Progress in organic photovoltaics for indoor application

Organic photovoltaics (OPVs) have recently emerged as feasible alternatives for indoor light harvesting because of their variable optical absorption, high absorption coefficients, and low leakage currents under low lighting circumstances. Extensive research has been performed over the last decade in the quest for highly efficient, ecologically stable, and economically feasible indoor organic photovoltaics (IOPVs). This research covers a wide range of topics, including the development of new donor–acceptor materials, interlayers (such as electron and hole transport layers), energy loss reduction, open-circuit voltage enhancement via material and device engineering, and device architecture optimization. The maximum power conversion efficiency (PCE) of IOPVs has already topped 35% as a consequence of these collaborative efforts. However, further research is needed to improve numerous elements, such as manufacturing costs and device longevity. IOPVs must preserve at least 80% of their initial PCE for more than a decade in order to compete with traditional batteries used in internet of things devices. A thorough examination of this issue is urgently required. We intend to present an overview of recent developments in the evolution of IOPVs.


Introduction
][3][4][5][6][7][8][9][10] In general, these devices are operated by extracting power from normal batteries, but these types of power systems need regular replacement and maintenance, which is very difficult because of the tinny and wireless nature of those devices. 11,12Consequently, harvesting of ambient energy is the most appropriate alternative solution.Most components of IoT networks operate indoors. 13,14Articial lighting sources such as uorescent lamps (FL), compact uorescent lamps (CFL), halogen lamps, light-emitting diodes (LEDs) (both warm and cold white), incandescent lamps, and natural sunlight through windows are the most reliable and accessible resource for collecting energy and charging such devices. 15A photovoltaic (PV) device is the main tool needed for harvesting light energy.When compared to outdoor conditions, the light intensity is noticeably lower in indoor. 16The intensity of light has a signicant impact on a variety of characteristics and performance parameters, including short-circuit current density (J SC ), open-circuit voltage (V OC ), ll factor (FF), and power conversion efficiency (PCE) of a PV device. 17The effect of light intensity on these factors may vary depending on the individual PV technology under consideration.For instance, J SC of a PV device generally increases with light intensity.This is because higher light intensity results in more photons being absorbed by the semiconductor material, leading to a greater number of electron-hole pairs being generated and contributing to a higher current.Whereas, V OC is relatively unaffected by changes in light intensity.However, under very low light conditions, the V OC might show a slight increase due to reduced recombination losses.The FF, denoting the efficiency of converting incident light into electrical power within a solar cell, may enhance with escalating light intensity, owing to diminished recombination losses.Yet, under exceedingly high light intensities, the FF could potentially decline due to the PV device's non-ideal behaviour.Given the interdependence of these parameters on light intensity, the PCE of the device also exhibits reliance on light intensity.Among the several PV devices available, the organic photovoltaic (OPV) device stands out as an excellent alternative for harvesting indoor light.This preference stems mostly from its notable absorption coefficient in the visible spectrum (which corresponds to the irradiance spectra of common interior light sources).Furthermore, its tuneable optical characteristics provide an advantage in circumstances when the indoor illumination spectrum is well dened, potentially leading to increased efficiency.The intrinsic versatility of OPV technology adds to its allure, allowing for creative integration into a variety of surfaces such as tiny electronic devices, windows, walls, and even fabrics.This versatility opens the door to novel design concepts and aesthetic possibilities that would be impossible to realize with rigid solar technology.9][20][21][22][23][24][25][26][27][28][29][30][31][32][33][34][35] On the other hand, when it comes to outdoor use, OPVs have various disadvantages.These include lower efficiency due to their restricted absorption band, which limits their practicality for energy-intensive outdoor scenarios that rely on optimizing energy output.Furthermore, the stability of OPV materials is weakened under outdoor condition that expose them to more demanding factors such as UV radiation, temperature variations, and moisture exposure.This exposure increases the likelihood of rapid deterioration and shorter operating lifespans.
7][38] To achieve this objective, a range of approaches have been put into practice.Among these strategies, producing broad band-gap organic semiconductors with extraordinarily high absorption coefficients has received special attention.This focus is due to the fact that the emission spectra of many indoor light sources are mostly in the visible spectrum (400-700 nm).As a result, the optical bandgap of the semiconductors used in IOPV must lie within the energy range of 1.8-2.1 eV. 39,402][43] The greater energy barrier in between electrode and the active material within an OPV restricts charge carrier movement from the active layer towards the electrode.This may result in poor performance of the device during its operation indoors.5][46][47][48] Transparent conducting electrodes (TCEs) based on a range of materials have indeed been produced in relation to numerous semiconducting interlayers.0][51][52][53][54] Finally, since the photon absorption abilities of various layers (particularly the active layer) are strongly dependent upon their thickness, the performance of a OPV may be modied by optimizing the thickness values of different layers of the device.6][57][58][59][60][61][62][63][64][65] A detailed review reveals that, although we have achieved over 35% PCE from an IOPVs via extensive research, 38,66 the commercialization of IOPVs has not yet been achieved because of several drawbacks such as shorter lifespan and lower stability.Therefore, a detailed review of this topic will be very helpful to identify the challenges that must be addressed in the near future.
In this extensive review, we deeply examine a range of methodologies utilized in the development of highly efficient IOPVs.Our investigation includes a detailed analysis of various photovoltaic components used in IOPVs' active layer.We also investigate the incorporation of different donor-acceptor semiconductors into this active layer, as well as the evolution of many interlayers designed for the best IOPV performance.We also extensively investigate the application of optical simulation techniques to enhance device architecture.Concluding our study, we provide a comprehensive discourse on the commercial potentials of IOPVs, coupled with insights into their promising future prospects.

Various indoor light sources
The light source is an essential component of an indoor light energy harvesting system.We have already mentioned that various types of light sources are used as major illuminators of indoor environment.These light sources differ in their wavelength ranges and the intensity of their irradiance spectra, allowing them to be distinguished from one another. 16As depicted in Fig. 1a, the irradiance spectrum of the CFL tube light reveals notable peaks around ∼400 nm, ∼450 nm, ∼550 nm, and ∼600 nm, while the cold white LED light exhibits pronounced peaks at approximately ∼450 nm and ∼550 nm.In contrast, the irradiance spectra of halogen and incandescent bulbs display a gradual and consistent increase across the wavelength span of 300-900 nm.Additionally, the wavelength distribution of light emitted by these distinct sources varies.Notably, the LED light source demonstrates a broader and more continuous dispersion of energy compared to the CFL.Moreover, there are distinctions in the light quality generated by the different sources; they produce light with differing irradiance power intensities while maintaining the same luminance value.Conversely, natural sunlight exhibits a broad range (wavelength) of irradiance spectra (Fig. 1b).As a consequence, OPVs typically demonstrate distinct spectral responses to various light sources when held at a constant luminance value.This phenomenon gives rise to varying levels of harvested light energy by a PV panel, depending on the specic articial light source it operates under at a xed luminance value.Consequently, the creation of customized OPVs tailored for indoor usage presents a challenging endeavor.The optimization of diverse OPV parameters is imperative to accommodate indoor lighting conditions.The device's design must be adept at achieving efficient operation under the prevalent illumination of frequently employed indoor light sources.Recent years have witnessed a concerted effort from researchers to optimize numerous device parameters for indoor applications.Additionally, the pursuit of synergistic semiconductor materialscharacterized by broader absorption spectra that align well with the irradiance spectra of commonly utilized articial light sources-has emerged as a central objective in the quest to produce exceptionally efficient OPVs tailored for indoor.

