DOI:
10.1039/D1TC01872H
(Review Article)
J. Mater. Chem. C, 2021,
9, 16078-16109
Diketopyrrolopyrrole-based single molecules in photovoltaic technologies
Received
22nd April 2021
, Accepted 19th July 2021
First published on 19th July 2021
Abstract
The increasing demand for efficient energy sources has led to the emergence of photovoltaic (PV) technologies. However, there remains a need to move them from the laboratory scale to the general market, which requires exceptional materials that provide both stability and efficiency. Among the materials currently being investigated, diketopyrrolopyrroles (DPPs) stand out due to their chemical versatility, robustness, and optoelectronic properties, especially their intense absorption in the visible and near infrared spectrum, high charge carrier mobility in conjugated systems, good crystallinity and, sometimes, low production costs. In this article, we review the most successful DPP-based single molecules applied in emerging PV technologies to date. Thus, DPP single molecules applied in organic solar cells, dye-sensitized solar cells and perovskite solar cells are presented, together with their chemical structures, photovoltaic device performance and additional information. In addition, we attempt to give some pointers for the optimization of future, DPP-containing molecular designs and to highlight the potential of these building blocks.
![image file: d1tc01872h-p1.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-p1.gif)
Desiré Molina
| Desiré Molina is assistant professor of Organic Chemistry at Universidad Miguel Hernández de Elche. She received her PhD degree from Universidad Miguel Hernández de Elche in 2016, under the guidance of Prof. Ángela Sastre-Santos, where she has remained so far. She also joined the group of Prof. Anders Hagfeldt at EPFL (Switzerland) for 12 months as a postdoctoral fellow. Her research interests concern in the development of new materials for their application in photovoltaic technologies and other electrical devices. |
![image file: d1tc01872h-p2.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-p2.gif)
Maria João Álvaro-Martins
| Maria João Álvaro-Martins received her bachelor degree (2015) and master degree (2017) in chemistry from the Universidade de Lisboa. She is currently PH.D. student in Prof. Ángela Sastre-Santos research group at Universidad Miguel Hernández. Her research is focused on synthesis and characterization of diketopyrrolopyrroles derivatives for their aplication in photovoltaic devices. |
![image file: d1tc01872h-p3.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-p3.gif)
Ángela Sastre-Santos
| Ángela Sastre-Santos is Full Professor of Organic Chemistry (2010) and Director of the Instituto de Bioingeniería at the Universidad Miguel Hernández de Elche (2019, Spain). She studied chemistry at the Universidad Autónoma de Madrid, where she obtained her PhD (1995, Tomás Torres). She was Postdoctoral fellow at the École Supérieure de Physique et Chimie Industrielles (Paris, Jacques Simon) and at the University of California, Santa Barbara and Los Angeles (Fred Wudl). She moved in 1998 to the UMH. Her research interest focuses on the synthesis of molecular and supramolecular electroactive systems with nano- and biotechnological applications. |
1. Introduction
Organic semiconducting materials are essential for improving photovoltaic technologies as their optoelectronic properties can be tuned by modifying their chemical structure, thus allowing device performance to be optimized. In order to determine the most suitable such materials, a great deal of research effort has been exerted over the years. In this sense, there are many structures on which these novel materials are based, including porphyrinoids,1,2 phthalocyanines,3 perylenediimides,4,5 and diketopyrrolopyrroles (DPPs).6 The latter are a good example of moieties that can be used to build promising semiconductors.7–10 DPPs were discovered in the 1970s by Farmum et al. as a by-product of the classical Reformatsky reaction between benzonitrile and ethyl bromoacetate.11 DPPs are π-electron bicyclic-dilactam systems that act as electron acceptors. These derivatives are characterized by excellent stability, low solubility, and an intense red colour due to the extended π-conjugation between their electron-rich and electron-deficient units, as well as strong excitonic coupling in the solid state.12,13 As such, DPPs started to be used as pigments. Due to the chemical versatility of DPPs, it was possible to synthesize other derivatives, which resulted in improvements and innovations in the pigment sector and, subsequently, in the plastics and inks industries.14 Thus, it was observed that the optoelectronic properties could be varied by changing the chemical structure of DPP, thus allowing this type of compound to be used in a large number of applications. These systems can exhibit n-type, p-type or ambipolar semiconductor behaviour and can therefore provide the desired electronic character.15 The 2,5-positions of the lactam nitrogens (Fig. 1) can be replaced by several groups, the most common being aryl, acyl and alky groups. These substitutions allow the solubility in organic solvents to be increased, whereas substitutions of the end-capping groups at the 3,6-positions perturbs the optoelectronic properties.16,17 These end-capping groups can be different aromatic groups, depending on the reagents of origin of the DPPs (Fig. 1). Other appealing properties of DPP derivatives are their intense absorption in the visible and near infrared spectrum, their high charge-carrier mobility in conjugated systems, good crystallinity and low-cost production. In addition, DPPs can show high thermal, photochemical and mechanical stability.10–19 The poor electronic character of the DPP core endows them with outstanding light-harvesting properties, while their flat structure enables significant intermolecular π–π interactions that facilitate charge mobility in organic field-effect transistors (OFETs).20,21 As such, they are attractive building blocks with wide-ranging applications, especially in the field of photovoltaic technologies and OFETs.18,22–27 In addition to these properties, DPPs also exhibit high fluorescence quantum yields in solution and in film, with a large extinction coefficient, which allows them to be used as fluorescence sensors.28–34 Singlet fission has also been described in DPP systems, both in the solid state and in solution.35,36 This property would allow the theoretical Shockley–Queisser limit to be increased from 32% to 45%, thus increasing the efficiencies of the solar devices in which they are integrated. Given the interesting properties of this type of compounds, many examples of DPP-based materials can be found in the literature, both single-molecule and polymers.9–37 Single molecules have advantages over their polymeric counterparts because of their well-defined chemical structure, easier synthesis, lower batch-to-batch variation and high open-circuit voltage.38,39 In this review article we recapitulate and discuss the latest advances in photovoltaics involving DPP-based single molecules, with an emphasis on the chemical structure of DPP-based systems, to gain an insight into the possible relationships between structure and performance in those devices in which they are integrated.
![image file: d1tc01872h-f1.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f1.gif) |
| Fig. 1 General structure of DPPs and numbering of their atoms. | |
2. DPP-based single molecules in organic solar cells
Organic solar cells (OSCs) have attracted a great deal of attention owing to their potential for obtaining lightweight and low-cost solar cells.40 Various types of OSCs are discussed herein and classified into two general groups: planar (PHJ) (Fig. 2a) and bulk heterojunction (BHJ) OSCs (Fig. 2b and 3c). Both are structurally defined by a multilayer in which each layer can be deposited using a different manufacturing technique. In a typical OCS device, the active layer is composed of a bilayer (PHJ), or a blend of the donor and acceptor counterparts (BHJ), between an anode (generally ITO) and a metal electrode (cathode).41 Interfacial layers, such as the hole-transport layer (HTL) and the electron-transport layer (ETL), are inserted between anode-photoactive and cathode-photoactive interfaces, respectively, to improve the performance and stability of the OSCs.42 To simplify the model, it is assumed that the donor absorbs the light, then an electron is excited from the donor's highest occupied molecular orbital (HOMO) to its lowest unoccupied molecular orbital (LUMO). The resulting charge transfer is efficient if the offset between the donor LUMO and acceptor LUMO is high enough to overcome the exciton biding energy, which is typically 0.1–1.4 eV, thus giving rise to electron–hole pairs or excitons. In other words, the excitons must diffuse to the donor–acceptor interface, where there is enough potential energy drop to separate these excitons into the free charge carriers, namely electrons and holes (Fig. 2-i).43 These electrons and holes are then transported to the respective electrode via the bicontinuous pathway, thereby avoiding recombination and charge capture. In this process, losses due to thermalization, absorption losses owing to spectral incompatibility, insufficient energy required for exciton splitting, i.e. Ephoton < Eband gap, which promotes a new state, trapping the electron in this state (Fig. 2-ii), and charge recombination, can occur (Fig. 2iii–v).44 As such, a low band gap material can improve device performance.45 Over the past few years, an inverted device architecture has also been established for OSCs exhibiting a relatively high environmental stability. In an inverted device, the cathode is at the bottom while the top electrode is the anode (Fig. 2c).
![image file: d1tc01872h-f2.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f2.gif) |
| Fig. 2 General structure of: (a) a PHJ cell, (b) a standard BHJ, (c) an inverted BHJ and (d) general energy diagram of the photoelectric events involved in the operation of a standard OSC. (i) Excitation of an electron between donor HOMO–LUMO and the respective diffusion from the donor LUMO to acceptor LUMO (Ephoton > Eband gap). (ii) The electron at the donor HOMO level absorbs a low-energy photon, thus promoting a new state and trapping the electron in this state. Recombination pathways are represented by downwards arrows and the green circle, where (iii) represents band-to-band recombination, (iv) trap-mediated recombination and (v) interfacial recombination. | |
![image file: d1tc01872h-f3.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f3.gif) |
| Fig. 3 Chemical structures and PCEs for (a) P1 and P2, (b) P3, (c) P4 and P5, and the acceptors PA1, PC60BM and C60. | |
Traditionally, given their excellent charge-transport performance, the electron–acceptor materials that have been extensively used in organic photovoltaics are fullerene acceptors (FAs). Representative examples include [6,6]-phenyl-C61/C71-butyric acid methyl ester (PC60BM/PC70BM) and indene-C60/C70 bisadducts (ICBAs). These FAs have the disadvantage of being expensive and having electronic levels that are difficult to modify, in addition to poor absorption in the visible region. In contrast, non-fullerene acceptors (NFAs) are often energetically tunable by way of simple chemical modifications, thus allowing them to participate in light absorption and charge dissociation. Additionally, NFAs can provide longer device lifetimes since they usually present greater thermo- and photostability. In fact, in recent years there has been a marked improvement in single-molecule-based NFAs, many of which now exceed power conversion efficiencies (PCEs) of 15%,46,47 and very recently there was a quantitative leap to PCEs as high as 18.2%.48,49 DPP-based single molecules are presented below, illustrating their chemical structure (both donor and acceptor); the structures of their non-DPP counterparts can be found in the corresponding section.
2.1. DPP-based single molecules in PHJs
PHJs were first reported in 1986 by Tang. These devices are based on two layers stacked on top of each other. Each layer comprises different organic films, one with a donor moiety and the other with an acceptor semiconductor (Fig. 2).50 In these devices, only excitons generated at a distance of 10–20 nm from the interface can reach the heterojunction. Under these conditions, the efficiency of the resulting solar cells is limited by the charge generation. In addition, the photovoltaic properties are strongly dependent on the nature of the electrodes. Although a lot of scientific work had already been published on this topic,51,52 the first example of DPP-based single molecules in PHJs would not be published until 2011. In this article, Kylberg et al. described the application of two DPP derivatives end-capped with two trifluoromethylphenyl groups (P1 and P2) together with C60 (Fig. 3) as the acceptor counterpart.53P2 contained extra vinylene bridges between the aromatic rings (Fig. 3a). The best performance was obtained with this latter after thermal annealing (PCE = 3.30%, short-circuit current density (Jsc) = 7.89 mA cm−2, open-circuit voltage (Voc) = 790 mV and fill factor (FF) = 53%, under AM 1.5G illumination (100 mW cm−2)). However, as a maximum PCE of 0.3% was achieved with P1, the structure with the most extended conjugation could be more advantageous. These derivatives were also used as electron acceptors in BHJ.54 Peng et al. designed an NFA PHJ solar cell using tetraphenyldibenzoperiflanthene (PA1, Fig. 3) as the donor and a 4-chlorophenyl-DPP (P3) as the acceptor (Fig. 3b). This work aimed to compare the results for the PHJ and a planar-mixed heterojunction solar cell (PM-HJ). PM-HJ devices contain a layer between the donor and acceptor layers. This architecture increases the exciton photogeneration, maintaining a high Voc and FF.55 With the PM-HJ architecture glass/ITO/MoO3/PA1/PA1:P3/P3/BCP/Ag they obtained a better performance (PCE = 3.20%) than with the regular PHJ one, mainly because of the improvement in JSC from 2.78 to 5.42 mA cm−2, despite presenting both lower Voc and FF. This donor/acceptor interface suggests a high interface energy gap and a relatively low saturation, thus highlighting the importance of these two parameters to generate a high Voc. In a recent study, Rooney et al., synthesized two DPP-based latent pigment donor materials (P4 and P5, Fig. 3c). Latent pigments are organic pigments with a chemically or thermally removable functionality, which induces a non-permanent dye-type solubility.56 Di-tert-butyl dicarbonate (t-BOC) protecting groups were introduced at the lactam nitrogens as this sterically bulky group can prevent the formation of π–π stacking networks and H-bonding sites, thereby the improving the solubility in common organic solvents. Once deposited, the protecting groups were removed thermally at 200 °C. These materials were combined with PC60BM (Fig. 3) as acceptor in an ITO/PEDOT:PSS/DDP-DPP-Donor/PC60BM/ETL/Al architecture.57 The best performance was obtained for P5 after thermal annealing of the entire device at 140 °C using LiF as ETL (Jsc = 2.11 mA cm−2, Voc = 375 mV, FF = 42.6%, PCE = 0.33%). As we will see below, DPP-based PHJ OSCs performed more poorly than their BHJ OSC analogues.
2.2. DPP-based single molecules in BHJs
DPP-based single molecules have been widely used in BHJ OSC devices and applied in a variety of structures. DPPs can form part of the structure of both donor single molecules and acceptor single molecules, thereby emphasizing their versatility.
2.2.1. DPP-based single molecules as donors in BHJs.
DPP-based single donor molecules will be classified here as linear donor molecules with a DPP core, linear donor molecules with a core flanked by DPPs, star-shaped DPP-based donor molecules and donor molecules based on porphyrinoids and DPPs.
2.2.1.1. Linear donor molecules with a DPP core.
These molecules have a central DPP core with different substituents attached to the aromatic rings at positions 3 and 6 of the diketopyrrolopyrrole bicycle. Due to the electronic nature of their component units, these systems are usually of the donor–acceptor–donor (D–A–D) type, with DPP being the acceptor. Since this structure induces intramolecular charge transfer, these materials absorb over a greater range of the spectrum and at longer wavelengths. Furthermore, by changing groups D and A, the photophysical properties of these systems can be tuned.58 Numerous relevant studies have been published in this regard. For instance, Patil et al. published two papers in 2016 in which they describe both symmetrical (BH1 and BH3) and asymmetric (BH2 and BH4) narrow band gap molecules, whose flanks were arranged triphenylamines (TPAs) (BH1 and BH2)59 or N-phenyl carbazoles (BH3 and BH4),60 linked via an ethyne moiety (Fig. 4a). Using PC70BM (Fig. 4) as the acceptor material, these authors obtained better results with those derivatives containing carbazole moieties after surface treatment with a methanol/acetonitrile (98
:
2) blend. Thus, BH4 showed a PCE of 5.73% vs. 5.31% for BH2, while BH3 gave a PCE of 4.65% vs. 4.06% for BH1. As such, better results were obtained with an asymmetrical structure including a carbazole heterocycle. The same authors reported a symmetrical D–π–A–π–D dipolar donor single molecule based on the donor moiety ferrocene also linked to the DPP core via an ethynyl bridge (BH5, Fig. 4b). The optimal ITO/PEDOT:PSS/BH5:PC70BM/PFN/Al device with DIO additive gave rise to a PCE of up to 6.44% with a high Jsc of 10.48 mA cm−2, a Voc of 940 mV and an FF of 64% after thermal annealing.61,62 These studies show that inclusion of the ethynyl bridge leads to a lower HOMO, and therefore to a higher Voc, as well as enhanced intermolecular π–π stacking, thus facilitating intramolecular charge transport (Table 1).
