Hairong
Long‡
ab,
Jie
An‡
b,
Shuxing
Xu
ab,
Xiuhui
Ni
cd,
Erming
Su
ab,
Yingjin
Luo
b,
Shijie
Liu
be and
Tao
Jiang
*abe
aSchool of Chemistry and Chemical Engineering, Guangxi University, Nanning, Guangxi 530004, P. R. China
bCAS Center for Excellence in Nanoscience, Beijing Key Laboratory of Micro-Nano Energy and Sensor, Beijing Institute of Nanoenergy and Nanosystems, Chinese Academy of Sciences, Beijing 101400, P. R. China. E-mail: jiangtao@binn.cas.cn
cShandong Technological Center of Oceanographic Instrumentation Co., Ltd, Qingdao 266001, P. R. China
dInstitute of Oceanographic Instrumentation, QiLu University of Technology (Shandong Academy of Sciences), Qingdao 266001, P. R. China
eSchool of Nanoscience and Technology, University of Chinese Academy of Sciences, Beijing 100049, P. R. China
First published on 5th January 2023
Effective power management on the outputs of triboelectric nanogenerators (TENGs) is critical for their practical applications due to the large impedance and unbalanced load matching. Recently proposed voltage multiplying circuits for external-charge excitation and self-charge excitation are usually unstable and require reversal for device restarting and common switched-capacitor-converters usually cause large switching losses. In this work, we fabricated a fractal structured charge-excitation circuit for TENGs using diodes and capacitors. The fractal switched-capacitor-converter coupled with voltage regulator diodes can greatly boost the output charge and current of the TENG without reverse starting. The managed output performance of the TENG can be controlled by the electronic component parameters and external operating frequency. Through the component and condition optimization, the fractal structured charge-excitation TENG (FSC-TENG) can achieve nearly 5.8 times charge boosting and almost 16.8 times power boosting in the pulsed mode. Furthermore, the FSC-TENG successfully drove a hygrothermograph and was integrated into a yoga mat for harvesting human-body motion energy to power an electronic watch and a pedometer. The FSC-TENG with good charge accumulation properties and stability is a promising candidate for practical self-powered applications.
The triboelectric nanogenerator (TENG) invented by Prof. Wang, based on the coupling effect of triboelectrification and electrostatic induction, can effectively convert randomly-distributed, irregular, and low-frequency mechanical energy into electricity.19 It adopts the mechanism of Maxwell's displacement current and exhibits the merits of low cost,20,21 easy to fabricate,22 diverse material selection,23 and wide application range.24 It can be applied in the fields of wearable devices,25 smart homes,26 and memory of electronic equipment,27etc. In order to enhance the charge density of tribo-surfaces for improving the power output of TENG toward practical applications, considerable efforts have been made through various approaches, such as material modification,2 surface structuring,28 charge pumping,29,30 charge shuttling,31 self-charge excitation,32,33 mechanical switch adjustment,34 and multi-switch operation.35 In 2018, a charge excitation strategy for the TENG system was proposed using a voltage multiplying circuit (VMC) to implement external-charge excitation and self-charge excitation of TENG.33 The output performance of the TENG was significantly boosted by the VMC, but the circuit is unstable and requires reversal for device restarting when releasing the charges from the capacitors. Then, a switched-capacitor-converter based on the fractal design (FSCC) was proposed in 2019, which is equivalent to a fractal structure VMC that can lower the voltage and boost the charge and current.36 However, it is difficult to prepare closed electronic devices due to the requirement of adding automatic switches to control the outputs. Therefore, we urgently need to overcome the above drawbacks, so that the charge excitation circuit can be used in actual situations for powering small portable electronics by the TENG.
In this work, an FSCC (fractal structured VMC) with voltage regulator diodes was developed to manage the electrical outputs of TENG, where the fractal charge-excitation circuit can realize the charge boosting without reverse starting. The influences of the electronic component parameters and external operating frequency on the output charge and current of the fractal structured charge-excitation TENG (FSC-TENG) were systematically investigated. The FSCC integrated on a printed circuit board (PCB) can boost the output charge of a common TENG by nearly 5.8 times under regular triggering, achieving a short-circuit current of 36.5 μA and a transferred charge of 752.4 nC. Then, the FSC-TENG could deliver an output power of 7.83 mW with an enhancement of about 16.8 times, which can easily drive a hygrothermograph. Furthermore, the FSC-TENG was placed underneath a yoga mat to capture human-body motion energy for powering portable electronics such as an electronic watch and a pedometer, demonstrating important application prospects of the FSC-TENG system with good charge accumulation property and stability.