Performance measurement of OPVs under indoor light sources
It is evident that regular testing of OPVs is imperative.Hence, creating a simulated optimal testing environment for indoor light exposure is crucial for obtaining precise outcomes.It's important to acknowledge a fundamental distinction between outdoor and indoor lighting conditions.Unlike outdoor condition where PV devices directly receive sunlight, indoor environments frequently lack direct sunlight.Consequently, the signicance of diffused light, resulting from reection off various surfaces, becomes heightened as it contributes to powering indoor PVs (Fig. 2a-c). 67o establish a suitable testing environment for PV devices during experimental trials, the mitigation of uneven light distribution holds paramount importance.In one word standardization of test conguration for developing realistic indoor light conditions is highly needed.In this context, recent work by Kim et al. focused on rening the measurement system by optimizing the spacing between the light source and the device platform. 67Their objective was to establish an optimal indoor lighting setup.The study's outcomes underscore that netuning the distance between the light source and the test device can yield the desired diffused light effect (Fig. 2d and e). 67otably, the researchers identied that achieving a more accurate assessment of the PV device's performance variation under different light sources is attainable by considering a constant irradiance power intensity value for the light sources, as opposed to a xed luminance value.This approach is particularly insightful since diverse indoor light sources exhibit varying irradiance power intensity values for a given luminance level (Fig. 2f).
In contrast, Saito et al. noted that readily available indoor light sources in the market can experience uctuations in luminance when powered by an AC source (Fig. 2g). 68This variability has the potential to introduce uctuations in the results of PV device tests.To address this issue, the researchers introduced a method aimed at mitigating the impact of these luminance uctuations on the J-V measurements of PV devices (Fig. 2h). 68Furthermore, their study involved the creation of an LED light irradiation apparatus, designed to enhance the dependability and reproducibility of J-V measurements for PVs.This equipment demonstrated remarkable temporal stability in illuminance and uniformity across the test plane, fullling the rigorous requirements set forth by the Class A solar simulator standards prescribed in IEC 60904-9.
In 2021, Hou and colleagues introduced a rened measurement procedure to enhance the precision of characterizing OPVs under indoor lighting conditions. 69Their study involved a comprehensive series of experiments aimed at dissecting the sources of errors encountered in indoor PV measurements.The researchers effectively demonstrated that the temporal stabilities and homogeneity factor of commonly utilized LED and FL light sources can yield satisfactory outcomes for PV measurements, provided both factors are rigorously assessed prior to conducting measurements.To achieve accurate results, they emphasized the necessity of calibrating spectral irradiance and light intensities using a precise spectrometer, while discouraging the utilization of lux meters.The research encompassed an evaluation of cell area and the area ratio of the aperture to the cell.Consequently, they recommended employing cells of 1 cm 2 or larger, accompanied by slightly smaller apertures, for optimal PV measurements.Furthermore, the researchers stressed the meticulous elimination of stray light effects, encompassing light reection, and scattering caused by measurement apparatus, to minimize potential interference in PV measurements. 69he PCE of a PV device can be estimated by utilizing the following equation (eqn (1)) 69 Fig. 1 (a) Irradiance spectra of different indoor light sources; 16 (b) solar spectra (AM1.5G). 16here P out is the output power which can be estimated by the following equation (eqn (2)) 69 and P in is the power intensity of incident light, which can be estimated by eqn (3), 69 where E l is spectral irradiance (W m −2 nm −1 ), and l is the wavelength.
The value of J SC can be achieved in two ways, one is from J-V characteristics curves and another is by calculating from the external quantum efficiency curve (EQE(l)) (eqn (4)).According to eqn (4), the short circuit current density (J SC,EQE ) calculated from EQE(l) can be expressed as, 69 where (N l (l) = E l × l/hc, considering E(l) as energy associated to a particular l, h is Planck constant and c is the speed of light) is the photon numbers per nanometre per square centimetre.It is evident from eqn (1)-(3) that precise estimation of J SC is crucial for accurately determining the PCE value of a PV device under indoor lighting conditions.When determining J SC from the measurement of J-V characteristic curves, the estimation of J SC can be inuenced by several factors such as leakage current, contact losses, non-ideal diode behaviour, measurement artefacts etc. potentially leading to both overestimation and underestimation of J SC .This may results estimation of inaccurate device PCE.Therefore, Hou et al. has recommended that J SC,EQE of the OPV is essential for evaluating the reliability for the J SC obtained from the PV measurement.Therefore, the EQE(l) curves of the cells and the spectral characteristics of the incident lights must be provided and also the deviations between J SC and J SC,EQE should be low, e.g., <5%. 69he comprehensive review reveals that while establishing a standardized protocol for assessing the performance of OPVs under indoor lighting is crucial for precise determination of device performance metrics, only a limited number of endeavours have been undertaken thus far.A concentrated emphasis on addressing this specic area is greatly warranted in the coming times.

Various donor and acceptor materials for IOPVs
Distinct operational processes between indoor and outdoor OPV cells arise primarily from disparities in light intensity, spectral composition, and environmental variables.In the case of outdoor OPVs-integrated into diverse exterior surfaces like building facades, windows, and wearables to produce renewable energy for an array of applications-the light source comprises natural sunlight, characterized by its wide spectrum and heightened intensity in contrast to indoor illumination.Therefore, the selection of specic active materials (donors and acceptors) becomes crucial to ensure absorption across a broader wavelength range.Moreover, the design of outdoor cells necessitates the incorporation of highly durable materials capable of withstanding the rigors of an exposed environment.Conversely, IOPVs, apt for low-power uses like energizing compact electronics, sensors, or energy-efficient lighting in indoor settings, predominantly function within the realm of articial illumination-examples being LEDs, FLs, and incandescent bulbs.This articial light possesses lesser intensity in comparison to natural sunlight.Thus, the judicious selection of active materials with a narrower absorption band and elevated absorption coefficients becomes pivotal in the craing of notably efficient IOPVs.To develop a suitable active material for highly efficient IOPVs, appropriate donor and acceptor materials must be developed.Several factors must be considered for this purpose, including good spectral matching in between active layer's absorption spectra and the light's illuminance spectra, adjusting the energy levels of donor and acceptor components (to acquire the band gap of the photo active layer within 1.9-2.1 eV) for achieving comparatively elevated opencircuit voltage (V OC ) in indoor, and good electrical charge transport capacity.As donor materials, a variety of organic polymers and small molecules (Fig. 3) were developed to satisfy all criteria.In addition, various fullerene (Fig. 4) and nonfullerene (Fig. 5) materials-based acceptors have also been developed.In terms of the active materials, the entire family of IOPVs can be classied into two types; fullerene-based IOPVs and non-fullerene-based IOPVs.