![image file: d1tc01872h-f4.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f4.gif) |
| Fig. 4 Chemical structures and PCEs of the donors BH1–BH5 and the acceptor PC70BM. | |
Table 1 Acceptor, band gap, LUMO, additive, architecture, and PV parameters for linear donor molecules with a DPP-core single molecule
Donor |
Acceptor |
LUMO (eV) |
Band gap (eV) |
Additive |
Architecturea |
J
sc (mA cm−2) |
V
oc (mV) |
FF (%) |
PCE (%) |
Ref. |
No additives were used.
|
BH1
|
PC70BM |
−3.77 |
1.72 |
DIO |
Standard |
11.16 |
850 |
56 |
4.06 |
59
|
BH2
|
PC70BM |
−3.69 |
1.84 |
DIO |
Standard |
8.88 |
880 |
52 |
5.31 |
59
|
BH3
|
PC70BM |
−3.60 |
1.73 |
Methanol/acetonitrile (98 : 2) |
Standard |
8.19 |
980 |
58 |
4.65 |
60
|
BH4
|
PC70BM |
−3.64 |
1.90 |
Methanol/acetonitrile (98 : 2) |
Standard |
9.58 |
980 |
61 |
5.73 |
60
|
BH5
|
PC70BM |
−3.64 |
1.58 |
DIO |
Standard |
10.48 |
940 |
64 |
6.44 |
61 and 62
|
2.2.1.2. Linear donor molecules with a core flanked by DPPs.
These structures include a central core, usually of an aromatic nature, linked and also more or less conjugated to the DPP moieties. Most of these systems present an A–D–A molecular structure in which the acceptor moieties are usually the DPPs. As these systems of an electronic push–pull nature, their optoelectronic properties are also customizable as in the previous group and, of course, there are numerous publications in this field. For example, Shi et al. developed a DPP–fluorene–DPP derivative (BH6, Fig. 5a) as the donor and the acceptor materials in BHJ OSCs together with the counterparts PC70BM and P3HT (Fig. 5), respectively, on both devices, thus demonstrating the ambipolar capacity of the DPP moiety. In this section we will focus on BH6 as donor. To evaluate the electron donor potential of BH6, devices with the architecture ITO/PEDOT:PSS/BH6:PC70BM/PFN/Al were manufactured. The best PV performances were obtained with a donor/acceptor ratio of 1
:
3, with a PCE of 3.26% measured under AM 1.5G illumination (100 mW cm−2) (Table 2).63 The same year, a DPP-dithienopyran (DTP)-DPP system was presented by Jung et al. (BH7, Fig. 5b). BH7 was tested as donor with PC70BM and the n-type NFA conjugated polymer N2200 (Fig. 5). These authors performed their study with the inverted architecture ITO/ZnO/active layer/MoO3/Ag, testing different donor/acceptor ratios. The best efficiencies were obtained with PC70BM when a 1
:
3 donor/acceptor ratio was used (PCE of 6.88%), while the best device performance with N2200 BH7/N2200 (1
:
2) was 4.82%, mainly because Jsc and FF were lower in the latter case (Table 2).64 Similarly, Tang et al. described a single molecule with a large hole mobility based on DPP-thieno[2,3-f]benzofuran (TBF)-DPP (BH8, Fig. 5c). The device architecture ITO/PEDOT:PSS/BH8:Acceptor/LiF/Al was used, comparing the photovoltaic performance of devices fabricated with PCBM and with the NFA N2200. The devices with N2200 as the acceptor gave better results than those with FA. The device that worked best contained a donor/acceptor ratio of 1
:
3 and 1-chloronaphthalene (CN) as solvent additive. The PCE for N2200 was 3.74%, and the best PCE for BH8/PCBM was 3.44% (Table 2).65
![image file: d1tc01872h-f5.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f5.gif) |
| Fig. 5 Chemical structures and PCEs for the DPP-core-DPP donors BH6-BH13, the donor P3HT and the acceptors N2200, SdiPBI and SdiPBI-S. | |
Table 2 Acceptor, band gap, LUMO, additive, architecture, and PV parameters for DPP-core-DPP donor single molecules
Donor |
Acceptor |
LUMO (eV) |
Band gap (eV) |
Additive |
Architecture |
J
sc (mA cm−2) |
V
oc (mV) |
FF (%) |
PCE (%) |
Ref. |
No additives were used. TSA – two step annealing. |
BH6
|
PC70BM |
−3.39 |
1.82 |
Annealed at 120 °C |
Standard |
8.08 |
890 |
45 |
3.26 |
63
|
BH7
|
PC70BM |
−3.73 |
1.52 |
— |
Inverted |
14.12 |
800 |
61 |
6.88 |
64
|
BH7
|
N2200 |
|
|
|
Inverted |
10.14 |
820 |
58 |
4.82 |
|
BH8
|
PC70BM |
−3.50 |
|
CN |
Standard |
8.20 |
740 |
56 |
3.44 |
65
|
BH8
|
N2200 |
|
|
|
|
7.60 |
820 |
60 |
3.74 |
|
BH9
|
PC60BM |
−3.73 |
1.65 |
CHCl3/DIO |
Standard |
9.70 |
890 |
56 |
4.80 |
66
|
BH9
|
SdiPBI |
|
|
|
|
6.10 |
920 |
42 |
2.40 |
|
BH9
|
SdiPBI-S |
|
|
|
|
6.70 |
960 |
53 |
3.50 |
|
BH10
|
PC70BM |
−3.47 |
1.54 |
TSA |
Standard |
11.53 |
790 |
58 |
5.28 |
67
|
BH11
|
PC70BM |
−3.45 |
1.62 |
TSA |
Standard |
10.82 |
910 |
56 |
5.52 |
67
|
BH12
|
IEIC |
−3.49 |
1.79 |
CHCl3/o-DCB |
Standard |
9.80 |
930 |
58 |
5.29 |
68
|
BH12
|
|
|
|
|
Inverted |
10.87 |
940 |
59 |
6.03 |
|
BH13
|
IEIC |
−3.46 |
1.77 |
CHCl3/o-DCB |
Standard |
8.24 |
900 |
54 |
4.00 |
68
|
BH14
|
PC60BM |
−3.46 |
1.58 |
— |
Standard |
10.92 |
828 |
61 |
5.53 |
69
|
BH14
|
IDIC |
|
|
|
|
10.16 |
811 |
58 |
4.80 |
|
BH15
|
PC60BM |
−3.43 |
1.64 |
— |
Standard |
7.32 |
830 |
57 |
3.48 |
69
|
BH15
|
IDIC |
|
|
|
|
11.30 |
820 |
59 |
5.48 |
|
BH16
|
ITIC |
−3.67 |
1.67 |
CHCl3/DIO |
Inverted |
13.35 |
850 |
63 |
7.15 |
70
|
To investigate the new NFAs SdiPBI and SdiPBI-S (Fig. 5) in BHJ OSCs, Feng et al. coupled them to a narrow bandgap donor DPP-pentacyclic bislactam-DPP (BH9, Fig. 5d). SdiPBI and SdiPBI-S derivatives had a complementary absorption (400–600 nm) to BH9. After an optimization process using the standard architecture ITO/PEDOT:PSS/Active layer/LiF/Al, BH9:PC60BM provided the best PCE of 4.80%, while the non-fullerene solar cells also exhibited promising PCEs of 2.40% and 3.50% (Table 2). The relatively low carrier mobilities of these NFAs and the large phase separation could be responsible for the lower efficiency of these solar cells.66 An interesting study in which the synthesis of two DPP-based single molecules having the structure D–A–D–π–D–A–D was described was published by Patil et al. The difference was the bridge connecting the two DPP units, which was either a double or a triple bond (BH10 and BH11, respectively; Fig. 5e). This work highlights the utility of thermal and solvent annealing treatments in improving the performance of organic devices. The authors described how, after these treatments, the efficiencies improved from 1.98% and 1.85% to 5.28% and 5.52% for BH10 and BH11, respectively (Table 2).67 Lin et al. compared two donors based on a DPP-benzo[1,2-b:4,5-b′]dithiophene (BDT)-DPP (BH12 and BH13, Fig. 5f). BH12 had linear alkylthio substituents in the thiophene units of the BDT moiety, whereas BH13 presented alkyl chains in these positions. As a consequence, significant variations in crystallinity, phase separation, charge transport and photovoltaic properties were observed, and BH12 showed higher hole mobility (1.1 × 10−2 cm2 V−1 s−1) than BH13 (3.0 × 10−3 cm2 V−1 s−1). BH12 and BH13 were subsequently applied as a donor semiconductor together with IEIC (Fig. 5) as NFA in the active layer. The best results were obtained using a binary solvent (CHCl3 and o-dichlorobenzene [o-DCB]) with the device architecture ITO/PEDOT:PSS/active layer/Ca/Al. The binary solvent leads to appropriate phase separation domain sizes, higher domain purity, better charge transport properties and better photovoltaic performance of the blended films. BH12-containing devices demonstrated better PV performance, with a PCE of 5.29%, while BH13-containing devices achieved a PCE of 4.00%. Finally, when BH12 was included in inverted architecture devices, all photovoltaic parameters were improved, reaching an efficiency of 6.03% (Jsc of 10.87 mA cm−2, Voc of 940 mV and FF of 59%).68 In 2018, Huo et al. developed two DPP-based donor materials compatible with both FA and NFA (2,2′-((2Z,2′Z)-((4,4,9,9-tetrahexyl-4,9-dihydro-s-indaceno[1,2-b:5,6-b′]dithiophene-2,7-diyl)bis(methanylylidene))bis(3-oxo-2,3-dihydro-1H-indene-2,1-diylidene))dimalononitrile) (IDIC, Fig. 6). The structure of these materials follows the same scheme as we have seen previously: two DPP units flanking a BDT donor unit. On this occasion, the intention was to determine the effect of two aromatic substituents with different degrees of conjugation extension (BH14, with a bithiophene group and BH15, with an (E)-1,2-di(thiophen-2-yl)ethane group, Fig. 6a). BHJ devices had the architecture ITO/PEDOT:PSS/Active layer/PDIN/Al (where PDIN is N,N′-bis(propylenedimethylamine)-3,4,9,10-perylenediimide, the cathode interfacial layer). The acceptors with which they were studied were the FA PC60BM and the NFA IDIC (Fig. 6a). The best PV results for BH14 were obtained with the FA (PCE = 5.53%, Jsc = 10.92 mA cm−2, Voc = 828 mV and FF = 61%), while for BH15 they were obtained with the NFA (PCE = 5.48%). The authors attribute these differences mainly to the higher absorptions of the active layers when mixtures BH14:PC60BM and BH15:IDIC are used versusBH14:IDIC and BH15:PC60BM, which led to a higher Jsc.69 Jung subsequently studied BH14 against other acceptors such as PC70BM and 3,9-bis(2-methylene-(3-(1,1-dicyanomethylene)-indanone)-5,5,11,11-tetrakis(4-hexylphenyl)-dithieno[2,3-d:2′,3′-d′]-s-indaceno[1,2-b:5,6-b′]dithiophene) (ITIC, Fig. 6) with the architecture ITO/ZnO/BH14: acceptor/MoO3/Ag. In order to extend the conjugation length in two-dimensions, in 2019 Jung et al. attached a 5-alkylthio-thieno[3,2-b]thiophene unit to the central BDT moiety (BH16, Fig. 6b). BH16 exhibited a strong intermolecular interaction in the solid state, an intense UV-vis absorption with a band gap of 1.71 eV, well matched energy levels with those of the NFA ITIC, and also good crystallinity in the film state. The best BH16:ITIC devices showed an overall PCE of 7.15% This result was one of the best for single molecules in non-fullerene BHJ OSCs.70
![image file: d1tc01872h-f6.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f6.gif) |
| Fig. 6 Chemical structures and PCEs for the DPP-core-DPP donors BH14–BH16 and the acceptors IDIC and ITC. | |
2.2.1.3. Star-shaped DPP-based donor molecules.
Star-shaped molecules are trimers, tetramers, pentamers, etc., whose constituent units are linked to a central nucleus and usually conjugated. This type of system has advantages over its linear counterparts, such as higher solubility, better film formation and less optical anisotropy properties.71
A series of star-shaped acceptor–acceptor–donor (A–A–D) compounds based on a triazine core, 2,5-thienyl DPP or 1,4-phenylene DPP as the π-conjugated bridge and tert-butyl-substituted triphenylamine (tTPA) and tert-butyl-substituted carbazole (tCz) as end groups and donor units were synthesized by Shiau et al. in 2015 (Fig. 7a and Table 3). These three donors were combined with the FAs PC60BM and PC70BM as acceptor materials. BH17 gave the best performance, exhibiting higher parameters than the other two systems when PC60BM was the acceptor (a PCE of 1.08% for BH17versus 0.79% for BH18 and 0.24% for BH19). These differences in the photovoltaic performance were due to the fact that charge transfer between tTPA and 2,5-thienyl DPP in the compound BH17 is higher than for BH18 and BH19. Additionally, the lower band-gap and broader solar-light absorption favor photo-energy conversion. When the acceptor material was changed to PC70BM, it was possible to improve the efficiencies in the devices fabricated with the same optimized conditions as for PC60BM (PCEs of 1.57%, 1.14% and 0.39% for BH17, BH18 and BH19, respectively).72
![image file: d1tc01872h-f7.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f7.gif) |
| Fig. 7 Chemical structures for the star-shaped donors BH17–BH21. | |
Table 3 Acceptor, LUMO, band gap, additive, architecture, and PV parameters for star-shaped DPP and DPP-Por donor single molecules BH17–BH36
Donor |
Acceptor |
LUMO (eV) |
Band gap (eV) |
Additive |
Architecture |
J
sc (mA cm−2) |
V
oc (mV) |
FF (%) |
PCE (%) |
Ref. |
No additives were used. TA – thermal annealing treatment. SVA – solvent vapor annealing. |
BH17
|
PC60BM |
−3.68 |
1.58 |
— |
Standard |
4.81 |
700 |
32 |
1.08 |
72
|
|
PC70BM |
|
|
— |
|
6.34 |
730 |
34 |
1.57 |
|
BH18
|
PC60BM |
−3.41 |
2.06 |
— |
Standard |
4.63 |
550 |
31 |
0.79 |
72
|
|
PC70BM |
|
|
— |
|
5.85 |
610 |
62 |
1.14 |
|
BH19
|
PC60BM |
−3.42 |
2.09 |
— |
Standard |
1.80 |
470 |
30 |
0.24 |
72
|
|
PC70BM |
|
|
— |
|
2.75 |
500 |
28 |
0.39 |
73
|
BH20
|
PC70BM |
−3.35 |
2.01 |
CF |
Inverted |
7.69 |
890 |
50 |
3.56 |
|
|
N2200 |
|
|
CF |
|
8.59 |
870 |
52 |
4.64 |
|
BH21
|
PC70BM |
−3.4 |
2.04 |
DIO |
Inverted |
7.12 |
860 |
49 |
3.22 |
73
|
|
N2200 |
|
|
DIO |
|
8.14 |
890 |
54 |
4.02 |
|
BH22
|
PC60BM |
−3.55 |
1.38 |
Pyridine |
Standard |
10.52 |
810 |
50 |
4.26 |
75
|
BH23
|
PC60BM |
−3.61 |
1.33 |
DIO |
Standard |
14.93 |
710 |
55 |
5.81 |
75
|
BH24
|
PC60BM |
−3.60 |
1.36 |
DIO |
Standard |
16.00 |
710 |
64 |
7.23 |
76
|
BH25
|
PC70BM |
−3.74 |
1.52 |
— |
Standard |
12.43 |
880 |
61 |
6.67 |
77
|
BH26
|
PC70BM |
−3.79 |
1.44 |
— |
Standard |
14.32 |
950 |
67 |
8.98 |
77
|
BH27
|
IDIC |
−3.85 |
1.37 |
TA |
Inverted |
15.46 |
710 |
56 |
6.13 |
78
|
BH28
|
IDIC |
−3.86 |
1.37 |
TA |
Inverted |
14.03 |
710 |
53 |
5.21 |
78
|
BH29
|
IDIC |
−3.87 |
1.41 |
TA |
Inverted |
11.46 |
700 |
51 |
4.08 |
78
|
BH30
|
6TIC |
−3.81 |
1.37 |
DIO+ |
|
|
|
|
|
|
|
|
|
|
SVA |
Standard |
20.44 |
800 |
74 |
12.08 |
79–81
|
BH31
|
PC70BM |
−3.90 |
1.40 |
SVA |
Standard |
15.98 |
890 |
66 |
9.24 |
82
|
BH32
|
PC70BM |
−3.72 |
1.72 |
SVA |
Standard |
14.31 |
820 |
62 |
7.27 |
82
|
BH33
|
IDT-C8 |
−3.51 |
1.30 |
SVA |
Standard |
11.15 |
710 |
65 |
5.14 |
83
|
BH34
|
Y6 |
−3.24 |
1.82 |
CN + TA |
Standard |
16.88 |
780 |
52 |
6.86 |
84
|
BH35
|
Y6 |
−3.33 |
2.02 |
DIO + TA |
Standard |
18.26 |
690 |
55 |
6.93 |
84
|
BH36
|
PC70BM |
−3.33 |
1.57 |
— |
Inverted |
5.00 |
551 |
38 |
1.04 |
85
|
Liu et al. designed two novel DPP-based 3D molecular donors (BH20 and BH21, Fig. 7b and Table 3). The FA PC70BM and the NFA N2200 were also compared in the inverted architecture ITO/ZnO/active layer/MoO3/Ag. After optimization of the active layer composition and adding CN, BH20 gave rise to PCEs of 3.56% and 4.64% with PC70BM and N2200, respectively, and BH21 yielded values of 4.02% and 3.22%, respectively. These differences in BH20/acceptor devices were due to the fact that the mixtures with N2200 generated higher quantum efficiencies than those based on PC70BM, as evidenced by the incident photon to current efficiency (IPCE).73
