance, with a 5% tolerance, the gradient kuptake was found for the curve up to that point. Where the line did not reach the initial baseline, a curve was plotted until the end of the experiment time and the gradient kuptake was found.
Drying plants
Plants were removed from the chromatography paper discs and placed into polystyrene weighing boats. They were dried in an oven at 40 °C for at least 16 hours and cooled to room temperature before weighing.
Author contributions
P. C. and F. G. conceived the structure of the manuscript. P. C. led the writing of the manuscript and experimental work. Y. C., T. A. and Z. Z. contributed to experimental work. J. M. R. F., T. B. and F. G. contributed to the writing of the manuscript. All authors reviewed and agreed on the manuscript before submission.
Conflicts of interest
There are no conflicts of interest to declare.
Acknowledgements
The authors would like to thank the department of Bioengineering at Imperial College London. F. G. and P. C. thank the Imperial College Centre for Processable Electronics (CPE) and EPSRC (EP/L016702/1). Y. C. would like to thank the Turkish Ministry of Education and EPSRC IAA. T. A. would like to thank Innovate UK (grant reference: 10004425). F. G. and J. M. R. F. would like to thank the Bill and Melinda Gates Foundation (Grand Challenges Explorations scheme under grant number: OPP1212574 and Investment ID INV-038695). T. B. acknowledges BBSRC (BB/T006102/1) for their support. F. G. also acknowledges Agri Futures Lab and thanks the US Army (U.S. Army Foreign Technology (and Science) Assessment Support program under grant number: W911QY-20-R-0022).
References
- T. J. Flowers and T. D. Colmer, Salinity Tolerance in Halophytes, New Phytol., 2008, 179(4), 945–963 CrossRef CAS PubMed . https://www.jstor.org/stable/25150520.
- M. He, C. Q. He and N. Z. Ding, Abiotic Stresses: General Defenses of Land Plants and Chances for Engineering Multistress Tolerance, Front. Plant Sci., 2018, 9, 1771, DOI:10.3389/FPLS.2018.01771.
- G. Goet, I. Sonkar, S. Kumar, K. S. H. Prasad and C. S. P. Ojha, Effect of Salinity on Crop Growth and Soil Moisture Dynamics: A Study with Root Water Uptake Model, J. Hazard., Toxic Radioact. Waste, 2024, 28(3), 04024009, DOI:10.1061/JHTRBP.HZENG-1299.
- M. Dorai, A. P. Papadopoulos and A. Gosselin, Influence of electric conductivity management on greenhouse tomato yield and fruit quality, Agronomie, 2001, 21(4), 367–383, DOI:10.1051/agro:2001130.
- T. Watabe, Y. Nakano and D. H. Ahn, The Effect of Electrical Conductivity on Fruit Growth Pattern in Hydroponically Grown Tomatoes, Crops, 2022, 2(3), 323–335, DOI:10.3390/CROPS2030023.
- Agricultural Marketing Resource Centre. Agricultural Marketing Resource Centre Commodity Report - Tomatoes. 2023 Sep. https://indicators.extension.iastate.edu/projects/CommodityReport/marketmaker_pdf_2.php?topic=Tomatoes&geo=national [Accessed 28th September 2023].
- J. A. Jordan, The Heirloom Tomato as Cultural Object: Investigating Taste and Space, Sociol. Rural., 2007, 47(1), 20–41, DOI:10.1111/J.1467-9523.2007.00424.X.
- P. Shrivastava and R. Kumar, Soil salinity: A serious environmental issue and plant growth promoting bacteria as one of the tools for its alleviation, Saudi J. Biol. Sci., 2015, 22(2), 123–131, DOI:10.1016/j.sjbs.2014.12.001.
- W. Sun, X. Xu, H. Zhu, A. Liu, L. Liu and J. Li,
et al., Comparative Transcriptomic Profiling of a Salt-Tolerant Wild Tomato Species and a Salt-Sensitive Tomato Cultivar, Plant Cell Physiol., 2010, 51(6), 997–1006, DOI:10.1093/PCP/PCQ056.