Fullerene acceptor-based IOPVs
Polymer donors and fullerene acceptors are used to develop active layers of rst-generation OPVs.So far, there have been relatively few organic semiconducting materials like as poly(3hexylthiophene-2,5-diyl) (P3HT), poly [[4,8-bis[(2-ethylhexyl) and poly[(5,6-bis(2-hexyldecyloxy)benzo[c] [1,2,5]thiadiazole-4,7-diyl)-alt-(5,50-(2,5-diuoro-1,4-phenylene)bis(thiophen-2-yl)] (PDTBTBz-2F anti ) have been used as donors, whereas phenyl-C61-butyric acid methyl ester (PCBM) and indene-C60 bisadduct (ICBA) have been used as acceptors for these types of IOPVs.The performance parameters of various fullerene-based IOPVs (i.e., binary) reported earlier are summarized in Table 1.In the early stages of IOPVs development, attaining higher V OC posed a signicant challenge.The V OC value, measuring at a mere 0.43 V for IOPVs based on PC 60 BM, hindered their overall efficiency with a maximum PCE of only 9.59%.This limitation stemmed from the decreased energy level associated with the lowest unoccupied molecular orbit (LUMO) of the conventional PC 60 BM, as highlighted in Table 1.In response, a solution emerged by introducing a novel fullerene acceptor named ICBA.This breakthrough involved attaching two substitution groups onto the fullerene ball, effectively addressing the previously mentioned issue. 55,70,71t was then observed that ICBA-based IOPVs could exhibit higher V OC (0.73 V) and PCE (13.7%) because of the high energy value associated with their LUMO level (Table 1).Other donor polymers, including such PTB7, have also been identied to have comparable PCE value.PTB7 has a greater absorption range (400-750 nm), although P3HT's absorption range is substantially smaller (350-650 nm).As a result, PTB7:PCBMbased devices may generate higher photocurrents.In comparison to P3HT:ICBA-based devices, PTB7:PCBM-based devices have a lower V OC and ll factor (FF).However, these two types of devices are equivalent in terms of efficiency.Aside from PTB7, another polymer donor material known as PTB7-Th has shown to work well in IOPVs applications.Both PTB7 and PTB7-Th have an identical backbone conjugated structure.The chemical ligands attached to the benzodithiophene groups differ only in nature.In PTB7, it's an ether group, and in PTB7-Th, it's a thiophene group. 72In 2015, Mori and coworkers have used PTB7-Th:PCBM as an active layer of an IOPVs. 73The OPV was subjected to testing under an illumination of 186 lx from an LED source, revealing a noteworthy PCE of approximately 10.6%.Furthermore, an upper limit for the potential PCE was approximated at 21.3% for the same OPV (PTB7-Th:PC 70 BM) under the conditions of 186 lx LED illumination.Later, Marsal et al. have able to achieve ∼13.9% PCE (under 1000 lx LED lamp) Fig. 3 The chemical structures of numerous donor materials utilized in indoor OSCs.
Fig. 4 The chemical structures of several fullerene-acceptor materials utilized in indoor OPVs.
value from a PTB7-Th:PCBM active layer based indoor OPV through the introduction an efficient ETL. 74nother instance of polymer:fullerene-based IOPV is based on a donor polymer named PCDTB-T. 71This polymer incorporates a carbazole donor unit, a benzothiadiazole acceptor unit, and two thiophene units as connecting elements.The inclusion of PCBM facilitates the generation of a notable V OC ; in indoor conditions, this V OC can achieve up to 0.7 V, a value that ranks among the highest observed for polymer:fullerene devices.Furthermore, devices based on PCDTB-T:PCBM exhibit an elevated shunt resistance (RP) of approximately kU cm 2 , providing an advantageous factor for achieving enhanced FF in environments with low light.In the course of this study, the researchers fabricated large-scale modules spanning an area of 100 cm 2 and achieved a commendable PCE of 11.2%.
The innovation of new donor polymers for indoor applications improved the performance of indoor PCEs even further.Shim and colleagues, for example, created a donor polymer called PDTBTBz-2F anti , 75 which has an absorption window that corresponds to indoor light.This polymer also has crystalline nano-brillar morphology with such a preferential face-on orientation for p-p stacking, allowing for improved electron injection and the construction of efficient thick lm devices capable of enhancing light absorption and lowering leakage current.Because of these benets, this polymer can achieve a high efficiency of 23.1% under a 1000 lx LED light.Surprisingly, under the 1 sun condition, the efficiency of OPV devices based on this polymer:fullerene combination is just 6.9%.This nding suggests that materials that aren't suited for outdoor OPV applications could be good for inside illumination.
A small molecule donor and a fullerene acceptor are used in another form of OPV.Unfortunately, there have been limited studies on the application of small-molecule donor and fullerene acceptor-based OPVs for low-intensity indoor light harvesting.Tsoi et al. revealed in 2018 that they harvested energy from a 1000 lx FL lamp using a benzodithiophene terthiophene rhodamine (BTR) small molecule as a donor and a PC 71 BM acceptor-based OPV. 76They chose this material as the donor because of its interesting morphology (arising from the special arrangement of the alkyl chain) and sufficiently higher optical energy band gap (1.80 eV) (suitable for indoor light harvesting).They were able to achieve a balance between crystallization and phase separation by optimizing the active layer's solvent vapour annealing duration, and they were able to produce a very high PCE (>28%) while the device was operated under 1000 lx FL lamp.Additionally, the device produced a very high maximum power density value (78.2 mW cm −2 ).Continued research into these sorts of donor and acceptor material combinations is likely to result in IOPVs with greater PCE and longer lifespans.

Non-fullerene acceptor-based IOPVs
In the realm of OPVs, a recent and remarkable breakthrough has emergedthe advent of a novel class of acceptor materials known as non-fullerene acceptors.Unlike traditional fullerene acceptors, which suffer from limited absorption in the visible spectrum, non-fullerene acceptors offer a solution to this challenge.Moreover, their unique feature lies in the ability to nely adjust their electronic structure, enabling the attainment of desired energy band gaps tailored to different articial light sources.This exibility facilitates the modulation of V OC , a crucial parameter in OPV performance.Importantly, nonfullerene acceptors exhibit the potential to exhibit high light absorption within the visible range, coupled with the capacity to ne-tune their frontier molecular orbital levels.This characteristic proves invaluable in enhancing V OC , particularly under the constraints of low-intensity indoor lighting conditions, by minimizing energy losses.As a result of these exceptional attributes, non-fullerene acceptors have emerged as highly promising contenders for the advancement of IOPVs.During the last few years, several well-behaved non-fullerene acceptors such as 3,9-bis [5,6- 8][79][80][81][82][83][84] In this subsection, we shall discuss the recent studies on the application of various non-fullerene acceptor-based IOPVs.The performance parameters of various non-fullerene-based IOPVs (binary) reported earlier are summarized in Table 2.