2.2.1.4. Donor molecules based on porphyrinoids and DPPs.
One very successful approach has involved the combination of DPP moieties with porphyrinoid (Por) macrocycles74 to obtain efficient donors, which is why these systems have been given their own subsection. Thus, Liang et al. synthesized tetrafuranyl and a tetraselenyl DPP-Por-DPP systems using triple bonds as connectors between the units (BH22 and BH23, Fig. 8a). The aim of this work was to determine how the different chalcogen atoms influence the PV performance of the devices by comparing these two molecules with a previously described tetrathienyl analogue (BH24, Fig. 8a) in the standard architecture ITO/PEDOT:PSS/donor:PC60BM/PFN/Al.75BH23 gave better PV parameters than BH22 when 0.6% DIO was added (PCE of 5.81%, Jsc of 14.93 mA cm−2, Voc of 710 mV and FF of 55%; Table 3), although it was possible to significantly improve the performance of BH22 by replacing the DIO with 1 vol% of pyridine (PCE of 4.26%, Jsc of 10.52 mA cm−2, Voc of 810 mV and FF of 50%). Nevertheless, BH24 continued to hold the series record with a PCE of 7.23%. The active layer containing BH23 presents a more favorable morphology than for BH22, although BH24 provides a better morphology than either, with a smaller downhill driving force for electron transfer and exciton dissociation.76 A further interesting example is the work of Bucher et al., who designed and synthesized two single molecules comprising a boron-dipyrromethene (BODIPY) core linked to two Por by phenyl (BH25) or thienyl units (BH26) and also linked to two DPP units (Fig. 8b). The BHJ devices were designed using the following architecture: ITO/PEDOT:PSS/donor:PC70BM/PFN/Al. Upon optimization of the active layer after solvent vapor annealing, BH26 reached a PCE of 8.98% (Jsc of 14.32 mA cm−2, Voc of 950 mV and FF of 67%) versus a PCE of 6.67% for BH25 (Table 3). The higher values for BH26 could be related to better exciton dissociation, higher charge transport and charge mobility.77
![image file: d1tc01872h-f8.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f8.gif) |
| Fig. 8 Chemical structures and PCEs for the DPP-Por donors BH22–BH35. | |
The combination of DPP-Por donors with NFA has led to the best results in OSCs for single molecules based on DPP. Thus, Hadmojo et al. fabricated devices using three different NIR-absorbing porphyrin-DPP donors and an IDIC as acceptor (BH27–BH29, Fig. 8c). The influence of the meso substituents in the porphyrin (p-octoxyphenyl (BH27), p-(2-ethyl)-hexoxyphenyl (BH28) and 5-(2-ethyl)hexylthiophenyl groups (BH29)) was analyzed. After optimization of the active layer, BH27:IDIC gave a PCE of 6.13% (Jsc of 15.46 mA cm−2, Voc of 710 mV and FF of 56%), which was higher than for BH28:IDIC (PCE of 5.21%) and BH29:IDIC (PCE of 4.08%). The side chains on the porphyrin donors modified the nanomorphologies of the BHJ devices, thus giving better PCE values to the BH27-based devices due to the more face-on preferred donor and acceptor domains.78 In 2019, Gao et al. presented the DPP-Por-DPP donor BH30 (Fig. 8d), which was studied in fullerene-free BHJ OSCs in the standard architecture ITO/PEDOT:PSS/BH30:6TIC79,80 (Fig. 9)/C60-bissalt/Ag, where C60-bissalt is the ETL. After applying a solvent annealing treatment and including DIO as additive, a record efficiency was achieved for non-tandem fullerene-free single molecule devices up to that date. The best device reached a PCE as high as 12.08% from a high Jsc of 20.44 mA cm−2, a Voc of 800 mV and an also high FF of 74% (Table 3).81 More recently, Cuesta et al. compared two Por-DPP-Por systems. In BH31, the DPP core is flanked by separate selenophene rings, while in BH32 these rings are replaced by thiophenes (Fig. 8e). The BHJ devices were fabricated with the conventional architecture glass/ITO/donor:PC70BM/PFN/Al. After solvent vapor annealing, the best performance was achieved with an overall PCE value of 9.24% (Jsc of 15.98 mA cm−2, Voc of 890 mV and FF of 66%) and 7.27% (Jsc of 14.31 mA cm−2, Voc of 820 mV and FF of 62%) for BH31 and BH32, respectively. The authors explained this difference based on the more planar conformation due to smaller lamellar stacking and π–π stacking distances, broader absorption spectrum and higher hole mobility of BH31 compared to BH32, which led to a more favorable active layer morphology for exciton dissociation and charge transport.82 Chen et al. presented a thieno[3,2-b]thiophene-functionalized DPP-Por-DPP structure (BH33, Fig. 8f), which formed part of the active layer together with the IDT-C8 acceptor. The PCE values for all small molecule OSCs increased from 0.64% to 5.14% after SVA for the standard architecture ITO/PEDOT:PSS/BH33:IDT-C8 (Fig. 9)/PDINO/Al, where PDINO is (N,N′-bis(propylenedimethylamine)-3,4:9,10-perylenediimide).83 Two star-shaped DPP-Por donors were presented very recently. Their structures include a central zinc-porphyrin with its four meso positions linked to each DPP unit via two different aromatic rings, namely phenyl (BH34) or thienyl (BH35) (Fig. 8g). These materials were studied as donors in OSCs with the acceptor Y6 (Fig. 9), with the standard architecture ITO/PEDOT:PSS/active layer/PDINO/Al. A maximum PCE of 6.86% was achieved with BH34 when 0.75 vol% CN was used as solvent additive and after a thermal annealing at 120 °C for 10 minutes. BH35 gave the best performance (PCE of 6.93%, Jsc of 18.26 mA cm−2, Voc of 690 mV and FF of 55%) using DIO as additive after a thermal annealing at 80 °C also for 10 minutes (Table 3). The geometry of both molecules was determined by theoretical calculations. A more orthogonal geometry was established for BH35. Moreover, it was found that DPP-arms were more coplanar with the thienyl linker for BH35 than in the case of BH34. The small differences in performances were attributed to these geometric characteristics, thus suggesting that the orthogonal geometry of BH35 favors the formation of additional charge pathways.84
![image file: d1tc01872h-f9.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f9.gif) |
| Fig. 9 Chemical structures and PCEs for the DPP-Pc donor BH36 and the acceptors 6TIC, IDT-C8 and Y6. | |
Other well-known porphyrinoids include phthalocyanines (Pcs). Molina et al. published a study presenting a Pc–DPP–Pc conjugate system (BH36, Fig. 9) as donor in the standard architecture glass/ITO/HTL/BH36:PC70BM/Ca/Ag, where HTL was PEDOT:PSS or MoO3. The best results were obtained with MoO3 as HTL (PCE = 1.04%, Jsc of 5.00 mA cm−2, Voc of 551 mV and FF of 38%), since PEDOT:PSS was able to protonate the donor, thus worsening the interface contact (Table 3).85
Considering the data described, the most successful approach for the design of DPP-donors is the one that includes a porphyrin in its structure. In this category, the stiffer molecules, which include triple bonds, give rise to the best photovoltaic parameters (BH26, BH30, and BH31, PCEs of 8.98%, 12.08% and 9.24%, respectively). In contrast, the 3D design of DPP-donors did not result in adequate morphologies, with a mean PCE of 2.07% and a maximum of 4.64% (BH20). Similarly, linear DPP-donor designs did not give significantly better results depending on the position of the DPP units (core or flanks). With regard to the acceptor counterparts, although there is less data, all PV parameters are higher, on average, when NFAs are used, including the above-mentioned BH30, which holds the record for this series.
2.2.2. DPP-based single molecules as acceptor material in BHJ.
The current interest in developing NFAs has already been mentioned. In this regard, DPP acceptors are strong candidates for building acceptors for BHJ OSCs due to all the properties discussed above, especially their acceptor core formed by the bilactam and their ambipolar character. Sonar et al.86 and Karsten et al.,87 in 2010, were the pioneers in the field of using DPP derivatives as electron–acceptors, which opened the door to intensive research in this area. Analogously to donors, the acceptors will also be classified here according to their molecular structure as linear acceptor molecules with a DPP core, linear acceptor molecules with a core flanked by DPPs, star-shaped DPP-based acceptor molecules and spirofluorene-DPP-based acceptor molecules.
2.2.2.1. Linear acceptor molecules with a DPP core.
The characteristics of these systems are similar to those for linear donor systems, although it is usual to find structures that combine DPPs with other electron-acceptor units, such as 1,1,4,4-tetracyanobuta-1,3-diene (TCBD), rhodanines (Rho) and perylenediimides (PDI).
TCBD is a strong electron-withdrawing unit that promotes charge transport and imparts good solubility in organic solvents due to its nonplanar structure. Patil et al. described various TCBD-DPP based compounds (BH37–BH42, Fig. 10a–f). For BH37 (mono-substituted) and BH38 (di-substituted), the TCBD was extended with triphenylamine (Fig. 10a and b). These single molecules exhibited a good thermal stability and a broad and strong absorption in the NIR region complementary to the conjugated polymer Pol-1 (Fig. 10). A PCE of 3.90% was obtained for BH37, and for BH38 the PCE value was 4.95%.88 In BH39 (mono-substituted) and BH40, N-phenylene carbazole (Fig. 10c and d) was used as end-group, with BH40 being a disubstituted asymmetric compound with ethynylene-N-phenylene carbazole as the end group on one side and a TCBD-N-phenylene carbazole on the other.89,90 After optimization of the devices using a thermal annealing treatment, the best PCEs were 4.86% and 7.19% for Pol-2:BH39 and Pol-2:BH40, respectively (Fig. 10). These different values arise as a result of a large Jsc and FF for BH40 (Table 4), related to the broader Pol-2:BH40 absorption profile and more balanced charge transport. In turn, when these authors replaced carbazole with ferrocene to give BH41 (mono-substituted) and BH40 (di-substituted), the PCE values were similar (6.44% and 6.89% for Pol-3:BH41 and Pol-3:BH42, respectively; Fig. 10e and f). According to the authors, the results obtained were similar due to the large values of Jsc and FF. Despite this, the Jsc and FF values for BH42 are slightly higher than for BH41 (Table 4)due to the better charge transport and lower lamellar and π–π stacking distance.91
![image file: d1tc01872h-f10.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f10.gif) |
| Fig. 10 Chemical structures and the best PCEs for the acceptors BH37–BH46 and the donor polymers Pol-1, Pol-2, and Pol-3. | |
Table 4 Donor, LUMO, band gap, additive, architecture, and PV parameters for linear DPP acceptor single molecules
Acceptor |
Donor |
LUMO (eV) |
Band gap (eV) |
Additive |
Architecture |
J
sc (mA cm−2) |
V
oc (mV) |
FF (%) |
PCE (%) |
Ref. |
Not reported. TA: thermal annealing. SVA: solvent vapor annealing. VD: vacuum dried.
|
BH37
|
Pol-1 |
−4.22 |
1.32 |
SVA |
Standard |
8.15 |
920 |
52 |
3.90 |
89
|
BH38
|
Pol-1 |
−4.36 |
1.28 |
SVA |
Standard |
10.21 |
860 |
56 |
4.95 |
89
|
BH39
|
Pol-2 |
−3.83 |
1.69 |
SVA |
Standard |
10.56 |
940 |
49 |
4.86 |
90
|
BH40
|
Pol-2 |
−3.81 |
1.52 |
SVA |
Standard |
13.78 |
900 |
58 |
7.19 |
90
|
BH41
|
Pol-3 |
−3.92 |
1.51 |
VD |
Standard |
11.34 |
980 |
58 |
6.44 |
91
|
BH42
|
Pol-3 |
−4.02 |
1.37 |
VD |
Standard |
12.66 |
880 |
62 |
6.89 |
91
|
BH43
|
P3HT |
−4.13 |
1.65 |
DIO |
Inverted |
5.91 |
890 |
50 |
3.28 |
92
|
BH44
|
P3HT |
|
1.67 |
DIO |
Inverted |
4.40 |
500 |
40 |
1.10 |
93
|
BH45
|
P3HT |
|
1.64 |
DIO |
Inverted |
0.51 |
140 |
25 |
0.02 |
93
|
BH46
|
P3HT |
|
1.64 |
DIO |
Inverted |
2.72 |
150 |
25 |
0.12 |
93
|
BH47
|
P3HT |
−3.79 |
1.49 |
TA |
Standard |
3.34 |
610 |
63 |
1.28 |
94
|
BH48
|
P3HT |
−3.93 |
1.48 |
TA |
Standard |
2.06 |
750 |
31 |
0.49 |
94
|
BH49
|
P3HT |
−4.17 |
1.52 |
TA |
Standard |
3.56 |
410 |
52 |
0.77 |
96
|
|
DTS(QxHTh2)2 |
−3.99 |
1.85 |
SVA |
Standard |
11.04 |
1020 |
62 |
6.98 |
97
|
|
Pol-2 |
|
|
DIO |
Standard |
12.37 |
980 |
62 |
7.52 |
97
|
BH50
|
DTS(QxHTh2)2 |
−4.15 |
1.57 |
SVA |
Standard |
12.15 |
940 |
68 |
7.76 |
97
|
BH51
|
p-DINI-(FBTTTh3)2 |
−3.74 |
1.87 |
SVA |
Standard |
13.72 |
980 |
67 |
9.14 |
98
|
BH52
|
PTB7-Th |
−3.70 |
1.60 |
SVA |
Inverted |
10.84 |
970 |
44 |
4.63 |
99 and 100
|
BH53
|
SM1:PC70BM |
−3.96 |
1.64 |
SVA |
Standard |
16.32 |
920 |
67 |
10.05 |
101
|
BH54
|
P3HT |
−3.65 |
1.66 |
DIO + TA |
Standard |
6.25 |
970 |
39 |
2.37 |
102
|
BH55
|
P3HT |
−3.74 |
1.82 |
TA |
Standard |
3.16 |
1170 |
62 |
2.30 |
103
|
BH56
|
PTB7 |
−4.18 |
1.52 |
DCB+ CN |
Inverted |
7.77 |
830 |
47 |
3.03 |
104
|
BH57
|
PTB7 |
−4.33 |
1.52 |
DCB+ CN |
Inverted |
12.10 |
810 |
51 |
5.00 |
104
|
Josse et al. designed and synthesized two materials based on phthamilides as end group with a thienoisoindigo and a DPP (BH43) bridged by acetylene moieties (Fig. 10g). The best performance for P3HT:BH43 was obtained using the inverted cell architecture (ITO/ZnO/active layer/MoO3/Ag), with DIO as solvent additive, and after a thermal annealing treatment. Thus, a PCE of 3.28% was obtained under these conditions.92 The same group subsequently studied the influence of the alkyl side chain in this kind of compound on PV performance, using BH43 as reference. The effects of the nature (linear or branched alkyl chain) and position (in the DPP and in the phthalimide) of the side chain on the optical properties and, consequently, the corresponding PV performance, was studied. The UV-vis absorption spectra recorded for solutions and films showed two types of behavior: (1) compounds BH43 and BH44 (branched chains in DPP core) arranged to form J-aggregates in the solid state; and (2) compounds with linear side chains in the DPP core (BH45 and BH46) formed H-aggregates. The authors concluded that the branched alkyl chain in the DPP favors light absorption and promotes a better phase separation with P3HT, whereas the linear chain in phthalimide improves the charge-transport properties. The efficiencies obtained this time were 1.10%, 0.02% and 0.12% for BH44, BH45 and BH46, respectively.93
A series of A1–π–A2–π–A1 single molecules (BH47–BH49), in which a thiophene and/or furan were introduced between two strong electron-withdrawing units, namely DPP (A2) and Rho (A1) (Fig. 11a and b), was reported by Eom et al.94 These authors applied these compounds as donors and acceptors in combination with PC70BM and P3HT, respectively, due to their ambipolar character. The best performance was obtained with the architecture ITO/PEDOT:PSS/active layer/LiF/Al, where P3HT:BH47 gave the highest PCE of 1.28%, exceeding the PCE obtained for BH47:PC70BM (0.92%). A PCE of 1.77% was obtained for BH48 when mixed with PC70BM (1.77%), but only 0.49% for P3HT (Table 4). In contrast, in the case of BH49, higher parameters were achieved when this compound was used as the acceptor in the active layer along with P3HT (0.77%) than with PC70BM (0.02%). When Privado et al. substituted the LiF by PFN and added DIO, the PCE for the P3HT:BH49 mixture improved to 2.16%.95 Likewise, the PCE increased to 4.17% when using Pol-2 as the donor, subsequently increasing up to 7.52% when DIO was added, with a Jsc of 12.37 mA cm−2, a Voc of 980 mV and an FF of 62% (Table 4). The higher PCE for Pol-2:BH49 was related to the broader absorption profile of the active layer, low energy loss and balanced charge transport.96 Subsequently, dicyano groups were introduced at the rhodanine moieties of the thiophene-DPP (BH50, Fig. 11b) by the same research group, who reported a comparative study between BH49 and BH50 as acceptors using DTS(QxHTh2)2 as donor counterpart. The best PCEs were obtained when the active layer was dried under vacuum (VD) instead of using the thermal annealing technique. The vacuum-dried active layer improved the FF by suppressing bimolecular recombination and enhancing charge transport. DTS(QxHTh2)2:BH50 exhibited a PCE of 7.76% with a Jsc of 12.15 mA cm−2, a Voc of 940 mV and an FF of 68%, while for DTS(QxHTh2)2:BH49 the best PCE was 6.98%. These results were attributed to the fact that BH50 blends exhibited enhanced light absorption, molecular ordering and crystallinity.97 As an evolution of this structure, the ethynyl linker was used as a bridge between the terminal dicyanorhodanine and the dithiophene-DPP core (BH51, Fig. 11c). In that study, p-DINI-(FBTTTh3)2 (Fig. 11) was used as donor because it presents good energy levels that match with the those of BH51. The SVA method was implemented again, obtaining a high PCE of 9.14% with a Jsc of 13.72 mA cm−2, a Voc of 980 mV and an FF of 67%, and this system currently holds the record for DPP-based single molecules as acceptors in OSCs (Table 4).98
![image file: d1tc01872h-f11.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f11.gif) |
| Fig. 11 Chemical structures and the best PCEs for the acceptors BH47–BH53 and the donors SM1, p-DINI-(FBTTTh3)2. | |
Combination of the DPP core with N-annulated PDIs was described by the Welch group in two studies in which the BH52 derivative (Fig. 11d) is combined with different donor polymers in the active layer (P3HT, PCDTBT, PTB7-Th and PDTT-BOBT), in the inverted architecture ITO/ZnO/Donor:BH52/MoOX/Ag. Using the SVA processing method, PCEs of up to 4.63% with a Jsc of 10.84 mA cm−2, a Voc of 970 mV and an FF of 44% could be achieved with the donor PTB7-Th (Fig. 11 and Table 4). The donor polymer PDTT-BOBT also gave good PCEs (maximum PCE of 4.47%), but the utility thereof was limited by instability because the alkoxy side chains on the polymer backbone undergo C–O bond cleavage under irradiation.99,100
Very recently, Langa et al. compared the acceptor BH49 with its analog with selenophenes (BH53, Fig. 11e and Table 4) instead of thiophenes in the structure. When applied in binary mixtures together with the donor SM1 (Fig. 11) in the standard architecture ITO/PEDOT:PSS/active layer/PFN/Al, BH53 resulted in higher PV parameters, with PCEs of 7.22% and 8.96% for BH47 and BH51, respectively, after SVA. The application of BH53 in a ternary system, in which PC70BM is the co-acceptor and SM1 is the donor, resulted in a remarkable PCE of 10.05%, mainly due to the enhancement in Jsc and FF (Table 4).101
2.2.2.2. Linear acceptor molecules with a core flanked by DPPs.
These molecules are typically of the A–D–A type, in which DPP is the A moiety.