Fig. 1d–i shows the working principle for the FSC-TENG system. At the initial state, there are no charges stored in the four capacitors (Fig. 1d). Here, the TENG acted as a voltage source (voltage V is applied to the FSCC) and the connection manner of capacitors in the FSCC can automatically switch between the series and parallel. When the tribo-pair in the TENG was separated, the electrostatic charges are transferred to the FSCC, as shown in Fig. 1e. Along the red line, the input charge Q flows across the capacitors in series, and each capacitor has a charge Q and the voltage of V/4. When the TENG was into a contact state again, the decrease in voltage V resulted in the charge transfer from the capacitors to the TENG (Fig. 1f). The capacitor connection was automatically switched to be in parallel, due to the unidirectional conductivity of the diodes. The output charge of 4Q–4Q′ and the voltage of V/4–2Vd were released and fed back to the TENG, where Q′ and 2Vd are the charge and total output voltage drop, retained in each capacitor because of the turn-on voltage drop of the diodes, and Vd is the voltage drop of one diode. The equivalent circuit of the discharge process of an N-unit FSCC consists of N capacitors in parallel and m diodes in series, resulting in the total output voltage drop of mVd and residue charge of NC·mVd (Fig. 1g). The output charge released from the FSCC is NQ–NC·mVd, in which, N = 4 for this work. After several cycles, the charges flow back to the TENG until the charge saturation (Fig. 1h), where further charge excitation may induce the air breakdown. To ensure stable output, a regulator diode was used to control the voltage and thus release excessive charges (Fig. 1i).
To verify the functionality of the FSC-TENG system, the output performance of the TENG was systematically tested and compared for the two cases with and without charge excitation (Fig. 2a) under regular triggering of the linear motor. The moving distance of the linear motor was fixed at 14 cm, and the frequency was set to 1 Hz in the tests. When the common TENG was directly connected to the linear motor, the short-circuit current and transferred charge of the TENG were only 3.5 μA and 110.0 nC, respectively (Fig. 2b and c). On the other hand, for the FSC-TENG, with an FSCC consisting of 9 rectifier diodes, 4 ceramic capacitors, and voltage regulator diodes, the short-circuit current and transferred charge of the TENG reach saturation values after 25 s (Fig. 2d and e), which were 36.5 μA and 752.4 nC, respectively. However, it was found that the outputs were unstable without the regulator diodes (ESI Fig. S2a and b†), which is related to the fractal structure of the self-excitation circuit itself. Appropriate regulated voltage was chosen to ensure the output stability of the TENG. The voltage output of the TENG with/without the charge excitation is shown in ESI Fig. S3.† In addition, in order to study whether the FSCC can be re-charged after discharging, we discharged the capacitors and then re-measured the outputs of TENG at 1 Hz, as shown in Fig. 2f and g. It can be seen that the short-circuit current and transferred charge can increase again until they get saturated. ESI Video S1† records the recharging process after the discharging process at a frequency of 1 Hz, and the corresponding transferred charge profile of the FSC-TENG is shown in ESI Fig. S4.† The fractal charge-excitation circuit improves the output performance of the TENG, and the matched regulator diode can maintain and stabilize the maximum outputs to a certain extent, during the charging and discharging process, which again verifies the good stability of this circuit.
Subsequently, the effects of different parameters on the output performance of the FSC-TENG device under regular triggering were investigated, as shown in Fig. 3. ESI Table S1† shows the parameters of the electronic components used in this work. Because a large leakage current will bring great energy loss, especially in high-voltage applications, we tried choosing diodes with a small reverse leakage current. The relationship between the current/charge and withstand voltage of the rectifier diodes is shown in Fig. 3a and ESI Fig. S5a and b,† indicating that the short-circuit current and transferred charge both attain the maximum values at the withstand voltage of 800 V. The maximum short-circuit current and transferred charge arrive at 40.2 μA and 772.5 μC, respectively. Fig. 3b and ESI Fig. S5c and d† show that the short-circuit current and the transferred charge gradually increase when the capacitance of the adopted ceramic capacitors increases. The saturation values of current and charge rise from 16.6 μA and 591.4 nC (for 1 nF capacitor) to 41.7 μA and 778.0 nC (for 100 nF capacitor), respectively. Nevertheless, it takes more time to reach the charging saturation for larger capacitors, so the capacitors used in our FSC-TENG device are 22 nF. Fig. 3c and ESI Fig. S5e and f† present the effect of the regulator diode number on the outputs. As the number of regulator diodes increases from 1 to 4, the short-circuit current and transferred charge both increase, but they both decrease upon further increasing the regulator diode number.