Because of its broad (1.80 eV) optical energy band gap, IO-4Cl is one of the best non-fullerene acceptors for IOPVs to harvest light energy generated by LEDs.In 2019, Hou and coworkers developed this fullerene-free semiconductor, which was designed as an acceptor-donor-acceptor structure. 80They combined it with a polymer donor known as poly[(2,6-(4,8-bis(5- Review RSC Advances ] (PBDB-TF) to create a photo-active layer for indoor OPVs.Under the illumination of a 1000 lx (2700 K) LED, an IOPV with a 1 cm 2 active layer exhibited remarkable attributes, boasting an elevated PCE of 26.1% and a notably higher V OC of 1.10 V. Impressively, this OPV showcased exceptional stability, maintaining consistent photovoltaic performance throughout 1000 hours of uninterrupted LED exposure.Within the core of IO-4Cl, the electrondonating fragment molecule ITIC assumes a pivotal role.Constructed around a stiff core comprising two sp 3 -hybridized carbon atoms, this molecule's propensity for self-aggregation is mitigated by the steric hindrance introduced by aromatic side chains.The incorporation of fused rings further curbs rotational perturbations.Consequently, this conguration substantially reduces reorganization energy and mitigates voltage loss when the organic photovoltaic device operates under the conditions of low-intensity indoor lighting.
Another noteworthy non-fullerene acceptor material goes by the name of IT-4F.This material, like ITIC, is founded upon the same foundation, with the addition of four uorine atoms at its terminal group.These uorine atoms introduce an electronattracting inuence, which contributes to heightened crystallinity and enhanced p-p stacking within the active layer.Furthermore, they play a role in shiing the acceptor's LUMO and HOMO levels downwards, thereby elevating the FF of the device.When employed as an acceptor in OPVs, IT-4F exhibited impressive performance, achieving a PCE exceeding 14% under standard 1 sun illumination.However, owing to a reduction in voltage, OPVs utilizing the IT-4F acceptor demonstrated inferior performance in scenarios of low-intensity indoor lighting.For example, Hou and colleagues used PBDB-TF:IT-4F as the active layer to build very efficient IOPVs, achieving a maximum PCE of 20.8% for a 1000 lx 2700 K LED illumination. 81Although achieving a PCE surpassing 20% and showcasing consistent performance throughout prolonged operation under conditions of low-intensity indoor lighting, the inability to achieve an even higher PCE value can be attributed to the lower V OC of 0.71 V.This lower V OC could potentially be traced back to the comparatively reduced optical energy bandgap associated with IT-4F.
Recently, Yin et al. reported a record high PCE (>30%) from a non-fullerene based IOPVs. 36The device was built around a PBDB-TF donor and a Y6O acceptor, both of which are based on 2,2 ′ -((2Z,2 ′ Z)-((12,13-bis(2-ethylhexyl)- dimalononitrile (Y6) by substituting an alkyl chain at the b-position of the merged thiophene unit with an alkoxy side chain.In comparison to the indoor illumination spectrum, the absorption range of Y6 is oen up to 940 nm, which is excessively red-shied.As a result, the alkoxy substitution aided to blue-shi the acceptor's absorption by increasing its HOMO and LUMO levels.The device has an extremely high V OC (0.84 V) and FF (0.76%), as well as a record-breaking PCE value.The same team has designed FCC-Cl, a new high-performance nonfullerene acceptor with a desirable optical band gap for IOPVs, by coupling a weak electron-donating core with a moderate electron-withdrawing end group.Because of the high crystallinity, wide energy band gap and high absorption coefficient of FCC-Cl, the FCC-Cl acceptor-based OPVs demonstrated a very high PCE (28.8%) under the light of 500 lux LED (2600 K). 85 Thick-lm devices based on FCC-Cl were also created, and devices with a thickness of 300 nm may still achieve a PCE of 26.5% under LED at 1000 lx.IOPV devices' high thickness tolerance is a desired attribute for roll-to-roll large-area printing processes.
A unique donor-acceptor combination (polymer donor and polymer non-fullerene acceptor) was been employed as an active layer for IOPVs.Liu   77 Considering the donor's extremely high HOMO level, the device produced extremely high V OC .Furthermore, because of the polymer nature of the donor and acceptor substances, the device displayed greater mechanical exibility and stretchability.
In 2022, Yan et al. have reported a series of large-bandgap (>1.70 eV) NFAs named FCC-Cl-C8, FCC-Cl-4Ph and FCC-Cl-6Ph by modifying the alkyl side chains with alkylphenyl chains partially or completely. 86In their work it has been observed that the bulky alkylphenyl side chains can nely tune the absorption properties of the NFAs and also affect their morphological properties.Interestingly it has been observed that the best-performing NFA is the one (named FCC-Cl-4Ph) with partial alkyl and alkylphenyl substitutions, which blue-shi the absorption of the NFAs while minimizing the negative morphological effect of the bulky alkylphenyl chains.As a result, FCC-Cl-4Ph can achieve excellent indoor efficiencies over 29% under a 3000 K LED lamp at 1000 lx and show better solution processability over FCC-Cl-C8.More importantly, FCC-Cl-4Ph can maintain high indoor performance (29.7-26.8% at 1000 lx) under a wide range of indoor lighting spectra (2600, 3000, 4000, and 6500 K LED lamps), which should be due to the blue-shied spectra of FCC-Cl-4Ph and better matching with various indoor conditions.This work reveals an interesting structure-property relationship and offers useful strategies for the further design of NFAs toward efficient IOPV devices.
Hou and coworkers, recently a designed and synthesized a series of polymers (PB3, PB4 and PB5) based on thiadiazole (TDZ), 4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b:4,5-b ′ ] dithiophene (BDT-T) and uorinated BDT-T (BDT-T-2F) units based on a random polymerization strategy. 37The terpolymers have demonstrated wide optical bandgaps larger than 2.0 eV.Compared to the host polymer PB2, the terpolymers have exhibited downshied energy levels and enhanced crystallinities, which show much lower energetic disorders.Aer blending with a wide bandgap non-fullerene acceptor FTCC-Br, the optimized terpolymer have shown a much faster charge transfer rate than PB2.Importantly, the OPV cell based on PB3:FTCC-Br has achieved a high PCE of over 15% with an V OC of 1.06 V under 1 sun condition.The PB4:FTCC-Br-based cell has demonstrated a PCE of 14.79% with a high V OC of 1.09 V. Furthermore, the PB3:BTP-eC9-based cell has exhibited a PCE of 18.28%.Besides, the PB4:FTCC-Br-based cell with an effective area of 1.0 cm 2 has exhibited a PCE of over 31% under 2700 K illumination of 1000 lx.The results indicate that the ternary copolymerization strategy is an effective way to ne-tune the opto-electronic properties of highly efficient polymer donors for versatile photovoltaic applications.Later the same group have achieved over 33% PCE value from PB2:FCC-Cl active material based IOPV under concentrated indoor light. 87Additionally, the device has exhibited superior stability (extrapolated T 80 over 30 000 h) under indoor light.