- M. Grell, G. Barandun, T. Asfour, M. Kasimatis, A. S. P. Collins and J. Wang,
et al., Point-of-use sensors and machine learning enable low-cost determination of soil nitrogen, Nat. Food, 2021, 2(12), 981–989, DOI:10.1038/s43016-021-00416-4.
- A. Wakeel, Potassium–sodium interactions in soil and plant under saline-sodic conditions, J. Plant Nutr. Soil Sci., 2013, 176(3), 344–354, DOI:10.1002/JPLN.201200417.
- A. Malakar, D. D. Snow and C. Ray, Irrigation Water Quality—A Contemporary Perspective, Water, 2019, 11(7), 1482, DOI:10.3390/W11071482.
- D. Schwarz, A. J. Thompson and H. P. Kläring, Guidelines to use tomato in experiments with a controlled environment, Front. Plant Sci., 2014, 5, 625, DOI:10.3389/FPLS.2014.00625/BIBTEX.
- Y. Wang, Q. Lin, Z. Liu, K. Liu, X. Wang and J. Shang, Salt-affected marginal lands: a solution for biochar production, Biochar., 2023, 5(1), 1–10, DOI:10.1007/S42773-023-00219-9/TABLES/2.
- S. Kimura and N. Sinha, Tomato (Solanum lycopersicum), A Model Fruit-Bearing Crop, Cold Spring Harb. Protoc., 2008, 3(11), pdb.emo105, DOI:10.1101/PDB.EMO105.
- W. Liu, K. Liu, D. Chen, Z. Zhang, B. Li and M. M. El-Mogy,
et al., Solanum lycopersicum, a Model Plant for the Studies in Developmental Biology, Stress Biology and Food Science, Foods, 2022, 11(16), 2402, DOI:10.3390/FOODS11162402.
- F. Xiao and H. Zhou, Plant salt response: Perception, signaling, and tolerance, Front. Plant Sci., 2023, 13, 1053699, DOI:10.3389/FPLS.2022.1053699/BIBTEX.
- E. M. Almansa, A. Espín, R. María, C. María, T. Lao and E. Mar Ia Almansa,
et al., Nutritional response of seedling tomato plants under different lighting treatments, J. Plant Nutr., 2017, 40(4), 467–475, DOI:10.1080/01904167.2016.1187748.
- J. Cuartero, M. C. Bolarín, M. J. Asíns and V. Moreno, Increasing salt tolerance in the tomato, J. Exp. Bot., 2006, 57(5), 1045–1058, DOI:10.1093/JXB/ERJ102.
- J. Cuartero, R. Romero-Aranda, A. R. Yeo and T. J. Flowers, Variability for some physiological characters affecting salt tolerance in tomato, Acta Hortic., 2002, 573, 435–441, DOI:10.17660/ACTAHORTIC.2002.573.52.
- C. Gharsallah, A. Ben Abdelkrim, H. Fakhfakh, A. Salhi-Hannachi and F. Gorsane, SSR marker-assisted screening of commercial tomato genotypes under salt stress, Breed. Sci., 2016, 66(5), 823–830, DOI:10.1270/jsbbs.16112.
- R. T. Furbank and M. Tester, Phenomics – technologies to relieve the phenotyping bottleneck, Trends Plant Sci., 2011, 16(12), 635–644, DOI:10.1016/J.TPLANTS.2011.09.005.
- Y. Hu and U. Schmidhalter, Opportunity and challenges of phenotyping plant salt tolerance, Trends Plant Sci., 2023, 28(5), 552–566, DOI:10.1016/J.TPLANTS.2022.12.010.