As mentioned in the donors section, Shi et al. developed devices with BH6 as the donor and the acceptor (Fig. 5a). When using BH6 as acceptor the architecture was ITO/PEDOT:PSS/P3HT (donor):BH6 (acceptor)/PFN/Al, with D/A ration of 1
:
1. This device exhibited the highest PCE of 3.17% after thermal annealing. Similar PCEs were obtained when BH6 was used as acceptor or donor. However, although Jsc for the BH6:PC70BM mixture (8.08 mA cm−2) was higher than that for the P3HT:BH6 blend (5.35 mA cm−2), Voc for the BH6:PC70BM blend is significantly higher than that for the P3HT:BH6 active layer (1180 vs. 890 mV). Thus, due to its twisted molecular conformation, BH6 exhibited similar HOMO and LUMO energy levels to PC70BM and P3HT, thus providing a good example of the versatility of DPP-based materials.63
More interesting studies were carried out using fluorene as the core. Thus, Li et al. developed the compound BH54 (Fig. 12a), which contains a DPP end-capped with thiophene-2-carbonitrile. Given the electronegativity of this group and the conjugation with DPP, BH54 exhibited a LUMO of −3.65 eV and a narrow bandgap of 1.66 eV. The devices were fabricated using the polymer P3HT as donor material with the standard architecture ITO/PEDOT:PSS/P3HT:BH54/PFN/Al and yielded a PCE of 2.37% when DIO was added and after thermal annealing.102 This same research group replaced the fluorene moiety with a carbazole to give the compound BH55 (Fig. 12 and Table 4), which exhibited a lower PCE of 2.30%.103
![image file: d1tc01872h-f12.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f12.gif) |
| Fig. 12 Chemical structures and PCEs for the acceptors BH54–BH57 and the donor polymer PTB7. | |
Jung et al. presented two narrow-bandgap acceptors (BH56 and BH57), whose structure includes a 4,7-dithien-2-yl-2,1,3-benzothiadiazole (DTBT) central core end-capped by two DPP units (Fig. 12b). BH57 has fluorine atoms in the DTBT core, whereas BH56 does not The objective of the study was to determine the influence of fluorine on PV performance, for which devices with the inverted architecture ITO/ZnO/PTB7(Fig. 12):Acceptor/MoO3/Ag were manufactured. The best outcomes obtained using dichlorobenzene as solvent and CN as solvent additive were 3.03% (Jsc = 7.77 mA cm−2, Voc = 830 mV and FF = 30%) and 5.00% (Jsc = 12.10 mA cm−2, Voc = 810 V and FF = 51%) for BH56 and BH57, respectively. Although the Voc for BH56 was higher than that for BH57, the photoresponse of BH57 was higher, which led to a higher Jsc and a 70% higher FF (Table 4).104
2.2.2.3. Star-shaped DPP-based acceptor molecules.
Another approach has been the synthesis of star-shaped structures in order to imitate the spherical shape of the fullerene π-system,105–111 which is assumed to be capable of aligning with the donor π-plane in a three-dimensional way, thereby possibly decreasing the Coulomb barrier for charge separation due to enhanced entropic effects and enabling isotropic charge transport.112,113
In the study by Gupta et al., a tetraDPP bifluorenylidene H-shaped acceptor was designed and synthesized (BH58, Fig. 13a). BH58 exhibited good solubility and high electron mobility and thermal stability, giving a remarkable PCE of 5.42%.114 In 2016, Rananaware et al. reported a star-shaped acceptor based on tetraphenylethylene functionalized with four DPPs (BH59, Fig. 13b). The BH59 film revealed a strong absorption in the range between 540–800 nm, which matched well with the absorption of the donor P3HT (380–640 nm). The architecture of the device was ITO/PEDOT:PSS/P3HT:BH59, using DIO as solvent additive. After thermal treatment this system gave a PCE of 3.86% with one of the highest Voc values for single-molecule BHJ devices based on P3HT as donor to date (Voc = 1.18 V).115 Liu et al. reported a compound with the same backbone as BH59 with additional phenyl capping on the end of the DPPs (BH60, Fig. 13c). In addition, they also synthesized a compound with biphenyl as backbone (BH61, Fig. 13e and Table 5) in order to compare both cores. In both cases, the hole and electron mobility and PCE increased after a thermal annealing treatment. The best PCE for P3HT:BH60 was 2.49%, with a high Voc of 1.16 V, whereas the PCE for P3HT:BH61 was 1.18% (Table 5).116 The tetraphenylethylene-DPP was also used as core in the compound BH62 (Fig. 13d) reported by Sun et al., in which the dicyanovinyl (DCV) electron-withdrawing unit was introduced as end-group. This alteration led to lower frontier energy levels in BH62 compared to BH59 and BH60. In the same report, the authors also described the PV performance of the compound BH63 (Fig. 13f and Table 5), the core of which comprises spirobicyclopentadithiophene linked to four DPPs with DCV end-groups. In this case the polymer PTB7-Th was the donor. PTB7-Th:BH62 exhibited a PCE of 4.01% and PTB7-Th:BH63 4.20% (Table 5). BH63 presented a higher PCE due to the broader UV-vis absorption profile and enhanced charge transport as a result of better conjugation along the arms, exhibiting a higher Jsc (11.69 mA cm−2) than BH61 (9.89 mA cm−2) since it contributed more to the photocurrent (Table 5).117
![image file: d1tc01872h-f13.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f13.gif) |
| Fig. 13 Chemical structures and PCEs for the star-shaped acceptors BH58–BH69. | |
Table 5 Donor, LUMO, band gap, additive, architecture, and PV parameters for star-shaped and spirofluorene-DPP-based acceptor single molecules
Acceptor |
Donor |
LUMO (eV) |
Band gap (eV) |
Additivea |
Architecture |
J
sc (mA cm−2) |
V
oc (mV) |
FF (%) |
PCE (%) |
Ref. |
No additives were used. TA – thermal annealing. |
BH58
|
P3HT |
−3.84 |
1.67 |
— |
Standard |
7.74 |
1170 |
60 |
5.42 |
114
|
BH59
|
P3HT |
−3.81 |
1.72 |
DIO + TA |
Standard |
3.15 |
1170 |
62 |
3.86 |
115
|
BH60
|
P3HT |
−3.64 |
1.59 |
TA |
Standard |
4.45 |
1160 |
47 |
2.49 |
116
|
BH61
|
P3HT |
−3.61 |
1.60 |
TA |
Standard |
2.93 |
1110 |
36 |
1.18 |
116
|
BH62
|
PTB7-Th |
−3.81 |
1.59 |
|
Standard |
9.89 |
753 |
54 |
4.01 |
117
|
BH63
|
PTB7-Th |
−3.89 |
1.42 |
|
Standard |
11.69 |
697 |
47 |
4.20 |
117
|
BH64
|
PTB7-Th |
−3.90 |
2.09 |
DIO |
Inverted |
15.26 |
850 |
65 |
8.45 |
118
|
BH65
|
PTB7 |
−3.74 |
1.82 |
TA |
Standard |
15.20 |
1020 |
61 |
9.33 |
119
|
BH66
|
PBDB-T |
−3.79 |
1.95 |
DIO + TA |
Inverted |
6.42 |
1170 |
42 |
3.17 |
120
|
BH67
|
PBDB-T |
−3.74 |
1.95 |
DIO + TA |
Inverted |
5.95 |
1150 |
41 |
2.83 |
120
|
BH68
|
PBDB-T |
−3.37 |
2.04 |
DIO + TA |
Inverted |
3.04 |
930 |
36 |
1.01 |
120
|
BH69
|
PBDB-T |
−3.40 |
1.96 |
DIO + TA |
Inverted |
4.50 |
1020 |
42 |
1.93 |
120
|
BH70
|
P3HT |
−3.60 |
1.66 |
TA |
Standard |
6.96 |
1100 |
48 |
3.63 |
121
|
BH71
|
P3HT |
−3.55 |
1.69 |
TA |
Standard |
5.52 |
880 |
41 |
1.87 |
121
|
BH72
|
P3HT |
−3.57 |
1.66 |
TA |
Standard |
3.88 |
910 |
40 |
1.42 |
121
|
BH73
|
P3HT |
−3.58 |
1.72 |
TA |
Standard |
2.37 |
750 |
43 |
0.76 |
121
|
BH74
|
P3HT |
−3.56 |
1.73 |
TA |
Standard |
1.21 |
790 |
29 |
0.28 |
121
|
BH75
|
P3HT |
−3.57 |
1.72 |
TA |
Standard |
1.96 |
700 |
33 |
0.45 |
121
|
BH76
|
P3HT |
−3.51 |
1.75 |
TA |
Standard |
8.26 |
1140 |
55 |
5.16 |
122
|
|
|
|
|
— |
Inverted |
10.23 |
1110 |
54 |
6.09 |
123
|
BH77
|
P3HT |
−3.54 |
1.83 |
TA |
Standard |
4.82 |
930 |
37 |
1.67 |
124
|
BH78
|
P3HT |
−3.58 |
1.80 |
TA |
Standard |
1.10 |
810 |
37 |
0.33 |
124
|
BH79
|
P3HT |
−3.63 |
1.80 |
TA |
Standard |
1.98 |
1000 |
37 |
0.73 |
124
|
BH80
|
PTB7-Th |
−3.86 |
1.56 |
— |
Standard |
10.71 |
740 |
49 |
3.85 |
125
|
BH81
|
PTB7-Th |
−3.85 |
1.55 |
— |
Standard |
3.22 |
740 |
41 |
0.98 |
125
|
BH82
|
PTB7-Th |
−3.89 |
1.59 |
— |
Standard |
1.09 |
740 |
32 |
0.26 |
125
|
A further interesting work is a publication in Chinese in which Hu et al. present three PDI-based acceptors that use phenylDPP cores to reduce the planarity of derivatives. All these systems produce amorphous films, which is thought to favor a suitable blend morphology. The four-armed derivative BH64 displayed the best performance when blended with PTB7-Th (Fig. 13g), with a maximum PCE of 8.45%, a Jsc of 15.26 mA cm−2, a Voc of 850 mV and an FF of 65.2% (Table 5) in the inverted architecture ITO/ZnO/Active layer/MoO3/Al. The authors attributed these results to the fact that the structure with the more expanded conjugation leads to a greater molar extinction coefficient and greater electron transport mobility.118
Very recently, Jadhav et al. presented a new 3D derivative (BH65) that combines a carbonyl-bridged triarylamine core with three DPP blades (Fig. 13h). This compound was applied as NFA together with the donor polymers PTB7 and P3HT in OSCs with the standard architecture ITO/PEDOT:PSS/active layer/Ca/Al. After testing various different manufacturing conditions, it was found that the best performance was obtained with PTB7 after a thermal annealing treatment (110 °C for 5 minutes). The maximum PCE achieved was 9.33%, with a Jsc of 15.20 mA cm−2, a Voc of 1020 mV and an FF of 61%, compared with a maximum PCE of 5.62% when the donor was P3HT (Jsc = 10.20 mA cm−2, Voc = 910 mV and FF = 60%; see Table 5).119 In another very recent study reported by Sastre-Santos, Torres and Marsall et al., the synthesis of four DPP-based star-shaped single molecules having subphthalocyanine (SubPc) as central kernel bearing three DPP wings linked by an acetylene bridge (BH66, BH67, BH68 and BH69, Fig. 13i) were studied. These acceptors featured two different axial groups (4-tert-butylphenoxy or chlorine) combined with two possible regioisomers (C1 and C3). The aim of this work was to elucidate how the structural variations between the different derivatives affect their optoelectronic properties and consequently the performance of the devices. The four derivatives were applied as NFA materials together with the PBDB-T donor polymer in inverted devices with the architecture ITO/TiO2/PBDB-T:acceptor/V2O5/Ag. After DIO addition and subsequent thermal annealing, BH66 gave the best performance (PCE = 3.17%), exhibiting a remarkable Voc of 1170 mV (Jsc = 6.42 mA cm−2 and FF = 42%).120 For this reason, SubPc-DDP derivatives are high promising NFAs for application in ternary OSCs in which a high Voc is desired.
2.2.2.4. Spirofluorene-DPP-based acceptor molecules.
Spirofluorene (SF) is a basic moiety that provides non-planarity to the structures in which it is included, thereby preventing intermolecular aggregation. As some of the molecules mentioned in this section are star-shaped-DPP or linear acceptors, given the number of relevant studies found for this fashionable scaffold, we have decided to give them a subsection.
In 2015, Wu et al. developed a series of X-shaped geometries using SF as core with thiophene-DPPs linked by a single bond (BH70–BH72, Fig. 14a) and via acetylenes (BH71–BH73, Fig. 14b).121 The branched 2-ethylhexyl (EH), linear n-octyl (C8) and n-dodecyl (C12) alkyl chains were selected as substituents to functionalize the N,N-positions of the DPP moieties. When blended with P3HT, BH70 gave a PCE of 3.63%, which is higher than for the equivalent derivatives (PCEs of 1.87% and 1.42% for BH71 and BH72, respectively). These results can be explained by the lower crystallinity of BH71 and BH72. The values obtained for the compound with the acetylene bridge were lower, with PCE values of 0.76%, 0.28% and 0.45% for BH73, BH74 and BH75, respectively. This was attributed to the fact that the sp3-hybridized C-bridge blocks electron transfer from the SF core to the DPP units.
![image file: d1tc01872h-f14.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f14.gif) |
| Fig. 14 Chemical structures and PCEs for the spirofluorene-based acceptors BH70–BH82. | |
In turn, a SF core with four benzene end-capped DPP arms was developed in the study by Li et al. (BH76, Fig. 14c).122 Introduction of the benzene rings at the end positions of the DPP led to an improvement in comparison with the analog BH70 (PCE increased from 3.63% to 5.16%). Furthermore, this system also gave a high Voc value (1.14 V). P3HT:PC60BM exhibited a lower PCE and Voc (3.18% and 620 mV) than P3HT:BH76 (5.16% and 1140 mV). Moreover, an enhanced PCE of up to 6.09% was reported for the inverted architecture ITO/ZnO/PFN/active layer/MoO3/Ag by the same authors.123
Chen et al. also developed an SF-DPP with extended conjugation containing 1,2,3-trifluorobenzene (BH77, Fig. 14d), benzo[b]thiophene (BH78, Fig. 14d) and benzo[b]furan (BH79, Fig. 14d). These derivatives exhibited a red-shifted absorption compared with BH70. The best PCEs using P3HT as donor were 1.67%, 0.33% and 0.73% for BH77, BH78 and BH79, respectively. When fused rings were introduced, the solubility decreased markedly, which could affect the morphology of the active layer.124 Three single molecules were synthesized by Sun et al. based on an SF core with a variable number of thiophene-DPP arms and dicyanocinyl as end-group (BH80–BH82, Fig. 14e–g). The PTB7-Th:BH76 blend presented the highest PCE of 3.85% due to its better phase-separation morphology and multiple electronic transmission properties. The PCE for BH81 and BH82 was 0.98% and 0.26%, respectively. The 3D structure of BH82 formed a 3D charge-transport network, thus resulting in an acceptable electron-transport ability, which further leads to a higher Jsc (10.71, 3.22 and 1.09 mA cm−2 for BH80, BH81 and BH82, respectively; Table 5).125
OSC performances with DPP-based acceptors are, in general, lower than with DPP-based donors. Looking only at averages, star-shaped designs are more successful as a result of their higher photovoltaic parameters, probably because they give rise to better morphologies. However, linear designs are very promising since the record for this series belongs to one such compound (BH53). Unfortunately, there are very few data for linear molecules with DPP flanking a core. Similarly, the parameters for DPP-based acceptors that include a spirofluorene in their structure are quite low. Although the polymeric nature of the donors is predominant, any general conclusion about whether single molecules are more suitable or not could be erroneous even though the record is held by a single molecule counterpart (SM1).
As can be seen, DPP-based donors and acceptors are not among the best single molecules in the active layer of OSCs. However, in our opinion, this should not discourage researchers in the future as these are really promising photoactive molecules that offer a wide range of designs and enhancements that are yet to be discovered.