The correlation between molecular structure and photovoltaic performance is lagging for constructing high-performance IOPV cells.Recently, Hou et al. investigated this relationship in depth by employing two medium-bandgap NFAs.The newly synthesized NFA of FTCC-Br exhibited a similar bandgap and molecular energy level, but a much stronger dipole moment and larger average electrostatic potential (ESP) compared with ITCC.Aer blending with the polymer donor PB2, the PB2:ITCC and PB2:FTCC-Br blends exhibit favorable bulk-heterojunction morphologies and the same driving force, but the PB2:FTCC-Br blend exhibited a large ESP difference.In OPV cells, the PB2:ITCC-based device produces a PCE of 11.0%, whereas the PB2:FTCC-Br-based device gives an excellent PCE of 14.8% with an V OC of 1.05 V, which was the highest value among OPV cells with V OC values above 1.0 V.When both acceptor-based devices worked under a 1000 lx of 3000 K light-emitting diode, the PB2:ITCC-based 1 cm 2 device yields a good PCE of 25.4%; in contrast, the PB2:FTCC-Br-based 1 cm 2 device outputted a record PCE of 30.2%.These results suggested that a large ESP offset in photovoltaic materials was important for achieving high-performance OPV cells. 88

Multi donor-acceptor-based IOPVs
Traditional binary donor-acceptor-based active layers oen face challenges due to inadequate crystallinity, suboptimal morphology, and reduced absorption coefficients.These limitations hinder the attainment of elevated J SC , and consequently, hinder the overall PCE achievable in indoor applications.To address this concern, efforts have been directed towards enhancing the active materials' characteristics in IOPVs through the incorporation of multiple donors and acceptors.This innovative approach offers certain advantages, including the potential for thinner device proles, circumvention of current-voltage matching constraints, and more.Nonetheless, achieving optimized absorption and charge-injection capabilities necessitates precise tuning of their bulk heterojunction (BHJ) morphology.Moreover, parameters such as electrical energy levels, bandgap, solubility, and compatibility between various materials must be thoughtfully considered during the device fabrication process.Table 3 summarizes the performance characteristics of several multiple donor-acceptor-based IOPVs previously described.
So et al. created a highly efficient ternary IOPV in 2018 using PCDTBT and PDTSTPD as donor substances and PC 71 BM as the acceptor material. 89Under the irradiation of a 2700 K, 300 lx FL lamp, the ternary OPV had a maximum PCE of 19.8% (Fig. 6a).The ternary OPV had a very high J SC value, which was mostly due to the active layer's absorption window being expanded up to the near infrared range.To enhance device performance even more, the active layer was annealed for 30 s aer spin coating.Under the same illumination conditions, the device (solvent vapour annealing-treated) exhibited 20.8% PCE value along with a V OC , FF, and J SC of 0.73 V, 63.5%, and 33.3 mA cm −2 respectively (Fig. 6a).Surprisingly, when illuminated by other light sources with greater color temperatures, the same device worked very inadequately (Fig. 6b), leading to incompatibilities between the light source's irradiance spectra and the active layer's absorption spectra.
Recently, Shim et al. have reported the utilization of a quaternary bulk heterojunction to harvest indoor light energy.Because the HOMO and LUMO values of the component materials were well matched, they selected PCDTBT and PTB7 as donors and PC 61 BM and PC 71 BM as acceptor materials for the active layer (Fig. 6c) (Fig. 6d).They showed that the performance of a quaternary IOPVs is largely reliant on the blend ratio of the component materials of active layers, and that with an optimal blend ratio, a maximum PCE value from a quaternary IOPVs can be reached (Fig. 6e and f).Under the illumination of a 500 lx white LED with a composition ratio of 5 : 5 : 3 : 12, they achieved a maximum PCE value of 10.6% (PCDTBT : PTB7 : PC 61 BM : PC 71 BM).At this ideal composition ratio, the device exhibited very high shunt resistance and low series resistance, resulting in considerable charge extraction under low-intensity light conditions. 65esides opaque IOPVs, highly efficient quaternary active material-based semi-transparent indoor IOPVs have also been reported.In 2019, Ko and coworkers developed a semitransparent IOPVs based on quaternary blends (PBDB-T:PTB7-Th:ITIC-Th:PC 70 BM) (Fig. 6g and h).They proved the device's practical applicability in four-terminal (4T) tandem OPVs. 90The semitransparent quaternary OPV demonstrated a very high PCE value (15.46% when illuminated by a 1000 lx LED light) (through the minimization of energy loss and maximization of absorption coefficient) while keeping excellent transparency and the ability to incorporate multiple colors (Fig. 6i).
Recently, Ko and coworkers discussed the sequential deposition method, as an alternative strategy for the facile realization of high-performance multicomponent BHJ OPVs for indoor applications.The sequential deposition improved the collection of indoor light, modied the molecular alignment of polymers, and reduced the hole trap-state density and charge recombination loss in the quaternary BHJ lms.The sequentially processed quaternary OPVs exhibited superior PCEs approaching 26.06% under diverse indoor irradiation environments, while neither compositional optimization nor additional treatment steps were implemented.The sequential deposition method can be a platform to simplify the fabrication process of multicomponent BHJ OPVs while exploiting the advantages offered by the multiple materials and their synergistic benets to comply with the requirements of efficient indoor applications.Further investigation of the molecular evolution during sequential deposition can enrich this methodology and is currently underway. 91he review study discerns that despite the considerable promise of this strategy in advancing highly efficient IOPVs, only a scant number of endeavors have been undertaken thus far.

Utilization of interlayer (HTL, ETL)
In the realm of OPVs, two distinctive types of interlayers come into play.The rst is the HTL, strategically positioned between the device's anode and the active layer.The second is the ETL, situated between the device's cathode and the active layer.The integration of these interlayers serves multifaceted purposes, encompassing the mitigation of defect states and potential surface charge recombination, as well as the reduction of energy barriers existing between the electrode and the OPV's active layer.As the landscape stands, diverse semiconducting materials, spanning both organic and inorganic realms, have been harnessed to fulll HTL and ETL roles in various OPV congurations.The chemical structures of various materials used as ETL and HTL of various IOPVs are presented in Fig. 7.In this subsection, we will discuss the development of various HTLs and ETLs for the improvement of various IOPVs.
In 2013, Hegger et al. tried to optimize the performance of a DTS(FBTTh 2 ) 2 :PC 71 BM active layer-based OPV operating under various light sources having variable intensities through the regulation of the thickness of its ETL formed by calcium (Ca). 92They observed that rst-order charge recombination regulated the J-V characteristic curves between the short-circuit and maximum power point (MPP) at an appropriate ETL thickness, and that this control was then translated to biomolecular charge recombination in between MPP and open-circuit circumstances.Because of the lack of Shockley-Read-Hall recombination and strong charge-collection efficiency, the device had a very high FF value (73%).
In 2016, Lechêne et al. studied the utilization of ethoxylated polyethylenimine (PIEE) as an ETL for IOPVs (PCDTBT:PC 70 BM active-layer-based) (Fig. 8a). 93They demonstrated that maximum PCE from an IOPVs can be achieved through device optimization for a particular light source.More specically, minimization of dark current of an IOPVs is essential to achieve enhanced PCE from an indoor OPV.The PCE of an OPV optimized in the 1 sun condition was 6.2%, while the PCE of the very same device under low-intensity indoor light was 5.2% (Fig. 8b).Interestingly, when the OPV was tuned for indoor light, it showed 7.6% PCE under articial indoor light illumination (Fig. 8c).