Besides the electronic component parameters, the influence of the external operating frequency on the electrical outputs of the FSC-TENG was investigated. When the frequency increases from 0.5 Hz to 2.0 Hz, the short-circuit current gradually increases, while the transferred charge possesses an optimum value of 752.4 nC at the frequency of 1 Hz, as shown in Fig. 3d and ESI Fig. S6.† The output current is nearly proportional to the frequency, reaching a maximum value of 43.7 μA at a frequency of 2 Hz. After optimizing the electronic component parameters, we also found that there exists a difference when these components are integrated on a breadboard or PCB. As shown in Fig. 3e and ESI Fig. S7,† the saturated current, and charge can increase from 34.0 μA and 633.0 nC (using the breadboard) to 36.5 μA and 752.4 nC (using the PCB), which may be due to the formation of many micro-capacitors by the metal foil on the breadboard. According to the above results, the fractal structure charge-excitation circuit of 4 = 2 × 2, which consists of four Zener diodes of 150 V, nine rectifier diodes of 800 V, and four 22 nF ceramic capacitors, was chosen in the next experiments. Fig. 3f shows the profiles of short-circuit current and transferred charge of the FSC-TENG at the optimum conditions. The operating frequency was chosen as 1 Hz.
The resistive behavior of the FSC-TENG at the frequency of 2.0 Hz was studied and compared with the common TENG. As shown in Fig. 4a and b, when the load resistance increases from 0.1 MΩ to 200 MΩ, the current of the common TENG decreases from 7.6 μA to 0.7 μA, and a maximum power of 0.44 mW can be delivered at the matched resistance of 50 MΩ. In contrast, the current and power of the FSC-TENG arrived at 42.6 μA and 7.83 mW, respectively. The power has an enhancement of 16.8 times, and the matched resistance is still 50 MΩ. Fig. 4c(i) shows the variation process of the transferred charge for the FSC-TENG in 2500 s. Fig. 4c(ii) presents the enlarged view of the ongoing charge accumulation, and Fig. 4c(iii) represents the state of charge saturation. In addition, the charging capabilities of the TENG for different capacitors were compared between the two cases with and without charge excitation. As shown in Fig. 4d and e, the charging voltage of a 10 μF capacitor reaches 2.3 V in 120 s for a common TENG, while the FSC-TENG can charge the capacitor to 15.2 V, with an improvement of 42.7 times in the stored energy. ESI Fig. S8† shows the charging profiles for different capacitors in the unsaturated state, and an enlarged view of the charging profiles during the charge excitation process is also shown. Both states demonstrate that the FSC-TENG can greatly increase the charging speed.
Finally, the practical applications of the FSC-TENG in our daily lives were demonstrated. Using the FSCC to manage the TENG for harvesting mechanical energy that could power some small portable electronic devices, through a mechanical switch and an energy storage capacitor, as shown in Fig. 5a. The FSCC contains nine rectifier diodes with a withstand voltage of 800 V, four regulator diodes of 150 V, four 10 nF ceramic capacitors, and an electrolytic capacitor. First, the FSC-TENG was employed to charge a 220 μF capacitor to drive a hygrothermograph under the regular triggering of a linear motor. When the voltage reaches 2.0 V, the hygrothermograph starts to work, and the temperature and humidity data are presented on the liquid crystal display screen. The charging and discharging processes of the capacitor to power the hygrothermograph is shown in Fig. 5b, and the experimental process is demonstrated in ESI Video S2.†
Nowadays, more and more people love sports, which are good for their physical and mental health. In this context, we tried to integrate our TENG device with a yoga mat to harvest the human-body motion energy. The device uses an acrylic plate with a 5 mm-thick sponge as the substrate, leaving two 100 mm × 100 mm grooves in the substrate, and the two TENGs placed in the grooves are connected to the FSCC. Fig. 5c shows the front views and sectional view of the yoga mat, and the photograph of the yoga mat integrated with the FSC-TENG is shown in ESI Fig. S9.† A capacitor of 100 μF was adopted to store the translated electrical energy for powering an electronic watch, as shown in Fig. 5d. After a person exercises on the yoga mat for 60 s, the voltage rises rapidly to 2.0 V, and the electronic watch starts to work. The watch can continue to work for 70 s after the stopping motion (ESI Video S3†), thus it can help the exerciser know the resting time. Another application demonstration is powering a pedometer by the FSC-TENG. During the exercising process, a 470 μF capacitor is charged to 1.5 V after 360 s, and the switch is turned on so that the pedometer is connected and works properly. Fig. 5e(ii) and (iii) shows the exerciser moves on 28 steps during 18 s. The charging and discharging processes of the capacitor to power the pedometer are shown in Fig. 5e, and the experimental process is demonstrated in ESI Video S4.† If we increase the number of FSC-TENGs to form an array, more output energy can be generated, and the charging time can be shortened.
Footnotes |
† Electronic supplementary information (ESI) available. See DOI: https://doi.org/10.1039/d2nr06328j |
‡ These authors contributed equally to this work. |
This journal is © The Royal Society of Chemistry 2023 |