- S. Fujimaki, T. Maruyama, N. Suzui, N. Kawachi, E. Miwa and K. Higuchi, Base to Tip and Long-Distance Transport of Sodium in the Root of Common Reed [Phragmites australis (Cav.) Trin. ex Steud.] at Steady State Under Constant High-Salt Conditions, Plant Cell Physiol., 2015, 56(5), 943–950, DOI:10.1093/PCP/PCV021.
- G. P. Ruwanpathirana, D. C. Plett, R. C. Williams, C. E. Davey, L. A. Johnston and H. J. Kronzucker, Continuous monitoring of plant sodium transport dynamics using clinical PET, Plant Methods, 2021, 17(1), 1–12, DOI:10.1186/s13007-021-00707-8.
- P. Coatsworth, L. Gonzalez-Macia, A. S. P. Collins, T. Bozkurt and F. Güder, Continuous monitoring of chemical signals in plants under stress, Nat. Rev. Chem., 2022, 7(1), 7–25, DOI:10.1038/s41570-022-00443-0.
- M. Sneha, N. A. Ravindranath, N. Murugesan and V. Jayaraman, A biosensor for monitoring of salt stress in plants, Org. Electron., 2023, 113, 106698, DOI:10.1016/J.ORGEL.2022.106698.
- P. Coatsworth, Y. Cotur, A. Naik, T. Asfour, A. S. P. Collins and S. Olenik,
et al., Time-resolved chemical monitoring of whole plant roots with printed electrochemical sensors and machine learning, Sci. Adv., 2024, 10(5), 31, DOI:10.1126/SCIADV.ADJ6315.
- C. C. Wang, L. H. Meng, Y. Gao, D. Grierson and D. Q. Fu, Manipulation of light signal transduction factors as a means of modifying steroidal glycoalkaloids accumulation in tomato leaves, Front. Plant Sci., 2018, 9, 432, DOI:10.3389/FPLS.2018.00437/BIBTEX.
- Y. Zhang, Y. Li, W. Li, Z. Hu, X. Yu and Y. Tu,
et al., Metabolic and molecular analysis of nonuniform anthocyanin pigmentation in tomato fruit under high light, Hortic. Res., 2019, 6, 56, DOI:10.1038/S41438-019-0138-2/41965093/41438_2019_ARTICLE_138.PDF.
- M. E. Reid, Growth of Seedlings in Light and in Darkness in Relation to Available Nitrogen and Carbon, Bot. Gaz., 1929, 87(1), 81–118 CrossRef CAS . https://www.jstor.org/stable/2470923.
-
S. F. Gilbert, Developmental Biology, Sinauer Associates, Sunderland (MA), 6th edn, 2000, https://www.ncbi.nlm.nih.gov/books/NBK9983/ [Accessed 12th October 2023] Search PubMed.
- J. Singh, E. V. D. Sastry and V. Singh, Effect of salinity on tomato (Lycopersicon esculentum Mill.) during seed germination stage, Physiol. Mol. Biol. Plants, 2012, 18(1), 45–50, DOI:10.1007/S12298-011-0097-Z/TABLES/2.
- K. Tanveer, S. Gilani, Z. Hussain, R. Ishaq, M. Adeel and N. Ilyas, Effect of salt stress on tomato plant and the role of calcium, J. Plant Nutr., 2019, 43(1), 28–35, DOI:10.1080/01904167.2019.1659324.
- M. Guo, X. S. Wang, H. D. Guo, S. Y. Bai, A. Khan and X. M. Wang,
et al., Tomato salt tolerance mechanisms and their potential applications for fighting salinity: A review, Front. Plant Sci., 2022, 13, 949541, DOI:10.3389/FPLS.2022.949541/BIBTEX.
- A. Khelil, T. Menu and B. Ricard, Adaptive response to salt involving carbohydrate metabolism in leaves of a salt-sensitive tomato cultivar, Plant Physiol. Biochem., 2007, 45(8), 551–559, DOI:10.1016/J.PLAPHY.2007.05.003.