Shim and colleagues then investigated the relationship between the ETL's electrical characteristics and the parasitic resistance of an IOPV (PEIE ETL and P3HT:ICBA active-layerbased). 94PEIE is an insulator but it has an amine group, which can donate electrons on the surface of the electrode and form dipoles.The ensuing dipole moment lowers the work function on the conductor surface, causing a vacuum level downshi.The thickness of the ETL was adjusted by varying its thickness from 1.7 to 22.8 nm.Under the 1 sun condition, PCE (maximum) value of 4.7 ± 0.3% was acquired for a 2.2 nm thick PEIE layer.Additionally, when the thickness of the PEIE lm rose, the PCE and FF of the OPV steadily decreased due to the rise in R S .Under the irradiation of a 500 lx LED light, however, the OPVs with a thicker PEIE layer (8.5 nm) efficiently harvested photon energy (PCE z 13% and FF > 73%).The study concluded that a distinct cell design method is required to maximize OPV performance under low-intensity indoor lighting.
In 2019, the same group reported the application of an ultrathin ZnO layer (modied by PEIE) as a highly efficient ETL of an inverted structured OPV (P3HT:ICBA active layer based). 95nder the irradiance of a 1000 lx LED lamp, an OPV with only a ZnO nanoparticle-based ETL could have a very poor PCE (5.6%) due to the formation of a Schottky barrier caused by energy level inconsistency between the insufficiently low work function of the ZnO nanoparticles and the electron affinity of the ICBA.Under the same illumination circumstances, an OPV with a PIEE-modied ZnO layer as the ETL had a very high PCE value (14.1%).It was suggested that the PEIE adjustment created a dipole moment, which led in an adequate work function decrease and a remarkable improvement in the IOPVs performance (Fig. 8d and e).
Very recently, Ylikunnari and coworkers tested the potential of ZnO and SnO 2 as the ETLs in exible OPVs (PV2001:PC 61 BM active-layer-based), for operating under low-intensity indoor light. 96They observed that ZnO ETL-based OPVs could exhibit a higher PCE than a SnO 2 ETL-based OPV under the 1 sun condition.However, when exposed to low-intensity indoor light, the SnO 2 ETL-based OPVs (PCE > 13% at 800 lx (i.e., a FL lamp)) performed better than the ZnO ETL-based OPVs.They concluded that the performance level of ETLs under various illuminating conditions is correlated to the adjustment of barrier height (related to charge transport) due to the change in illumination conditions (especially the presence or absence of UV light).ZnO is known to be UV-light sensitive; therefore, under the 1 sun condition, the UV light reduced the energy barrier (related to electron transport) and improved the electron extraction ability of the ZnO layer.Consequently, the ZnO ETLbased OPV exhibited better performance under the 1 sun condition.By contrast, the low-intensity indoor light is UVregion free; therefore, during the indoor operation of ZnO ETL-based OPV, the effect of UV light irradiation was missing, so the device exhibited poor performance.Interestingly, for SnO 2 , this type of effect (due to UV irradiation) was missing.As a consequence, under ambient light conditions, SnO 2 ETL acquired more electrons, making a much more potential candidate as ETLs for indoor applications over ZnO.
According to Marsal and colleagues, the performance of an inverted structured OPV is greatly inuenced by lighting conditions. 74For this purpose, they fabricated an inverted structured OPV (PTB7-Th:PC 70 BM active-layer-based) by employing three different types of solution-processed ETLs (PFN, TiO x , and ZnO).It was found that the OPV with poly [(9,9bis(3 ′ -(N,N-dimethylamino)propyl)-2,7-uorene)-alt-2,7-(9,9-dioctyluorene)] (PFN) as the ETL had the greatest PCE (10.55%) value under 1 sun condition and the lowest performance under low-intensity LED light (250-2000 lx 2700 K) illumination.The ZnO ETL-based OPV had a lower PCE (10.03%) under the 1 sun condition, but it had improved indoor efficiency with such a PCE of 13.94% under a 1000 lx LED lamp and 16.49% under a 1750 lx LED lamp (Fig. 8f and g).The result was further demonstrated on the basis of the variation of parasitic resistance of various ETL-based OPVs.
Yin et al. have explored the importance of energy band alignment between the ETL and acceptors in the operation of an IOPVs. 36They employed PM6:Y6-O as an active layer and 2,9-bis [3-(dimethyloxidoamino)propyl]anthra[2,1,9-def:6,5,10-d ′ e ′ f ′ ]diisoquinoline-1,3,8,10(2H,9H)-tetrone (PDINO) or PFN as the device's ETL.The PFN and PDINO ETL-based OPVs demonstrated similar PCE values (16.1% (PFN) and 16.4% (PDI-NO)) under 1 sun condition, however the devices behaved differently under low-intensity indoor lighting.The PDINO ETL-based OPV demonstrated extremely high PCE (30.8%) when illuminated with a 1650 lx LED, but the PFN ETL-based OPV had lower PCE (22%) (Fig. 8h and i).They suggested that the difference was due to the variation in band alignments in the two devices.The energy associated with the HOMO level of PDINO and PFN is −6.21 eV and −5.61 eV respectively.As a consequence, PDINO could prevent the movement of holes more efficiently than the PFN layer, resulting in decreased leakage current for low-intensity light illumination.
Recently, Kim et al. fabricated ZnO and gallium (Ga)-doped ZnO (GZO) ETL-based inverted structured OPVs with PBDB-T:PC 70 BM active layer and evaluated them under LED (1000 lx). 97To optimize the doping concentration, they varied the concentration of Ga in the GZO.The ndings demonstrated that only by doping the ETL of the inverted structured OPV, the PCE may be signicantly enhanced.Under a 1000 lx LED illumination, the device using undoped ZnO as the ETL showed a maximum of 15.56% PCE.The OPV with Ga-doped ZnO as the ETL with an optimized concentration of Ga (2 at%) exhibited a maximum of 23.42% PCE under a 1000 lx LED.
][100][101] Generally, PEDOT:PSS is used as the HTL of IOPVs because of its easy processability, water stability, superior hole transport ability, and desired work function (approximately 5.2 eV).However, it has a number of signicant disadvantages, including high acidity, UV radiation sensitivity, and a high price.The device's lifespan is signicantly shortened due to its greater acidity and susceptibility to UV rays.Therefore, recently Kim et al. tried to use lower-acidic PANI:PSS as the HTL of IOPV. 44,46They observed that the thin lm formed by PANI:PSS could exhibit a very high transmission level and had a work function value around 5.15 eV.Furthermore, given its lower-acidic nature, the OPV based on PANI:PSS HTL could have a much longer lifespan than a PEDOT:PSS HTLbased IOPVs 44 (Fig. 9a-c).
Furthermore, Kim et al. recently discovered that the performance of an IOPVs (PANI:PSS HTL and P3HT:ICBA active layer) is strongly inuenced by the doping concentration of its HTL. 46he PANI:PSS HTL might have a better conductivity at an optimal doping concentration.Because of the HTL's improved charge transport capacity, the OPV could achieve an extraordinarily high PCE (8.1%) under the irradiation of a 500 lx LED lamp (having an optimal concentration of the doping reagent) (Fig. 9d-f).