3. DPPs as sensitizers in dye-sensitized solar cells
Dye-sensitized solar cells (DSSCs) are a photovoltaic technology that first appeared in 1991 in work by Grätzel and O'Regan.126 Unlike devices that had previously introduced the concept of sensitizer, this type of device has a rough surface on which a large amount of robust dye is adsorbed. This translates into an extensive surface interaction between the different active components that make up the architecture of the device. These systems include three main components: an organic dye, a nanocrystalline semiconductor and a redox couple as mediator in an electrolyte. As an example, they exhibit the typical architecture of an n-type DSSC device using the I−/I3− redox couple in the electrolyte and TiO2 as semiconductor (Fig. 15a). Thus, these components can be arranged in different architectures, giving rise to n-type and p-type devices. In n-type DSSCs, the operating principle includes the absorption of radiation by the dye, which moves it into the excited state, from which an electron is injected into the conduction band (CB) of the nanocrystalline semiconductor (usually TiO2). The dye remains oxidized, subsequently returning to its fundamental state due to the mediator present in the electrolyte. Finally, the anode electrons move through an external circuit to reach the counter electrode, where the mediator regenerates. P-Type DSSCs (Fig. 15b), also known as inverted DSSC, typically offering lower performances as NiO has a lower hole mobility (10−8–0.141 cm2 V−1 s−1) and smaller diffusion length for holes (2–3 μm) compared with TiO2 in n-type DSSCs.127 The operating principle of a p-type DSSC includes light absorption by the sensitizer to reach its excited state, which then injects a hole into the valence band (VB) of a semiconductor (typically NiO or CuO), thereby reducing the dye, which is regenerated by subsequent reduction of the electrolyte mediator. The latter is regenerated again thanks to the flow of electrons in the external circuit. In the case of sensitizing dyes, both energy levels and electrical properties are relevant. In general, these types of systems have a donor–π-bridge–acceptor (D–π–A) structure. In this structure, the donor unit absorbs the radiation to generate the charge-separated state, from where the charge is transmitted via the π-bridge to the acceptor unit, which is usually anchored to the semiconductor via a carboxylic acid, cyanoacrylic acid, etc. In the case of p-type devices, the charge flow is the same, although in this case holes are injected into the semiconductor. It is worth mentioning that the use of a co-adsorbent agents together with the dye, the mission of which is to passivate the surface of the semiconductor and to modulate the interactions between the dye molecules, mainly to decrease recombination phenomena, is very common.128–130 Porphyrin-based dyes have shown the best performance to date, with PCEs of more than 13%.131–133 Nevertheless, due to their electronic character, DPPs are highly suitable moieties for both n-type and p-type devices, therefore they have been applied quite successfully as dyes in this technology.
![image file: d1tc01872h-f15.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f15.gif) |
| Fig. 15 (a) Scheme of an n-type DSSC device using the I−/I3− redox couple in the electrolyte and TiO2 as semiconductor, and (b) scheme of a p-type DSSC using the same electrolyte and NiO as semiconductor material. | |
The first mention in English in the literature regarding the use of DPPs in DSSCs is a patent from 2009.134 Articles describing the application of DPPs as sensitizers in DSSCs can be found since 2010.135,136 In the first published study, two non-linear DPP systems (D1 and D2, Fig. 16 and Table 6), in which the donor units are two different triarylamines, without substituents and with p-methoxy groups in the more distal benzene rings, are compared in a n-type device. A PCE of 2.68% was obtained with derivative D1 without the use of co-adsorbent. In the case of D2, a maximum PCE was achieved using chenodeoxycholic acid (CDCA). There has been extensive research into the use of DPPs as sensitizers in DSSCs since then.137–140 The most prominent examples since 2015 are discussed briefly below.
![image file: d1tc01872h-f16.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f16.gif) |
| Fig. 16 Chemical structures and PCEs for D1–D12 and DA. | |
Table 6 Electrolyte, co-adsorbent and photovoltaic parameters for dyes D1–D30
Dye |
Electrolyte |
Co-adsorbent |
J
sc (mA cm−2) |
V
oc (mV) |
FF (%) |
PCE (%) |
Ref. |
Average values are provided.
|
D1
|
I−/I3− |
No |
9.57 |
455 |
58 |
2.68 |
135
|
D2
|
I−/I3− |
CDCA |
5.49 |
423 |
59 |
1.37 |
135
|
D3
|
Co[(bpy)3]3+/2+ |
CDCA |
17.90 |
761 |
74 |
10.10 |
141
|
D4
|
I−/I3− |
CDCA |
15.28 |
698 |
69 |
7.34 |
142
|
D5
|
I−/I3− |
CDCA |
14.86 |
687 |
75 |
7.65 |
142
|
D6
|
I−/I3− |
CDCA |
15.29 |
675 |
72 |
7.46 |
143
|
D7
|
I−/I3− |
CDCA |
17.14 |
698 |
69 |
8.30 |
143
|
D8
|
I−/I3− |
CDCA |
14.60 |
639 |
72 |
6.69 |
143
|
D9
|
I−/I3− |
CDCA |
15.59 |
643 |
70 |
7.01 |
143
|
D10
|
I−/I3− |
CDCA |
12.70 |
762 |
74 |
7.20 |
144
|
D11
|
I−/I3− |
CDCA |
12.30 |
711 |
76 |
6.60 |
144
|
D12
|
[Co3+]/[Co2+] |
— |
15.60 |
797 |
70 |
8.70 |
145
|
D13
|
I−/I3−, tBP |
DCA |
19.40 |
480 |
53 |
4.90 |
147
|
D14
|
I−/I3−, tBP |
DCA |
13.60 |
680 |
66 |
6.10 |
147
|
D15
|
I−/I3− |
CDCA |
14.21 |
670 |
64 |
6.14 |
150
|
D16
|
EMI-TBC/PMII, /tBP |
— |
15.20 |
678 |
71 |
7.1 |
151
|
D17
|
I−/I3− |
CDCA |
11.01 |
513 |
61 |
3.43 |
152
|
D18
|
I−/I3− |
CDCA |
11.30 |
539 |
59 |
3.62 |
152
|
D19
|
I−/I3− |
CDCA |
0.75 |
125 |
37 |
0.03 |
154
|
D20
|
I−/I3− |
CDCA |
1.51 |
135 |
32 |
0.07 |
154
|
D21
|
[Co3+]/[Co2+] |
CDCA |
1.62 |
365 |
31 |
0.18 |
154
|
D22
|
I−/I3− |
— |
1.89 |
100 |
33 |
0.063 |
155
|
D23
|
I−/I3− |
— |
1.44 |
84 |
33 |
0.040 |
155
|
D24
|
[Co3+]/[Co2+] |
— |
2.06 |
330 |
30 |
0.205 |
155
|
D25
|
[Co3+]/[Co2+] |
— |
1.95 |
370 |
29 |
0.210 |
155
|
D26
|
I−/I3−, GuSCN, TBP |
— |
0.26 |
74 |
53 |
0.008 |
156
|
D27
|
I−/I3−, GuSCN, TBP |
— |
0.70 |
81 |
25 |
0.010 |
156
|
D28
|
I−/I3−, GuSCN, TBP |
— |
7.38 |
147 |
32 |
0.35 |
156
|
D29
|
I−/I3−, GuSCN, TBP |
— |
4.04 |
123 |
32 |
0.16 |
156
|
D30
|
PC60BM |
CDCA |
0.32 |
228 |
32 |
0.023 |
157
|
3.1. DPP-based single molecules as sensitizers in n-type DSSCs
Although we will focus on studies published since 2015, the highest PCE for an n-type DSSC sensitized with DPP derivatives was achieved in 2013 using molecule D3 in the presence of the co-adsorbent CDCA (Fig. 16b and Table 6). In that article, four asymmetric DPP derivatives that differ only in terms of the donor moiety are compared. These derivatives are studied using both computational calculations and spectroscopically and photovoltaically. A PCE of 10.10% was achieved with D3 when combined with the electrolyte Co[(bpy)3]3+/2+.141 In 2015, Ganesan et al. compared two DPP-based dyes to determine the influence of the different strength of the acceptor unit on light harvesting and the electrochemical and photovoltaic properties of DSSC devices containing CDCA. Here, the strong acceptor cyanoacrylic acid (D4) is compared with the weaker acceptor carboxylic acid D5 (Fig. 16c and Table 6). The difference in optoelectrochemical properties was found to be not significant. However, a better photovoltaic result was obtained with D5, with a Jsc of 14.86 mA cm−2, a Voc of 687 mV, an FF of 75% and a PCE of 7.65% under simulated one sun versus a PCE of 7.34% with the cyanoacrylic acid group.142 The same year, Li et al. published a paper in which they described four molecules with a D–π–A–π–A structure, with N-annulated perylenes as the donor groups (D6–D9, Fig. 16d and Table 6). These authors studied the effect of additional electron-donating substituents at a peri position of the perylene and found that the bulky 4-methoxyphenyl group attached at this peri position can reduce charge recombination and enhance Voc, thus making derivative D7 the most efficient of the four with and without CDCA. Therefore, D7 with co-adsorbent showed a PCE of 8.30% with a JSC of 17.14 mA cm−2, a Voc of 698 mV and an FF of 69%.143 Similarly, Chiu et al. synthesized and studied two DPP-based dyes (D10 and D11, Fig. 16e and Table 6) with 4,4′-ditolylaniline as the donor and cyanoacrylic acid as the acceptor and anchoring group. The objective was to elucidate how the presence of phenyl (D10) or thienyl (D11) spacers influences the photovoltaic properties of the devices fabricated in the presence of CDCA. Although D11 had a very high molar extinction coefficient at 530 nm (2.25 × 105 M−1 cm−1) and a lower bandgap, D10 demonstrated better performance (PCE = 7.20% vs. 6.60% for D11) due to its better ability to inject electrons into TiO2 as a result of its linear structure, as shown by density functional theory (DFT) calculations and femtosecond time-resolved photoluminescence data.144
A further interesting study was published by Hao et al., in which these authors described how the correct co-sensitization between red and blue D–π–A organic dyes leads to an improvement in the performance of solar cells. Thus, the blue DPP D12 was combined with the red dye DA in a 3
:
4 ratio, which resulted in an increase in PCE from 7.30% and 5.50%, respectively, separately to a PCE of 8.70% when combined, using the cobalt-based electrolyte tris(2,2′-bipyridyl)cobalt(II/III) ([Co(bpy)3]3+/2+) under AM 1.5G (Fig. 16f and Table 6).145
Shimogawa et al. designed and synthesized two low-bandgap DPP-based sensitizers that included boryl-substituted thienylthiazole moieties in the acceptor group (D13 and D14). D13 and D14 possess octyl and 2,6-dialkoxybenzyl groups on the lactam nitrogen atoms of the DPP unit, respectively (Fig. 17a and Table 6). The DPP group was introduced into the system as an enhancement to a previous prototype,146 namely the DB sensitizer. As a result of this modification, the two DPP-based derivatives have more suitable HOMO and LUMO levels with a narrower bandgap than DB. The best performance was obtained with D14 (Jsc = 13.60 mA cm−2, Voc = 680 mV, FF = 66%, and PCE = 6.10%), with deoxycholic acid (DCA) as co-adsorbent and 4-tert-butylpyridine (tBP) as additive.147 TBP in I−/I3− electrolyte solution increases the CB edge potential of TiO2, thus leading to an increase in Voc and a decrease in electronic recombination by preventing the access of I3− to the TiO2 surface.148,149 Similarly, Wang et al. reported the synthesis of two D–π–A–π–A systems (DC and D15, Fig. 17b and Table 6) with N,N-di-p-tolylanilinyl in the donor moiety. These authors studied the impact of the difluorobenzo[c][1,2,5]thiadiazole or DPP auxiliary acceptor on the photophysical and electrochemical properties and DSSC performance. The DPP-containing molecule D15 exhibited a higher Jsc due to its high molar extinction coefficient at higher wavelengths and its wider absorption spectrum, which ranges from the visible to the near-infrared region, thus generating a greater photocurrent than its counterpart. A longer electron lifetime and increased charge recombination resistance were observed for DC, thus resulting in a higher Voc. DSSC devices sensitized with D15 showed better performance (Jsc = 14.21 mA cm−2, Voc = 670 mV, FF = 64%, and PCE = 6.14%) than those containing DC (Jsc = 11.01 mA cm−2, Voc = 750 mV, FF = 71%, and PCE = 5.81%) when CDCA was used a co-adsorbent.150 Decoppet et al. developed different binary ionic liquid electrolytes based on 1-methyl-3-propylimidazolium iodide salts and also investigated the influence of adding lithium ions to the electrolyte to enhance the DSSC device performance, together with the DPP-based sensitizer D16 (Fig. 17c and Table 6). The best device exhibited a short-circuit current density of 15.20 mA cm−2, a Voc of 678 mV and an FF of 71%, corresponding to an overall PCE of 7.1%, under standard AM 1.5G illumination at 100 mW cm−2 with the electrolyte mixture EMI-TBC/PMII 1
:
1 in the presence of I2 and N-butylbenzimidazole.151
![image file: d1tc01872h-f17.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f17.gif) |
| Fig. 17 Chemical structures and PCEs for D13–D18. | |
In a recent study by Lim et al., the synthesis of blue-colored dyes featuring a DPP spacer with dimethylamine and bis(4-dibutoxylphenyl)phenylamine as donor residues (D17 and D18, Fig. 17d and Table 6) was reported, together with their spectroscopic, electrochemical and colorific properties and their application in translucent DSSCs. In the DSSCs fabricated with 5 μm-thick TiO2 photoanodes and CDCA as co-adsorbent, D17 and D18 yielded PCEs of 3.43% and 3.62%, respectively, under simulated one sun illumination.152
3.2. DPP-based single molecules as sensitizers in p-type DSSCs
As mentioned at the beginning of this section, DSSC p-type devices are generally less efficient than n-type devices since they still face many challenges. The current record was published by Perera et al. in 2015, with a PCE of 2.51% and an amazing Jsc of 7.65 mA cm−2.153 These authors used an electrolyte based on the tris(acetylacetonato)iron(III)/(II) redox couple ([Fe(acac)3]0/1−) and a perylene-thiophene-triphenylamine sensitizer (DD; Fig. 18a and Table 6). The first study of DPP-based sensitizers was published by Favereau et al. in 2013. In this paper, three diphenylDPP systems with thienyl carboxylic acid as the anchoring group and with a bromine (D19), a malononitrile (D20) or a naphthalenediimide (NDI) (D21) as acceptor moiety were compared (Fig. 18b and Table 6). All DPP derivatives were tested with I−/I3− electrolyte, but only D21 was used with [Co3+]/[Co2+] electrolyte, in this latter case obtaining the best result in the presence of CDCA, with a Jsc of 1.62 mA cm−2, a Voc of 365 mV, an FF of 31% and a PCE of 0.18%.154 These authors also presented other molecules based on diphenylDPPs with a dicarboxylated triphenylamine, an anchoring group for attachment to NiO, and bromine (D22 and D23) or NDI (D24 and D25) as acceptor group. DSSC devices were fabricated with the classic electrolyte I−/I3− and with cobalt(II/III)–polypyridine electrolytes (Fig. 18c and Table 6). Those dyes containing the NDI acceptor unit yielded higher photovoltaic performances, exhibiting larger charge separation state lifetimes than those with bromine. In addition, the devices containing cobalt(II/III)–polypyridine electrolytes showed better results.155 The same authors subsequently reported a series of four analogues with structural modifications. Thus, they replaced diphenylDPP with dithienylDPP, including the dicarboxylated triphenylamine anchoring group in D26 and D27, but replacing it with a thienyl carboxylic acid in D28 and D29, and including the NDI acceptor group also connected via a triple bond in D27 and D29 (Fig. 18d and Table 6). As result of these modifications, these derivatives exhibited higher molar extinction coefficients at longer wavelengths than their diphenyl counterparts. More importantly, these modifications led to a notable improvement in performance, achieving a PCE 0.35%, a Voc of 149 mV, an FF of 33% and a Jsc of 7.40 mA cm−2 with sensitizer D29.156
![image file: d1tc01872h-f18.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f18.gif) |
| Fig. 18 Chemical structures and PCEs for D19–D29 sensitizers for p-type DSSCs. *Maximum PCEs are provided. | |
DPP-sensitizers for p-type solid-state DSSC have also been reported by Odobel's group in a study published in 2017. Two DPP derivatives with carboxylic acid as the anchoring group were presented. One of them (D30, Fig. 19 and Table 6) contains pyromellitimide (PYRO) as the acceptor substituent. This compound plays the role of a secondary inner electron acceptor to inject exited electrons into the known electron-transporting material PC60BM more efficiently by promoting the fast formation of a DPP+/PCBM− charge-separated state. A Jsc value of up to 0.45 mA cm−2 was achieved with the previously mentioned D23, which is 10 times larger than previously reported values for this kind of device.157,158
![image file: d1tc01872h-f19.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f19.gif) |
| Fig. 19 Chemical structure of D30 for p-type solid-state DSSCs. Adapted from Pham et al.157 | |
In summary, with regard to DPP-based sensitizers, there is still a long path to walk in view of the state of the art, although these systems clearly have a potential that is yet to be exploited. It is likely that their tendency to aggregate limits their utility in DSSCs, and recombination phenomena may occur with high probability.
In light of the state of the art, n-type devices are superior to their p-type counterparts in this series. The highest PCE for an n-type device is currently 10.1% for D3 when the redox pair Co[(bpy)3]3+/2+ was applied as electrolyte and CDCA was the co-adsorbent. As such, given that DPPs are not far from the current record (≈13%), perseverance in design may lead to outstanding performance in the futures.