- J. Cuartero, A. R. Yeo and T. J. Flowers, Selection of donors for salt-tolerance in tomato using physiological traits, New Phytol., 1992, 121(1), 63–69, DOI:10.1111/J.1469-8137.1992.TB01093.X.
- S. Chookhampaeng, W. Pattanagul and P. Theerakulpisut, Screening some tomato commercial cultivars from Thailand for salinity tolerance, Asian J. Plant Sci., 2007, 6(5), 788–794, DOI:10.3923/AJPS.2007.788.794.
- M. Tester and R. Davenport, Na+ Tolerance and Na+ Transport in Higher Plants, Ann. Bot., 2003, 91(5), 503–527, DOI:10.1093/AOB/MCG058.
- N. De Diego, T. Fürst, J. F. Humplík, L. Ugena, K. Podlešáková and L. Spíchal, An automated method for high-throughput screening of arabidopsis rosette growth in multi-well plates and its validation in stress conditions, Front. Plant Sci., 2017, 8, 291134, DOI:10.3389/FPLS.2017.01702/BIBTEX.
-
R. Weil and N. Brady, The Nature and Properties of Soils, 15th edn, 2017 Search PubMed.
- P. Mäser, M. Gierth and J. I. Schroeder, Molecular mechanisms of potassium and sodium uptake in plants, Plant Soil, 2002, 247(1), 43–54, DOI:10.1023/A:1021159130729.
- M. Griffiths and L. M. York, Targeting Root Ion Uptake Kinetics to Increase Plant Productivity and Nutrient Use Efficiency, Plant Physiol., 2020, 182(4), 1854–1868, DOI:10.1104/PP.19.01496.
- R. J. Haynes, Active ion uptake and maintenance of cation-anion balance: A critical examination of their role in regulating rhizosphere pH, Plant Soil, 1990, 126(2), 247–264, DOI:10.1007/BF00012828.
- J. Li and Y. Yang, How do plants maintain pH and ion homeostasis under saline-alkali stress?, Front. Plant Sci., 2023, 14, 1217193, DOI:10.3389/FPLS.2023.1217193/BIBTEX.
- Y. A. Othman, M. B. Hani, J. Y. Ayad and R. St Hilaire, Salinity level influenced morpho-physiology and nutrient uptake of young citrus rootstocks, Heliyon, 2023, 9(2), e13336, DOI:10.1016/j.heliyon.2023.e13336.
- H. Y. Y. Nyein, W. Gao, Z. Shahpar, S. Emaminejad, S. Challa and K. Chen,
et al., A Wearable Electrochemical Platform for Noninvasive Simultaneous Monitoring of Ca 2+ and pH, ACS Nano, 2016, 10(7), 7216–7224, DOI:10.1021/acsnano.6b04005.
- W. Gao, S. Emaminejad, H. Y. Y. Nyein, S. Challa, K. Chen and A. Peck,
et al., Fully integrated wearable sensor arrays for multiplexed in situ perspiration analysis, Nature, 2016, 529(7587), 509–514, DOI:10.1038/nature16521.
- Z. Yao, P. Coatsworth, X. Shi, J. Zhi, L. Hu and R. Yan,
et al., Paper-based sensors for diagnostics, human activity monitoring, food safety and environmental detection, Sens. Diagn., 2022, 1(3), 312–342, 10.1039/D2SD00017B.
- G. Barandun, M. Soprani, S. Naficy, M. Grell, M. Kasimatis and K. L. Chiu,
et al., Cellulose Fibers Enable Near-Zero-Cost Electrical Sensing of Water-Soluble Gases, ACS Sens., 2019, 4(6), 1662–1669, DOI:10.1021/acssensors.9b00555.
- C. E. Wong, Z. W. N. Teo, L. Shen and H. Yu, Seeing the lights for leafy greens in indoor vertical farming, Trends Food Sci. Technol., 2020, 106, 48–63, DOI:10.1016/J.TIFS.2020.09.031.
|
This journal is © The Royal Society of Chemistry 2024 |