Besides the organic semiconductors, an inorganic semiconductor was also tested as the HTL of IOPVs.In 2020, Shim et al. studied the potential of tungsten oxide (WO 3 ) as the HTL of an IOPVs. 48They considered WO 3 as an HTL owing to its high work function (z5.5 eV), low electron affinity, and excellent thermal stability.They discovered that the IOPVs (WO 3 HTLbased) could show a very high PCE (13%) under the irradiation of a 1000 lx LED due to the excellent hole selectivity (caused by the decreased electron affinity) of the WO 3 layer (Fig. 9g-i).

Optimization of device architecture through optical simulation
It is an accepted fact that the performance level of a PV device is strongly dependent on various device parameters such as the thickness of various layers, surface morphology of each layer, and absorption coefficient of the active layer, charge carrier mobility, energy band gap, recombination coefficient, and contact resistance between various layers.Therefore, in the past few years, some researchers have tried to optimize these device parameters to achieve maximum PCE. 56,57,59It is clear that a purely experimental approach is not very efficient for optimizing device architecture to achieve a better performance level because it will be time-consuming and expensive.Therefore, an alternative approach is needed to address this concern.A combination of experiments and device simulation studies can be a good option, as it can save time and money.Device modeling and simulation can help to explore the device operation mechanism and interaction between various layers of PV devices based on the basic concepts of physics.This is also a very useful and cost-effective tool to nd undiscovered device concepts for further development.For the last few years, some people have tried to optimize various parameters of IOPV devices via modeling and device simulation studies to achieve better performance. 56,57Through meticulous review studies, researchers embarked on a quest to comprehend the intricate interplay of diverse factors shaping the overall performance dynamics of IOPV devices.To elucidate their operational mechanisms, they turned to Finite-Difference Time-Domain (FDTD) simulations.These investigations were underpinned by the utilization of the potent Lumerical FDTD soware, renowned for its prowess in optical modeling of photovoltaic systems.In this pursuit, the simulation process commences by ascertaining the optical attributes of the various layers constituting the photovoltaic device.This is achieved through the incorporation of experimentally derived frequency-dependent complex refractive index values for these layers.The mesh density is then tuned to reduce inaccuracy in the ndings.The periodic boundaries are then established along the vertical direction of the device axis.Following that, completely matched layers are typically placed alongside the PV axis.The program determines the distribution of normalized electric eld intensity within the semiconductor device in the simulation and predicts the amount of absorbed power and optimum shortcircuit current density value of the PV device while assuming 100% internal quantum efficiency (because in an optical simulation, the effect of recombination cannot be considered).
As noted earlier, the dimension of the active layer within a PV device holds a pivotal role in shaping the device's PCE.In light of this, endeavors have been undertaken to ne-tune the active layer thickness in various IOPV congurations, with the aim of elevating the PCE.Vincent et al. have illuminated this facet through an optical simulation exploration, where they spotlight the potential of a conventional PV structure comprised of P3HT:ICBA.Moreover, their ndings advocate for the augmentation of PCE in active-material-based IOPVs employing P3HT:ICBA by judiciously modulating the device's photon absorption capabilities. 59ater, the same group assessed the suitability of P3HT:ICBA active-material-based indoor OPVs for harvesting low-intensity LED light.They tuned the thickness of the device's active layer using FDTD simulations for different incident light luminance values.They also demonstrated that with an optimal construction, the device may reach maximum PCE.They attempted to develop a technique for improving the PV device architecture to maximize device efficiency using a combination of optical modeling and experimentation 56 (Fig. 10a).
Using the same method, the impact of active-layer thickness on the level of performance of several semiconductor-based IOPVs was also examined.Shin et al., for example, found that the rate of decrease in ideal short-circuits density value (thus, the PCE value) of a PPDT2FBT:PC 70 BM active-material-based OPVs with increasing active-layer thickness is very slow for indoor applications, whereas the opposite behavior was observed under the 1 sun condition.They have suggested that the effect of critical parasitic resistance on the performance level of an OPV can be varied by changing the illuminating agent 64 (Fig. 10b).
FDTD optical simulations have been used to optimize the thickness of additional layers, as well as various other characteristics of IOPVs, in addition to the thickness of the active layer.Recently, Lee et al. attempted to develop an extremely efficient and adaptable IOPVs device using a quasi-amorphous transparent electrode (ZnO/Ag/ZnO) and P3HT:ICBA active material.Using an FDTD optical simulation analysis, they adjusted thickness of several components of a mechanically stable electrode of an IOPV device.They achieved a higher PCE (12.1%) for the lighting of a 500 lx LED lamp using a mix of modeling and experimental investigation. 55TD optical simulation studies have also been utilized for optimizing various parameters of quaternary IOPV devices.Shin et al. successfully improved the photo-energy absorption ability of the active layer (PCDTBT:PTB7:PC 61 BM:PC 71 BM) of quaternary IOPV devices through the optimization of the weight ratio of various components of the quaternary mixture.They also studied the inuence of active-layer thickness on the device's optimal short-circuit current density while working under a 500 lx white LED bulb in order to nd the best active-layer thickness 65 (Fig. 10c and d).
Vincent et al. conducted a comprehensive optical simulation investigation on a PCDTBT:PTB7:PC 61 BM:PC 71 BM activematerial-based IOPV device to identify the exact function of the quaternary combination during device operation.They discovered that the thickness (active layer) dependent optimum short-circuit current density value of a quaternary IOPV may oscillate more.Furthermore, because to interference between incoming and reected (from the back electrode) light, the simulated electric eld intensity value had a very high sensitivity within its active to its thickness.They also determined that PCDTBT is the device's primary light absorber, while PTB7 functions as a cascade energy level and a supplemental light absorber during operation 60 (Fig. 11).
Through an in-depth review study, it becomes evident that achieving the utmost PCE from a PV device is intrinsically linked to the meticulous optimization of the respective layer thicknesses within its structure.In the realm of optimizing these dimensions, the parameter sweep strategy stands as a conventional practice within the Lumerical FDTD solutions soware.However, it has become apparent that a brute-force approach is oen suboptimal, particularly when aiming for an optimal outcome in varied scenarios.In response to this challenge, Vincent et al. embarked on an innovative pathway.They harnessed a genetic algorithm for their device simulation investigation, a method grounded in the principles of Darwinian evolution and natural selection.Notably, their exploration unveiled that this novel optimization methodology accelerates the optimization process and augments precision, in contrast to the traditional brute-force parameter sweep technique 62 (Fig. 12).
Kim et al. recently showed that, while precise balanced band gap estimations show tandem photovoltaics to be feasible for 1 sun conditions, single active layer-based photovoltaics can better collect the low-intensity emission spectra of white LED light sources.The current-matching constraint of a tandem photovoltaic structure coupled in series restricts the device's maximum J SC and V OC , and hence its performance for lowintensity light illumination. 58They used optical simulation to estimate different device performance characteristics.