4. DPP-based single molecules in perovskite solar cells
Perovskite solar cells (PSCs) represent a revolution in the field of photovoltaics. This technology has achieved great attention due to the high efficiencies being achieved, which can even exceed 25%.159,160 Although progress is being made in this regard, long-term stability remains a challenge preventing their entry into the market.161–163 Perovskites are crystalline structures of the ABX3 type in which A is typically an organic cation, such as methylammonium (MA) and/or formamidinium (FA), or an inorganic cation such as cesium or rubidium, B is a metal, generally lead, or, to a lesser extent, tin, and X is a halogen (iodine, bromine or chlorine) (Fig. 20a). The configuration of PSCs can differ depending on the architecture used, and can be mesoporous n–i–p (Fig. 20b), planar n–i–p (Fig. 20c) and planar p–i–n (Fig. 20d). The layers that make up these devices are typically a glass on which the contact is deposited (electron-selective for n–i–p configuration and hole-selective for p–i–n configuration), followed by an electron- or hole-transporting layer (ETL or HTL), then the active or perovskite layer is added (planar or mesoporous). This layer is then covered with another hole- or electron-transporting layer, and finally by a metal contact for the charges to flow. The outermost layer immediately below the metal electrode (ETL or HTL) must let some charges pass and block others (e.g., the ETL must let electrons pass and prevent the passage of holes to minimize recombination phenomena) and should also protect the device against damage, such as by moisture. The single molecule 2,2′,7,-7′-tetrakis(N,N-di-p-methoxyphenylamine)-9,9′-spirobifluorene (spiro-OMeTAD, Fig. 21a) and the polymer poly(triarylamine) (PTAA) are commonly used HTMs to fabricate n–i–p PSCs, and PCBM is a common ETL in p–i–n devices. It is necessary to add doping agents to these materials in small proportions to obtain high performance devices, typically tBP or the salt lithium bis(trifluoromethanesulfonyl)imide (Li-TFSI). However, these dopants are hygroscopic in nature, therefore their presence affects the stability of the PSCs.164–166 As such, it is of interest to develop new HTMs that do not need to be doped to ensure a good performance.
![image file: d1tc01872h-f20.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f20.gif) |
| Fig. 20 (a) Representation of the PSC crystalline structure (e.g., A = FA, MA, Cs, Rb; B = Pb, Sn; X = I, Br, Cl), (b) a mesoporous n–i–p architecture device, (c) a planar n–i–p architecture device, and (d) a planar p–i–n device. | |
![image file: d1tc01872h-f21.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f21.gif) |
| Fig. 21 (a) Chemical structure of spiro-OMeTAD, (b) chemical structures and PCEs for PK1 and PK2, (c) chemical structures and PCEs for PK3 and PKA. Perovskite compositions are included. | |
DPP-based materials can exhibit high charge carrier mobility in conjugated systems, good crystallinity, tend to be robust and have a great chemical versatility. Due to these remarkable properties, they are good candidates for application as HTMs or ETMs in PSCs.167,168
4.1. DPP-based single molecules as hole-transporting materials in PSCs
The use of DPPs in PSCs has not been widely studied to date, although some interesting recent reports can be found. Indeed, studies of DPP-based single molecules as HTMs are the most abundant. The values for the HOMO levels and hole mobilities are crucial parameters since they determine if the HTM will be able to extract holes from the active layer and conduct them to the electrode efficiently. These values, together with the PV parameters for the best devices including DPP-HTMs, are presented in Table 7. In 2016, Jeon et al. published an interesting article describing the study of two bis-N-phenylindolyl-DPP single molecules as dopant-free HTMs in MAPbI3 PSCs with two different N-alkyl chains: one linear (n-octyl, PK1) and another one branched (2-ethylhexyl, PK2) (Fig. 21b). The side chain determines how the molecules arrange in the solid state, thereby affecting the hole extraction ability and charge conductivity of the layer. The linear chain in PK1 causes the molecules to have a strong tendency to aggregate in the film, whereas PK2 films have an amorphous nature, as elucidated by two-dimensional grazing-incidence X-ray diffraction. This means that PK1 exhibits higher molar extinction coefficients at higher wavelengths than PK2, as characterized by UV-vis spectroscopy. Devices made with PK1 performed better than those with PK2 (PCE of 10.14% vs. 5.40%, respectively, measured in a reverse voltage scan). Moreover, an IPCE study showed that PK1 contributes to light harvesting. In addition, time-resolved photoluminescence and transient photovoltage studies showed that the PK1-based device exhibited better charge extraction ability and lower charge recombination than the control dopant-free spiro-MeOTAD-based device.169 The same year, and also using MAPbI3 as active layer, Liu et al. presented a study in which they compared a new DPP-based HTM (PK3) with a new benzodithiophene-based single molecule (PKA) and spiro-OMeTAD in control PSCs (Fig. 21c). The optimized devices fabricated with doped PK3 HTM exhibited a Jsc of 16.60 mA cm−2, a Voc of 0.92 V, an FF of 66% and a PCE of 10.05%, all of which were lower than in the case of the doped PKA (PCE of 12.81%). Both PK3 and PKA demonstrated greater stability than spiro-OMeTAD after aging for 10 days, with a 13% and 14% loss of PCE, respectively, vs. a 36% PCE loss in the case of spiro-OMeTAD.170
Table 7 Perovskite composition, hole mobility, HOMO values and the best PV parameters for PK1–PK10 DPP-based HTMs
HTM |
Perovskite |
μ
h (cm2 V−1 s−1) |
HOMO (eV) |
Dopant |
−Jsc (mA cm−2) |
V
oc (V) |
FF (%) |
PCE (%) |
Ref. |
[Cs0.05(FA0.83MA0.17)0.95]Pb(I0.83Br0.17)3.
|
PK1
|
MAPbI3 |
— |
−4.90 |
No |
15.1 |
0.96 |
70.0 |
10.14 |
169
|
PK2
|
MAPbI3 |
— |
−4.90 |
No |
15.2 |
0.86 |
41.0 |
5.40 |
169
|
PK3
|
MAPbI3 |
— |
−5.13 |
Li-TFSI/tBP |
16.6 |
0.92 |
66.0 |
10.05 |
170
|
PK4
|
MAPbI3 |
— |
−5.20 |
Li-TFSI/tBP |
10.0 |
0.97 |
53.0 |
5.10 |
171
|
PK5
|
MAPbI3 |
— |
−5.21 |
Li-TFSI/tBP |
14.4 |
0.97 |
71.0 |
9.85 |
171
|
PK6
|
MAPbI3 |
— |
−5.22 |
Li-TFSI/tBP |
10.9 |
1.01 |
74.0 |
8.16 |
171
|
PK7
|
MAPbI3 |
1.38 × 10−4 |
−5.15 |
No |
— |
— |
— |
8.63 |
172
|
PK8
|
MAPbI3 |
9.85 × 10−5 |
−5.16 |
No |
— |
— |
— |
8.39 |
172
|
PK9
|
MAPbI3 |
5.32 × 10−4 |
−5.12 |
Li-TFSI |
21.5 |
0.94 |
68.4 |
14.13 |
172
|
|
|
|
|
No |
20.6 |
0.94 |
64.8 |
12.87 |
|
BH34
|
|
— |
−4.90 |
No |
20.6 |
1.10 |
73.8 |
16.80 |
174
|
PK10
|
MAPbI3 |
2.53 × 10−4 |
−4.87 |
No |
14.4 |
0.93 |
60.2 |
8.32 |
175
|
PK11
|
MAPbI3 |
5.89 × 10−4 |
−4.84 |
No |
17.7 |
0.92 |
63.2 |
11.16 |
175
|
PK12
|
MAPbI3 |
6.43 × 10−4 |
−4.89 |
No |
19.8 |
0.94 |
64.0 |
12.05 |
175
|
PK13
|
MAPbI3 |
1.09 × 10−3 |
−4.97 |
No |
22.3 |
1.05 |
71.1 |
17.64 |
|
|
|
1.84 × 10−3 |
|
LiTFSI |
22.9 |
1.14 |
73.9 |
20.19 |
|
Three DPP-based D–π–A–π–D systems were published in 2018 (PK4, PK5 and PK6, Fig. 22a) as part of a study of the effect of two different donor groups (triphenylamine and phenothiazine) and two π-bridges (benzene and thiophene) on PSC performance. PK5 gave the best photovoltaic performance (Jsc = 14.35 mA cm−2, Voc = 0.97 V, FF = 71% and PCE = 9.85%, vs. 5.10% and 8.16% for PK4 and PK6, respectively). The structure of PK5 contains thiophenes as π-bridges and two terminal triphenylamine donor groups. The dihedral angle between the DPP core and the thiophene ring is smaller than that for benzene, which could lead to better organized morphologies and better hole mobilities. The HOMO levels of these three systems are similar, and all of them have adequate LUMO levels to block the flow of electrons. Additionally, a shorter photoluminescence lifetime was observed for PK5 (1.65 ns) by time-resolved photoluminescence than for PK4 and PK6 (9.02 ns and 2.69 ns, respectively), which can be attributed to a better ability to extract holes.171 Three star-shaped systems based on benzo[1,2-b:3,4-b′:5,6-b′′]trithiophene and DPP building blocks were published in 2019 by Kim et al (PK7, PK8 and PK9; Fig. 22b). Differences in PSC performance upon variation of the DPP side chain and extension of the conjugated structure after adding a terminal thiophene ring were studied. Dopant-free PK9, the structure of which comprises a 2-ethylhexyl side chain and an extra terminal thiophene ring, exhibited the best PCE of 12.87%, with corresponding photovoltaic parameters Voc = 0.94 V, Jsc = 20.60 mA cm−2 and FF = 64.8%. This PCE value is higher than those for the other two HTMs PK7 and PK8, which exhibited PCEs of 8.63% and 8.39%, respectively. A marked improvement was obtained when PK9 was doped with Li-TFSI, with a PCE of 14.13%, a Voc of 0.94 V, a Jsc of 21.5 mA cm−2 and an FF of 68.4%. Grazing incidence X-ray diffraction, atomic force microscopy and scanning electron microscopy indicated a nanofibril-type crystallinity for the PK9 film, which seems to result in better charge mobility.172
![image file: d1tc01872h-f22.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f22.gif) |
| Fig. 22 (a) Chemical structures and PCEs for PK4–PK6, (b) chemical structures and PCEs for PK7–PK9, (c) chemical structures for BH36, PKB, PKC and PKD, (d) chemical structures and PCEs for PK10–PK13. Perovskite compositions are included. | |
A further study of interest was published by Molina et al., who reported four ZnPc dimers with 2,5-thienyl (PKB), 2,7-fluorenyl (PKC), 3,6-bisthienyldiketopyrrolopyrrole (BH36)82 and 1,4-phenyl (PKD)173 bridges as dopant-free HTMs in a triple-cation system [Cs0.05(FA0.83MA0.17)0.95]Pb(I0.83Br0.17)3 PSCs (Fig. 22c and Table 7). The push–pull character of BH36 was found to confer a better performance on the PSC compared to the other dopant-free HTM systems studied, with a maximum PCE of 16.8%, a Jsc of 20.6 mA cm−2, a Voc of 1.10 V and an FF of 73.8%, compared to PCEs of 15.5%, 15.6% and 15.7% for PKB, PKC and PKD, respectively, all of them measured under standard global AM 1.5 illumination. Steady-state and time-resolved photoluminescence studies suggested that these dopant-free materials had a comparable hole-extraction capacity to doped spiro-OMeTAD. Shelf and thermal stability tests showed that all ZnPc-based materials studied were more stable than doped spiro-OMeTAD.174
Four HTMs based on DPPs were compared in an interesting study that has been published very recently. The structures include a central DPP with two triphenylamine pendent groups linked to both thiophenes. The structural difference is the alkyl side-chain substituents (2-ethylhexyl-, n-hexyl-, ((methoxyethoxy)ethoxy)ethyl-, and (2-((2-methoxyethoxy)ethoxy)ethyl)acetamide, referred to here as PK10, PK11, PK12 and PK13; Fig. 22d). PK13 gave the best results, exhibiting an efficiency of 17.64% as dopant-free HTM and exceeding 20% when LI-TFSI was added as a dopant (Jsc = 22.94 mA cm−2, Voc = 1.14 V, FF = 73.87%; see Table 7).175
4.2. DPP-based single molecules with other roles in PSCs
Different DPP derivatives have also been investigated in other roles within PSC devices, for example as ETMs, additives and interlayers. Thus, Patil et al. published a study in which the performance of p–i–n planar PSC devices containing PK14 or PCMB, or a mixture of both, as ETL, and with different perovskite compositions, are compared. PK14 (Fig. 23a) has a simple quinoidal structure possessing terminal malononitrile groups. These authors obtained a discrete 3.57% PCE with the double-cation FA0.85MA0.15Pb(I0.8Br0.2)3 perovskite composition when PK14 was the ETL. Although PCBM was better than PK14 in terms of photovoltaic performance (PCE = 8.82%), PK14 offers greater stability than PCBM in OFETs under ambient conditions.176 Huang et al. used the molecule PK15 as a 3D additive in perovskite films (Fig. 23c), adding 0, 0.01 and 0.02 wt% PK15 to the MAPbI3 perovskite solution during manufacture of the devices. Those devices containing 0.01 wt% PK15 in the perovskite layer gave a better performance, with a Jsc of 21.04 mA cm−2, a Voc of 1.02 V, an FF of 65.9% and a PCE of 14.1%, compared to PCEs of 10.6% and 11.6% when 0% and 0.02 wt% of PK15, respectively, was added. X-ray diffraction and scanning electron microscopy studies showed that PK15 acts as a crystallinity improver and grain-boundary filler, UV-vis spectroscopy studies showed that it acts as a light-capturer, and cyclic voltammetry, steady-state and time resolved photoluminescence analysis showed that it also acts as additional electron-donor.177 Zhang et al. were the first to use a p-type organic semiconductor (BH12, Fig. 23b) as the interlayer at a perovskite/HTL interface in n–i–p PSCs, thereby improving the efficiency and stability. BH12 is based on benzo[1,2-b:4,5-b′]dithiophene flanked with two diketopyrrolopyrrole units. PSCs with a BH12 interlayer showed better performances, with a Jsc of 22.0 mA cm−2, a Voc of 1.06 V, an FF of 77.9% and a PCE of 18.2%, compared to a PCE of 16.9% for the control devices. High hole mobility and an appropriate energy level alignment to MAPbI3(Cl) were found. The numerous sulfur atoms can act as Lewis bases, passivating the perovskite layer surface by forming Lewis adducts between infra-coordinated Pb and S, as confirmed by Fourier-transform infrared and Raman spectroscopy; the energy profile was confirmed by performing trap density-of-states measurements. Devices with a BH12 interlayer exhibited greater stability under ambient conditions during 7 days than control devices due to the hydrophobic nature of BH12, which protects the perovskite layer from moisture.178 Derivatives PK15, PK16, PK17 and PK18 were also used as an interlayer between the perovskite layer and the ETL C60 in planar p–i–n PSCs with an MAPbI3 perovskite composition (Fig. 23c). The chemical structures are tetraphenylethylene-diketopyrrolopyrrole with different branched N-alkyl chain lengths. The authors demonstrated that the length of the N-alkyl chain leads to different surface morphologies in the solid state, thus meaning that the ability to extract electrons is affected. All the devices with a DPP-interlayer exhibited a better performance than those with no interlayer, especially those containing PK16, which exhibited a maximum PCE of 18.93%, a Voc of 1.06 V, a Jsc of 22.47 mA cm−2 and a high FF of 80%. The maximum PCEs for the devices using PK15, PK17 and PK18 interlayers were 18.44%, 17.35%, and 17.44%, respectively.179,180
![image file: d1tc01872h-f23.tif](/image/article/2021/TC/d1tc01872h/d1tc01872h-f23.gif) |
| Fig. 23 Chemical structures and PCEs for PK14–PK18. Perovskite compositions are included. | |
In summary, considering the state of the art (PCE > 25%), there is still significant scope for improvement in DPP-based HTM designs. Moreover, features such as hydrophobicity, synthetic versatility, and robustness, along with existing industrial DPP-pigment development, should encourage researchers to find cheap-to-produce DPP-based molecules for PSC applications.
5. Outlook and conclusions
In this article we have reviewed the most relevant studies in the field of photovoltaics involving DPP-based single molecules from the last few years. We have provided a perspective based on the chemical structure in an attempt to find clues about its relationship to performance. DPP-based single molecules stand out as donors in BHJ OSCs, with the highest efficiencies for single-molecule-based devices of more than 12%. The push–pull character of the molecules, in which the acceptor character of the DPP-core and the donor character of other units act together, is decisive for the effective self-ordering of the molecules in the solid state, especially with the appropriate annealing and doping treatments. The molecular design strategies that stand out to date are extension of the conjugation using ethynyl connectors between the different units that make up the molecule, as well as the inclusion of porphyrinoids in the molecular structure in the case of donor systems. DPP-based single molecules are also promising acceptors in OCSs since their chemical versatility allows the energy levels of the acceptor materials to be tuned and to compete with the FA. In general, although star-shaped NFA designs lead to a better performance for OPV devices, a linear donor molecule with a DPP core currently holds the record of 10.05% PCE. Varying results have been obtained for DSSCs to date, probably due to the tendency of DPP derivatives to aggregate, which increases the probability of charge recombination. As such, it is necessary to design structures in which there is a compromise between the tendency to aggregate and adequate charge conduction. As for as the most popular experimental photovoltaic technology to date, namely perovskite solar cells, is concerned, DPP single molecules cannot currently compete with reference materials (e.g. spiro-OMeTAD and PTAA) in terms of efficiency, although they are similar in terms of stability. In addition, it must be considered that the number of publications in each field is currently very different. Even so, a promising maximum PCE of more than 20% has been obtained with the HTM PK13. Furthermore, when included in other roles, for example as ETLs, interlayers or perovskite additives, some benefit has generally been obtained, mainly an improvement in PV parameters and/or stability. These push–pull systems may prove to be fundamental for the development of materials with the characteristics needed for indoor and outdoor PV applications.
Conflicts of interest
There are no conflicts to declare.
Acknowledgements
ASS thanks the Spanish Ministerio de Ciencia e Innovación (MICINN/FEDER) for financial support (CTQ2017-87102-R). MJAM thanks “Beca Santiago Grisolia Grisoliap20177153” de la Comunidad Valenciana.
References
- A. Mahmood, J.-Y. Hu, B. Xiao, A. Tang, X. Wang and E. Zhou, J. Mater. Chem. A, 2018, 6, 16769 RSC
.
- Ö. Birel, S. Nadeem and H. Duman, J. Fluoresc., 2017, 27, 1075 CrossRef PubMed
.
- M. Urbani, M.-E. Ragoussi, M. K. Nazeeruddin and T. Torres, Coord. Chem. Rev., 2019, 381, 1 CrossRef CAS
.
- Y. Duan, X. Xu, Y. Li and Q. Peng, Chin. Chem. Lett., 2017, 28, 2105 CrossRef CAS
.
- F. Fernández-Lázaro, N. Zink-Lorre and Á. Sastre-Santos, J. Mater. Chem. A, 2016, 4, 9336 RSC
.
- A. Tang, C. Zhan, J. Yao and E. Zhou, Adv. Mater., 2017, 29, 1600013 CrossRef PubMed
.
- M. Kaur and D. H. Cho, Chem. Soc. Rev., 2015, 44, 58 RSC
.
- Q. Liu, S. E. Bottle and P. Sonar, Adv. Mater., 2019, 1903882 Search PubMed
.
- W. Li, K. H. Hendriks, M. M. Wienk and R. A. J. Janssen, Acc. Chem. Res., 2016, 49, 78 CrossRef CAS PubMed
.
- Y. Patil and R. Misra, Chem. – Asian J., 2018, 13, 220 CrossRef CAS PubMed
.
- D. G. Farnum, G. Mehta, G. G. I. Moore and F. P. Siegal, Tetrahedron Lett., 1974, 15, 2549 CrossRef
.
- Z. Hao and A. Iqbal, Chem. Soc. Rev., 1997, 26, 203 RSC
.
- S. Ghosh, S. Shankar, D. S. Philips and A. Ajayaghosh, Mater. Today Chem., 2020, 16, 100242 CrossRef CAS
.
-
A. Iqbal and L. Cassar, EP 98808, 1984; Chem. Abstr., 1984, 100, 176461 Search PubMed
.
- S. Loser, S. J. Lou, B. M. Savoie, C. J. Bruns, A. Timalsina, M. J. Leonardi, J. N. Smith, T. Harschneck, R. Turrisi, N. Zhou, C. L. Stern, A. A. Sarjeant, A. Facchetti, R. P. H. Chang, S. I. Stupp, M. A. Ratner, L. X. Chen and T. J. Marks, J. Mater. Chem. A, 2017, 5, 9217 RSC
.
- Y. Patil and R. Misra, J. Mater. Chem. C, 2019, 7, 13020 RSC
.
- M. Grzybowski and D. T. Gryko, Adv. Opt. Mater., 2015, 3, 280–320 CrossRef CAS
.
- S. Qu and H. Tian, Chem. Commun., 2012, 48, 3039 RSC
.
- G. Zhang, Y. Fu, Z. Xie and Q. Zhang, Sol. Energy Mater. Sol. Cells, 2011, 85, 1168 CrossRef
.
- T. K. An, I. Kang, H.-J. Yun, H. Cha, J. Hwang, S. Park, J. Kim, Y. J. Kim, D. S. Chung, S.-K. Kwon, Y.-H. Kim and C. E. Park, Adv. Mater., 2013, 25, 7003 CrossRef CAS PubMed
.
- G.-S. Ryu, K. H. Park, W.-T. Park, Y.-H. Kim and Y.-Y. Noh, Org. Electron., 2015, 23, 76 CrossRef CAS
.
- Y. Li, P. Sonar, L. Murphya and W. Hong, Energy Environ. Sci., 2013, 6, 1684 RSC
.
- Y. Tan, L. Chen, F. Wu, B. Huang, Z. Liao, Z. Yu, L. Hu, Y. Zhou and Y. Chen, Macromolecules, 2018, 51, 8197 CrossRef CAS
.
- J. Huang, C. Zhan, X. Zhang, Y. Zhao, Z. Lu, H. Jia, B. Jiang, J. Ye, S. Zhang, A. Tang, Y. Liu, Q. Pei and J. Yao, Appl. Mater. Interfaces, 2013, 5, 2033 CrossRef CAS PubMed
.
- P. Sonar, T. R. B. Foonga and A. Dodabalapur, Phys. Chem. Chem. Phys., 2014, 16, 4275 RSC
.
- Z. Jiang, Z. Ni, H. Wang, Z. Wang, J. Zhang, G. Qiu, J. Fang, Y. Zhang, H. Dong, K. Lu, W. Hu and Z. Wei, Polym. Chem., 2017, 8, 5603 RSC
.
- B. Lim, H. Sun, J. Lee and Y.-Y. Noh, Sci. Rep., 2017, 7, 164 CrossRef PubMed
.
- Y. Qu, Y. Wu, Y. Gao, S. Qu, L. Yang and J. Hua, Sens. Actuators, B, 2014, 197, 13 CrossRef CAS
.
- S. G. Suryaa, S. S. Nagarkar, S. K. Ghoshc, P. Sonar and V. R. Rao, Sens. Actuators, B, 2016, 223, 114 CrossRef
.
- S. Zhang, T. Sun, D. Xiao, F. Yuan, T. Li, E. Wang, H. Liu and Q. Niu, Spectrochim. Acta, Part A, 2018, 189, 594 CrossRef CAS PubMed
.
- L. Wang, L. Yang, L. Huang and D. Cao, Sens. Actuators, B, 2015, 209, 536 CrossRef CAS
.
- M. Kaur and D. H. Choi, Sens. Actuators, B, 2014, 190, 542 CrossRef CAS
.
- M. R. Kaur, D. S. Yang, K. Choi, M. J. Cho and D. H. Choi, Dyes Pigm., 2014, 100, 118 CrossRef CAS
.
- X. Yang, X. Liu, Y. Li, F. Wu, J. Mao, Y. Yuan, Y. Cui, G. Sun and G. Zhang, Biosens. Bioelectron., 2016, 80, 288 CrossRef CAS PubMed
.
- T. Mukhopadhyay, A. J. Musser, B. Puttaraju, J. Dhar, R. H. Friend and S. Patil, J. Phys. Chem. Lett., 2017, 8, 984 CrossRef CAS PubMed
.
- I. Papadopoulos, M. J. Álvaro-Martins, D. Molina, P. M. McCosker, P. A. Keller, T. Clark, Á. Sastre-Santos and D. M. Guldi, Adv. Energy Mater., 2020, 2001496 CrossRef CAS
.
- C. B. Nielsen, M. Turbiez and L. McCulloch, Adv. Mater., 2013, 25, 1859 CrossRef CAS PubMed
.
- S. D. Collins, N. A. Ran, M. C. Heiber and T.-Q. Nguyen, Adv. Energy Mater., 2017, 7, 1602242 CrossRef
.
- Z. Wang, L. Zhu, Z. Shuai and Z. Wei, Macromol. Rapid Commun., 2017, 38, 1700470 CrossRef PubMed
.
- P. Cheng, G. Li, X. Zhan and Y. Yang, Nat. Photonic., 2018, 12, 131–142 CrossRef CAS
.
- B. C. Thompson and J. M. J. Fréchet, Angew. Chem., Int. Ed., 2008, 47, 58–77 CrossRef CAS PubMed
.
- A. Facchetti, Mater. Today, 2013, 16, 123–132 CrossRef CAS
.
- A. C. Mayer, S. R. Scully, B. E. Hardin, M. W. Rowell and M. D. McGehee, Mater. Today, 2007, 10, 28–33 CrossRef CAS
.
- M. K. Siddiki, J. Li, D. Galipeau and Q. Qiao, Energy Environ. Sci., 2010, 3, 867–883 RSC
.
- S. Rafiquea, S. M. Abdullaha, K. Sulaimana and M. Iwamotob, Renewable Sustainable Energy Rev., 2018, 84, 43–53 CrossRef
.
- C. Yan, S. Barlow, Z. Wang, H. Yan, A. K.-Y. Jen, S. R. Marder and X. Zhan, Nat. Rev. Mater, 2018, 3, 18003 CrossRef CAS
.
- G. Li, D. Li, R. Ma, T. Liu, Z. Luo, G. I. Cui, L. Tong, M. Zhang, Z. Wang, F. Liu, L. Xu, H. Yan and B. Tang, J. Mater. Chem. A, 2020, 8, 5927–5935 RSC
.
-
https://www.nrel.gov/pv/cell-efficiency.html accessed 2021/05/24.
- M. Green, E. Dunlop, J. Hohl-Ebinger, M. Yoshita, N. Kopidakis and X. Hao, Prog. Photovolt. Res. Appl., 2021, 29, 3–15 CrossRef
.
- C. W. Tang, Appl. Phys. Lett., 1986, 48, 2 Search PubMed
.
- D. Kekuda, J.-S. Huang, M. Velusamy, J. T. Lin and C.-W. Chu, Sol. Energy Mater. Sol. Cells, 2010, 94, 1767–1771 CrossRef CAS
.
- C. W. Tang, Appl. Phys. Lett., 1986, 48, 183 CrossRef CAS
.
- W. Kylberg, P. Sonar, J. Heier, J.-N. Tisserant, C. Muller, F. Nuesch, Z.-K. Chen, A. Dodabalapur, S. Yoon and R. Hany, Energy Environ. Sci., 2011, 4, 3617 RSC
.
- P. Sonar, G.-M. Ng, T. T. Lin, A. Dodabalapur and Z.-K. Chen, J. Mater. Chem., 2010, 20, 3626–3636 RSC
.
- Y. Peng, L. Zhang and T. L. Andrew, Appl. Phys. Lett., 2014, 105, 083304 CrossRef
.
- J. S. Zambounis, Z. Hao and A. Iqbal, Nature, 1997, 388, 131–132 CrossRef CAS
.
- M. Rooney, F. Carulli, S. Luzzati, R. Resel, B. Schrode, R. Ruffo, M. Sassi and L. Beverina, Org. Photonics Photovolt, 2018, 6, 8–16 Search PubMed
.
- H. Meier, Angew. Chem., Int. Ed., 2005, 44, 2482–2506 CrossRef CAS PubMed
.
- Y. Patil, R. Misra, F. C. Chen, M. L. Keshtov and G. D. Sharma, RSC Adv., 2016, 6, 99685–99694 RSC
.
- Y. Patil, R. Misra, F. C. Chen and G. D. Sharma, Phys. Chem. Chem. Phys., 2016, 18, 22999–23005 RSC
.
- Y. Patil, R. Misra, M. K. Singh and G. D. Sharma, Phys. Chem. Chem. Phys., 2017, 19, 7262–7269 RSC
.
- H.-J. Yun, H. H. Choi, S.-K. Kwon, Y.-H. Kim and K. Cho, Chem. Mater., 2014, 26, 3928–3937 CrossRef CAS
.
- H. Shi, W. Fu, M. Shi, J. Ling and H. Chen, J. Mater. Chem. A, 2015, 3, 1902 RSC
.
- J. W. Jung, T. P. Russell and W. H. Jo, Chem. Mater., 2015, 27, 4865–4870 CrossRef CAS
.
- Z. Tang, B. Liu, A. Melianas, J. Bergqvist, W. Tress, Q. Bao, D. Qian, O. Inganäs and F. Zhang, Adv. Mater., 2015, 27, 1900–1907 CrossRef CAS PubMed
.
- G. Feng, Y. Xu, J. Zhang, Z. Wang, Y. Zhou, Y. Li, Z. Wei and C. L. W. Li, J. Mater. Chem. A, 2016, 4, 6056–6063 RSC
.
- Y. Patil, R. Misra, A. Sharma and G. D. Sharma, Phys. Chem. Chem. Phys., 2016, 18, 16950–16957 RSC
.
- Y. Lin, J. Wang, T. Li, Y. Wu, C. Wang, L. Han, Y. Yao, W. Ma and X. Zhan, J. Mater. Chem. A, 2016, 4, 1486–1494 RSC
.
- Y. Huo, J. Zhu, X.-Z. Wang, C. Yan, Y.-F. Chai, Z.-Z. Chen, X. Zhan and H.-L. Zhang, J. Mater. Chem. C, 2018, 6, 5843–5848 RSC
.
- W. Leea, J. Choib and J. W. Jung, Dyes Pigm., 2019, 161, 283–287 CrossRef
.
- A. L. Kanibolotsky, I. F. Perepichka and P. J. Skabara, Chem. Soc. Rev., 2010, 39, 2695–2728 RSC
.
- S.-Y. Shiau, C.-H. Chang, W.-J. Chen, H.-J. Wang, R.-J. Jeng and R.-H. Lee, Dyes Pigm., 2015, 115, 35–49 CrossRef CAS
.
- S.-Y. Liu, J. W. Jung, C.-Z. Li, J. Huang, J. Zhang, H. Chen and A. K.-Y. Jen, J. Mater. Chem. A, 2015, 3, 22162–22169 RSC
.
- J. Min-Park, J. H. Lee and W. D. Jang, Coord. Chem. Rev., 2020, 407, 213157 CrossRef
.
- H. M. Qin, L. S. Li, F. Q. Guo, S. J. Su, J. B. Peng, Y. Cao and X. B. Peng, Energy Environ. Sci., 2014, 7, 1397–1401 RSC
.
- T. Liang, L. Xiao, C. Liu, K. Gao, H. Qin, Y. Cao and X. Peng, Org. Electron., 2016, 29, 127–134 CrossRef CAS
.
- L. Bucher, N. Desbois, E. L. N. Koukaras, C. H. Devillers, S. Biswas, G. D. Sharma and C. P. Gros, J. Mater. Chem. A, 2018, 6, 8449–8461 RSC
.
- W. T. Hadmojo, D. Yim, S. Sinaga, W. Lee, D. Y. Ryu, W.-D. Jang, I. H. Jung and S.-Y. Jang, ACS Sustainable Chem. Eng., 2018, 6, 5306–5313 CrossRef CAS
.
- K. Gao, J. Miao, L. Xiao, W. Deng, Y. Kan, T. Liang, C. Wang, F. Huang, J. Peng, Y. Cao, F. Liu, T. P. Russell, H. Wu and X. Peng, Adv. Mater., 2016, 28, 4727–4733 CrossRef CAS PubMed
.
- X. Shi, J. Chen, K. Gao, L. Zuo, Z. Yao, F. Liu, J. Tang and A. K.-Y. Jen, Adv. Energy Mater., 2018, 8, 1702831 CrossRef
.
- K. Gao, S. B. Jo, X. Shi, L. Nian, M. Zhang, Y. Kan, F. Lin, B. Kan, B. Xu, Q. Rong, L. Shui, F. Liu, X. Peng, G. Zhou, Y. Cao and A. K.-Y. Jen, Adv. Mater., 2019, 31, 1807842 CrossRef PubMed
.
- V. Cuesta, M. Vartanian, P. Malhotra, S. Biswas, P. D. L. Cruz, G. D. Sharma and F. Langa, J. Mater. Chem. A, 2019, 7, 11886–11894 RSC
.
- H.-H. Gao, Y. Sun, S. Li, X. Ke, Y. Cai, X. Wan, H. Zhang, C. Li and Y. Chen, Dyes Pigm., 2020, 176, 108250 CrossRef CAS
.
- X. Gao, Y. Wu, X. Song, X. Tao, Y. He, T. Yang, R. Yu, Z. Li and Y. Tao, Dyes Pigm., 2021, 188, 109216 CrossRef CAS
.
- D. Molina, A. Guerrero, G. Garcia-Belmonte, F. Fernández-Lázaro and A. Sastre-Santos, Eur. J. Org. Chem., 2014, 4585 CrossRef CAS
.
- P. Sonar, G.-M. Ng, T. T. Lin, A. Dodabalapur and Z.-K. Chen, J. Mater. Chem., 2010, 20, 3626–3636 RSC
.
- B. P. Karsten, J. C. Bijleveld and R. A. Janssen, Rapid Commun., 2010, 31, 1554–1559 CrossRef CAS PubMed
.
- Y. Patil, R. Misra, M. L. Keshtov and G. D. Sharma, J. Phys. Chem. C, 2016, 120, 6324–6335 CrossRef CAS
.
- Y. Patil, T. Jadhav, B. Dhokale and R. Misra, Asian J. Org. Chem., 2016, 5, 1008–1010 CrossRef CAS
.
- Y. Patil, R. Misraa, M. L. Keshtov and G. D. Sharma, J. Mater. Chem. A, 2017, 5, 3311–3319 RSC
.
- Y. Patila, R. Misraa, R. Singhalb and G. D. Sharma, J. Mater. Chem. A, 2017, 5, 13625–13633 RSC
.
- P. Josse, C. Dalinot, Y. Jiang, S. D. Seignon, J. Roncali, P. Blanchard and C. Cabanetos, J. Mater. Chem. A, 2016, 4, 250–256 RSC
.
- P. Josse, A. Labrunie, C. Dalinot, S. M. McAfee, S. D. Seignon, J. Roncali, G. C. Welch, P. Blanchard and C. Cabanetos, Org. Electron., 2016, 37, 479–484 CrossRef CAS
.
- Y. Eom, C. E. Song, W. S. Shin, S. K. Lee and E. Lim, J. Ind. Eng. Chem., 2017, 45, 338–348 CrossRef CAS
.
- M. Privado, V. Cuesta, P. D. L. Cruz, M. L. Keshtov, R. Singhal, G. D. Sharma and F. Langa, ACS Appl. Mater. Interfaces, 2017, 9, 11739–11748 CrossRef CAS PubMed
.
- Y. Eom, C. E. Song, W. S. Shin, S. K. Lee and E. Lim, J. Ind. Eng. Chem., 2017, 45, 338–348 CrossRef CAS
.
- M. Privado, V. Cuesta, P. D. L. Cruz, M. L. Keshtov, G. D. Sharma and F. Langa, J. Mater. Chem. A, 2017, 5, 14259–14269 RSC
.
- M. Privado, P. D. L. Cruz, S. Biswas, R. Singhal, G. D. Sharma and F. Langa, J. Mater. Chem. A, 2018, 6, 11714–11724 RSC
.
- S. M. McAfee, S. V. Dayneko, P. Josse, P. Blanchard, C. Cabanetos and G. C. Welch, Chem. Mater., 2017, 29, 1309–1314 CrossRef CAS
.
- S. M. McAfee, A.-J. Payne, S. V. Dayneko, G. P. Kini, C. E. Song, J.-C. Lee and G. C. Welch, J. Mater. Chem. A, 2017, 5, 16907–16913 RSC
.
- M. Privado, P. Malhotra, P. de la Cruz, R. Singhal, J. Cerdá, J. Aragó, E. Ortí, G. D. Sharma and F. Langa, Sol. RRL, 2020, 4, 1900471 CrossRef CAS
.
- S. Li, J. Yan, C.-Z. Li, F. Liu, M. Shi, H. Chen and T. P. Russell, J. Mater. Chem. A, 2016, 4, 3777–3783 RSC
.
- A. M. Raynor, A. Gupta, H. Patil, D. Ma, A. Bilic, T. Rooka and S. V. Bhosale, RSC Adv., 2016, 6, 28103–28109 RSC
.
- J. W. Jung and W. H. Jo, Chem. Mater., 2015, 27, 6038–6043 CrossRef CAS
.
- Y.-Q. Pan and G.-Y. Sun, ChemSusChem, 2019, 12, 4570 CrossRef CAS
.
- X. Huang, M. Hu, X. Zhao, C. Li, Z. Yuan, X. Liu, C. Cai, Y. Zhang, Y. Hu and Y. Chen, Org. Lett., 2019, 21, 3382 CrossRef CAS
.
- H. Hang, X. Wu, Q. Xu, Y. Chen, H. Li, W. Wang, H. Tong and L. Wang, Dyes Pigm., 2019, 160, 243 CrossRef CAS
.
- Y. N. Luponosov, A. N. Solodukhin, A. L. Mannanov, P. S. Savchenko, Y. Minenkov, D. Y. Paraschuk and S. A. Ponomarenko, Dyes Pigm., 2020, 177, 108260 CrossRef CAS
.
- K. Wang, P. Xia, K. Wang, X. You, M. Wu, H. Huang, D. Wu and J. Xia, ACS Appl. Mater. Interfaces, 2020, 12, 9528 CrossRef CAS PubMed
.
- A. Stanculescua, C. Breazua, M. Socol, O. Rasoga, N. Preda, G. Petre, A. M. Solonaru, M. Grigoras, F. Stanculescu, G. Socol, G. Popescu-Pelin and M. Girtan, Appl. Surf. Sci., 2020, 509, 145351 CrossRef
.
- J. Hu, X. Liu, K. Wang, M. Wu, H. Huang, D. Wu and J. Xia, J. Mater. Chem. C, 2020, 8, 2135 RSC
.
- B. A. Gregg, J. Phys. Chem. Lett., 2011, 2, 3013 CrossRef CAS
.
- C. Zhan, X. Zhang and J. Yao, RSC Adv., 2015, 5, 93002 RSC
.
- A. Gupta, A. Rananaware, P. S. Rao, D. D. La, A. Bilic, W. Xiang, J. Li, R. A. Evans, S. V. Bhosalec and S. V. Bhosale, Mater. Chem. Front., 2017, 1, 1600–1606 RSC
.
- A. Rananaware, A. Gupta, J. L. Li, A. Bilic, L. Jones, S. Bhargavad and S. V. Bhosale, Chem. Commun., 2016, 52, 8522–8525 RSC
.
- S.-Y. Liu, W.-Q. Liu, C.-X. Yuan, A.-G. Zhong, D. Han, B. Wang, M. N. Shah, M.-M. Shi and H. Chen, Dyes Pigm., 2016, 134, 139–147 CrossRef CAS
.
- P. Sun, H. Sun, X. Li, Y. Wang, H. Shan, J. Xu, C. Zhang, Z. Xu, Z.-K. Chen and W. Huang, Dyes Pigm., 2017, 139, 412–419 CrossRef CAS
.
- H. Yuhui, W. Wenlin, Y. Liyang, L. Kaijun, X. Xiaopeng, L. Ying and P. Qiang, Acta Chim. Sin., 2020, 78, 1246 CrossRef
.
- R. W. Jadhav, R. W. Hangarge, M. D. Aljabri, K. S. More, J.-Y. Chen, L. A. Jones, R. A. Evans, J.-L. Li, S. V. Bhosale and A. Gupta, Mater. Chem. Front., 2020, 4, 2176 RSC
.
- M. J. Álvaro-Martins, J. G. Sánchez, G. Lavarda, D. Molina, J. Pallarès, T. Torres, L. F. Marsal and Á. Sastre-Santos, ChemPlusChem, 2021, 86 DOI:10.1002/cplu.202100103
.
- X.-F. Wu, W.-F. Fu, Z. Xu, M. Shi, F. Liu, H.-Z. Chen, J.-H. Wan and T. P. Russell, Adv. Funct. Mater., 2015, 25, 5954–5966 CrossRef CAS
.
- S. Li, W. Liu, M. Shi, J. Mai, T.-K. Lau, J. Wan, X. Lu, C.-Z. Li and H. Chen, Energy Environ. Sci., 2016, 9, 604–610 RSC
.
- W. Liu, S. Li, J. Huang, S. Yang, J. Chen, L. Zuo, M. Shi, X. Zhan, C.-Z. Li and H. Chen, Adv. Mater., 2016, 28, 9729–9734 CrossRef CAS PubMed
.
- Z.-C. Chen, Y. Xie, Y.-Y. Yu, H.-B. Wu and J.-H. Wan, New J. Chem., 2018, 42, 11854–11861 RSC
.
- P. Sun, X. Li, Y. Wang, H. Shan, J. Xu, C. Liu, C. Zhang, F. Chen, Z. Xu, Z.-K. Chen and W. Huang, RSC Adv., 2018, 8, 25031–25039 RSC
.
- B. O’Regan and M. Grätzel, Nature, 1991, 353, 737 CrossRef
.
- E. Benazzi, J. Mallows, G. H. Summers, F. A. Blacka and E. A. Gibson, J. Mater. Chem. C, 2019, 7, 10409 RSC
.
- R. Cisneros, M. Beley and F. Lapicque, Phys. Chem. Chem. Phys., 2016, 00, 1 Search PubMed
.
- H.-W. Bahng, A. Hagfeldt and J.-E. Moser, J. Phys. Chem. C, 2018, 122, 19348 CrossRef CAS
.
- H.-W. Bahng, A. Hagfeldt and J.-E. Moser, J. Phys. Chem. C, 2018, 122, 19359 CrossRef CAS
.
- S. Mathew, A. Yella, P. Gao, R. Humphry-Baker, B. F. Curchod, N. Ashari-Astani, I. Tavernelli, U. Rothlisberger, M. K. Nazeeruddin and M. Gratzel, Nat. Chem., 2014, 6, 242 CrossRef CAS PubMed
.
- Y. Lu, Y. Cheng, C. Li, J. Luo, W. Tang, S. Zhao, Q. Liu and Y. Xie, Sci. China: Chem., 2019, 62, 994 CrossRef CAS
.
- D. Zhang, M. Stojanovic, Y. Ren, Y. Cao, F. T. Eickemeyer, E. Socie, N. Vlachopoulos, J.-E. Moser, S. M. Zakeeruddin, A. Hagfeldt and M. Grätzel, Nat. Commun., 2021, 12, 1777 CrossRef CAS PubMed
.
-
K. Kunimoto, H. Yamamoto, S. Nakamichi, R. Takahashi and J. Tanabe, PCT Int. Appl. ( 2009), WO 2009109499 A1 20090911 Search PubMed
.
- F.-L. Guo, S.-Y. Qu, W.-J. Wu, J. Li, W.-J. Ying and J.-L. Hua, Synth. Met., 2010, 160, 1767 CrossRef CAS
.
- S. Qu, W. Wu, J. Hua, C. Kong, Y. Long and H. Tian, J. Phys. Chem., 2010, 114, 1343 CAS
.
- F. Guo, X. Liu, Y. Ding, F. Kong, W. Chen, L. Zhoua and S. Dai, RSC Adv., 2016, 6, 13433 RSC
.
- J. Zhang, N. Vlachopoulos, Y. Hao, T. W. Holcombe, G. Boschloo, E. M. J. Johansson, M. Grätzel and A. Hagfeldt, Chem. Phys. Chem., 2016, 17, 1441 CrossRef CAS PubMed
.
- Z. Liu, K. Duan, H. Guo, Y. Deng, H. Huang, X. Yi, H. Chen and S. Tan, Dyes Pigm., 2017, 140, 312 CrossRef CAS
.
- A. E. Yemene, V. Venkatraman, D. M. Almenningen, B. H. Hoff and O. R. Gautun, Molecules, 2020, 25, 2349 CrossRef CAS PubMed
.
- J.-H. Yum, T. W. Holcombe, Y. Kim, K. Rakstys, T. Moehl, J. Teuscher, J. H. Delcamp, M. K. Nazeeruddin and M. Grätzel, Sci. Rep., 2013, 3, 2446 CrossRef PubMed
.
- P. Ganesan, A. Yella, T. W. Holcombe, P. Gao, R. Rajalingam, S. A. Al-Muhtaseb, M. Grätzel and M. K. Nazeeruddin, ACS Sustainable Chem. Eng., 2015, 3, 2389 CrossRef CAS
.
- X. Li, Z. Zheng, W. Jiang, W. Wu, Z. Wang and H. Tian, Chem. Commun., 2015, 51, 3590 RSC
.
- K. Y. Chiu, V. Govindan, L.-C. Lin, S.-H. Huang, J.-C. Hu, K.-M. Lee, H.-H. G. Tsai, S.-H. Chang and C.-G. Wu, Dyes Pigm., 2016, 125, 27 CrossRef CAS
.
- Y. Hao, Y. Saygili, J. Cong, A. Eriksson, W. Yang, J. Zhang, E. Polanski, K. Nonomura, S. M. Zakeeruddin, M. Grätzel, A. Hagfeldt and G. Boschloo, ACS Appl. Mater. Interfaces, 2016, 8, 32797 CrossRef CAS PubMed
.
- H. Shimogawa, M. Endo, T. Taniguchi, Y. Nakaike, M. Kawaraya, H. Segawa, Y. Murata and A. Wakamiya, Bull. Chem. Soc. Jpn., 2017, 90, 441 CrossRef CAS
.
- H. Shimogawa, M. Endo, Y. Nakaike, Y. Murata and A. Wakamiya, Chem. Lett., 2017, 46, 715 CrossRef CAS
.
- S. Zhang, X. Yang, C. Qin, Y. Numata and L. Han, J. Mater. Chem. A, 2014, 2, 5167 RSC
.
- G. Boschloo, L. Häggman and A. Hagfeldt, J. Phys. Chem. B, 2006, 110, 13144 CrossRef CAS PubMed
.
- G. Wang, Z. Liu, Y. Deng, L. Xie and S. Tan, Dyes Pigm., 2017, 145, 427 CrossRef CAS
.
- J.-D. Decoppet, S. B. Khan, M. S. A. Al-Ghamdi, B. G. Alhogbi, A. M. Asiri, S. M. Zakeeruddin and M. Grätzel, Energy Technol., 2017, 5, 321 CrossRef CAS
.
- D.-S. Lim, K. Choi, D. Hayati, D.-H. Park, A. Ghifari, K. M. Lee, Y. Ko, Y. Jun, H.-J. Suk and J. Hong, Dyes Pigm., 2020, 173, 107840 CrossRef CAS
.
- I. R. Perera, T. Daeneke, S. Makuta, Z. Yu, Y. Tachibana, A. Mishra, P. Buerle, C. A. Ohlin, U. Bach and L. Spiccia, Angew. Chem., Int. Ed., 2015, 54, 3758 CrossRef CAS PubMed
.
- L. Favereau, J. Warnan, Y. Pellegrin, E. Blart, M. Boujtita, D. Jacquemin and F. Odobel, Chem. Commun., 2013, 49, 8018 RSC
.
- Y. Farré, L. Zhang, Y. Pellegrin, A. Planchat, E. Blart, M. Boujtita, L. Hammarström, D. Jacquemin and F. Odobel, J. Phys. Chem. C, 2016, 120, 7923 CrossRef
.
- Y. Farré, M. Raissi, A. Fihey, Y. Pellegrin, E. Blart, D. Jacquemin and F. Odobel, ChemSusChem, 2017, 10, 2618–2625 CrossRef
.
- T. T. T. Pham, S. K. Saha, D. Provost, Y. Farré, M. Raissi, Y. Pellegrin, E. Blart, S. Vedraine, B. Ratier, D. Aldakov, F. Odobel and J. Bouclé, J. Phys. Chem. C, 2017, 121, 129 CrossRef CAS
.
- L. Zhang, G. Boschloo, L. Hammarströma and H. Tian, Phys. Chem. Chem. Phys., 2016, 18, 5080 RSC
.
-
N. G. Park, M. Grätzel and T. Miyasaka, Organic–inorganic halide perovskite photovoltaics: From fundamentals to device architectures, Springer International Publishing, 2016, pp. 1–366, ISBN 978-3-319-35114-8 Search PubMed
.
-
https://www.nrel.gov/pv/assets/pdfs/best-research-cell-efficiencies.20190802.pdf, accessed 2021/05/24.
- M. I. H. Ansari, A. Qurashi and M. K. Nazeeruddin, J. Photochem. Photobiol., C, 2018, 35, 1 CrossRef CAS
.
- Z. Yang, J. Song, H. Zeng and M. Wang, Mater. Today Energy, 2019, 14, 100338 CrossRef
.
- W.-W. Liu, T.-H. Wu, M.-C. Liu, W.-J. Niu and Y.-L. Chueh, Adv. Mater. Interfaces, 2019, 6, 1801758 CrossRef
.
- J.-Y. Seo, H.-S. Kim, S. Akin, M. Stojanovic, E. Simon, M. Fleischer, A. Hagfeldt, S. M. Zakeeruddin and M. Grätzel, Energy Environ. Sci., 2018, 11, 2985 RSC
.
- J. Luo, C. Jia, Z. Wan, F. Han, B. Zhao and R. Wang, J. Power Sources, 2017, 342, 886 CrossRef CAS
.
- B. Xu, J. Huang, H. Agren, L. Kloo, A. Hagfeldt and L. Sun, ChemSusChem, 2014, 7, 3252 CrossRef CAS PubMed
.
- A. Tang, C. Zhan, J. Yao and E. Zhou, Adv. Mater., 2017, 29, 1600013 CrossRef
.
- Y. Patil and R. Misra, Chem. – Asian J., 2018, 13, 220 CrossRef CAS
.
- S. Jeon, U. K. Thakur, D. Lee, Y. Wenping, D. Kim, S. Lee, T. K. Ahn, H. J. Park and B.-G. Kim, Org. Electron., 2016, 37, 134 CrossRef CAS
.
- X. Liu, F. Kong, Z. Tan, T. Cheng, W. Chen, T. Yu, F. Guo, J. Chen, J. Yao and S. Dai, RSC Adv., 2016, 6, 87454 RSC
.
- H. Cheng, X. Zhao, Y. Shen, M. Wang, L. Wang, H. Meier and D. Cao, J. Energy Chem., 2018, 27, 1175 CrossRef
.
- S. R. Suranagi, R. Singh and M. Kim, Dyes Pigm., 2019, 163, 525 CrossRef CAS
.
- D. Molina, M. A. Ruiz-Preciado, F. Sadegh, M. João Álvaro-Martins, M. Grätzel, A. Hagfeldt and Á. Sastre-Santos, J. Porphyrins Phthalocyanines, 2019, 23, 547 CrossRef
.
- D. Molina, M. A. Ruiz-Preciado, B. Carlsen, F. T. Eickemeyer, B. Yang, M. J. Álvaro-Martins, K. Nonomura, A. Hagfeldt and Á. Sastre-Santos, ChemPhotoChem, 2020, 4, 1 CrossRef
.
- A. Sharma, R. Singh, G. P. Kini, J. H. Kim, M. Parashar, M. Kim, M. Kumar, J. S. Kim and J.-J. Lee, ACS Appl. Mater. Interfaces, 2021, 13, 7405 CrossRef CAS PubMed
.
- S. Sharma, N. Sakai, S. Ray, Sa. P. Senanayak, H. Sirringhaus, H. J. Snaith and S. Patil, Sol. Energy, 2019, 186, 9 CrossRef CAS
.
- B. Huang, Q. Fu, Q. Ai, L. Tan, L. Chen and Y. Chen, Mater. Chem. Front., 2017, 1, 1179 RSC
.
- M. Zhang, J. Wang, L. Li, G. Zheng, K. Liu, M. Qin, H. Zhou and X. Zhan, Adv. Sci., 2017, 4, 1700025 CrossRef PubMed
.
- R. Wang, J. Qiao, B. He, X. Tang, F. Wu and L. Zhu, J. Mater. Chem. C, 2018, 6, 8429 RSC
.
- B. He, R. Wang, H. Lu, Y. Ji, Q. Song, X. Tang, Y. Jin, F. Wu and L. Zhu, Org. Electron., 2019, 69, 13 CrossRef CAS
.
|
This journal is © The Royal Society of Chemistry 2021 |