In another study Kim and coworkers designed an indoor OPV having PTB7-Th:PC 70 BM active layer and low-acidic and cheaper polypyrrole:polystyrene sulfonate (PPY:PSS) as the hole transport layer (HTL), by optimizing active layer thickness and processing conditions (spin coating speed and doping concentration) of the HTL via optical simulations and experiments.The results show that the device having 100 nm thick active layer and a PPY:PSS-based HTL (PPY : PSS; weight ratio between PPY and PSS 1 : 2) coated at 5000 rpm can exhibit a record high PCE value (16.35%) during its operation under 1000 lx LED lamp.In comparison, a commercially available PEDOT:PSSbased OPV can achieve maximum 14.21% PCE under the same conditions. 101rom the literature survey, it has been observed that in most cases, varied device parameters of indoor PVs have been optimized via optical simulation studies, whereas the effects of generation rate, recombination rate, diffusion of charge carrier, and the collection procedure of electrons on the performance of the PV devices has not been explored.Therefore, electrical simulation studies can be a very good option to realize the effect of variation of various device parameters on the performance of an indoor PV device more precisely. 102Thus far, various electrical models such as effective medium model and the Monte Carlo model have been used to perform electrical stimulation of various PV structures.Recently, some researchers have tried to estimate the effect of the morphology of various layers, 103 domain size, 104 and weight ratio of donor and acceptor 104 on the charge transport mechanism of various organic solar cells using the Monte Carlo model.A device simulation investigation may be seen as a highly strong technique for improving the architecture of IOPV devices in this review study.Several attempts have been done over the last four years to improve different device characteristics of various IOPVs using optical simulation studies.Although the generation rate, recombination rate, charge carrier diffusion, and electron and hole collection procedure within the PV device all play important roles during device operation, understanding the effect of the aforementioned parameters on the performance level of an IOPV has not been attempted through electrical simulation studies.As a result, in the near future, a combination of experimental, optical, and electrical modeling investigations of IOPV devices may be done in order to build commercially useable, highly efficient, mechanically exible next-generation IOPV devices.

Commercial prospects of IOPVs
Various initiatives for the creation of IOPVs have been implemented throughout the previous decade.Unfortunately, the commercialization of IOPVs has not yet been achieved.A very high PCE (over 20% when illuminated by a 500 lx indoor light) and a greater output power density (30 mW cm −2 ) are not the only characteristics to consider when commercializing OPV devices.There are a number of other considerations that must be made.These issues will be addressed in this section.
First, the lifespan of the IOPVs is a critical consideration.IOPVs have the potential to replace traditional tiny batteries across numerous electrical devices networked inside an IoT network, reducing maintenance costs.To satisfy this requirement, IOPVs must exhibit exceptional environmental resilience, assuring device longevity of a decade or more while maintaining a minimum of 80% original efficiency towards the end of this span.Currently, the operating life of an IOPV is just around two years.As a result, further research is required to develop fundamentally stable constituent materials (including donor and acceptor components, hole transport and electron transport layers, and electrodes) adapted specifically for IOPVs, culminating in their successful commercial realization.
While the importance of stability problems may be reduced in indoor applications, it is worth noting that OPV devices continue to perform poorly when compared to their classic inorganic solar cell counterparts.The several elements impacting device stability, including photodegradation and thermal deterioration, must be given careful consideration.These complicated procedures place restrictions on the devices' long-term performance and dependability. 105or the commercialization of IOPVs, the large-scale deposition method is highly encouraged.In such a scenario, the spin coating technology, which is generally utilized, is not a good option.Some studies on IOPVs made with blade coating and lotdie coating, which are more suited to industrial operations, have been reported.Further research is needed on the optimization of various factors, such as solubility of the materials and boiling point of the solvents, during the coating of various layers of an IOPV through various large-area-coating technologies because those factors have a noticeable effect on the morphology, thickness uniformity, and packing of the constant materials of the lms.For developing a well-behaved IOPV, the aforementioned properties of various lms of the device should be controlled properly.
In addition, the production cost of the device should be minimized.In the near future, it is strongly recommended to develop well-behaved low-cost constituent materials as well as a practical, time-saving, and cost-effective large-area device manufacturing method.
Given the application purpose of IOPVs, the development of efficient, exible, and stretchable IOPV modules is a necessity.Along with exibility, the device should exhibit stable performance irrespective of the bending number.For example, Li et al. have recently designed a novel intrinsic anti-reection, high-transmission, and stretchable substrate was designed to construct highly efficient stretchable ITO-free (6k-PDMS/ PEDOT:PSS transparent substrate) IOPV. 106The stretchable substrate has showed a high diffuse transmittance of over 95% and a transmittance haze of 88%, which can be simply duplicated from the surface texture of commercial 3M abrasive papers.Owing to the high EQE and shunt resistance, the devices with the surface-textured ITO-free stretchable substrates has exhibited a high PCE of 20.5% compared to that of the rigid devices (20.8%) under indoor application.On the other hand, Kim and colleagues have recently reported indium zinc tin oxide bottom electrode-based exible IOPV with remarkably high mechanical stability. 107The OPV shows z69% of its initial PCE value aer 100 000 bending repetitions for 1000 lx LED illumination.From the review it has been observed that, few researchers have attempted the development of exible and stretchable IOPVs.Furthermore, the devices' PCE values are inferior to those of their rigid equivalents.As a result, extensive research in this eld is necessary.
An IoT network includes several wearable devices.Consequently, a biocompatible powering tool (i.e., IOPVs) for those devices is desirable.It will be highly useful to produce ecofriendly and biocompatible component materials for IOPVs.If IOPVs meet the aforementioned conditions, we anticipate they will achieve commercial-scale manufacturing in near future.
Besides the aforementioned issues, another important concern must be resolved.There is a basic difference between outdoor and indoor lighting conditions.Under outdoor (i.e., 1 sun) conditions, the light is incident directly onto the device, whereas indoors, diffused light (reected from surfaces such as walls and the surfaces of varied articles) illuminates PV devices.Therefore, during testing of indoor OPVs, the measuring unit must be customized accordingly. 67At present, there is no standard protocol for measuring OPVs under indoor lighting conditions.As accurate testing of a PV device is always needed for its commercialization, a standardized measurement system is essential.

Conclusions
In this systematic review study, it has been found that indoor light energy may be harvested and used to power different tiny and low-powered indoor electronic devices using IOPVs.IOPVs are energy harvesters with unique optoelectronic features and a broad range of applications.Only a few years ago, research into the development of OPVs for indoor applications began.Through the deployment of various optoelectronics methods, IOPVs have already reached above 30% PCE.This value can be further improved; theoretically, it has been calculated that an ideal OPV with an active layer having an energy band gap value within 1.90-2.20 eV can exhibit over 50% PCE under the illumination of FL lamps and LEDs. 16owever, to achieve this, several issues must be resolved.For example, depending on the light source, the optical energy band gap of photoactive materials must be modied.To decrease energy loss under low-intensity indoor lighting, sufficiently high V OC -generating active materials must be produced.Furthermore, the optimization of the OPV devices for low-intensity indoor light may differ from the optimization under 1 sun conditions.Although many ETLs have been developed for the enhancement of electron extraction ability of an indoor OPV, there are very few reports on the development of new HTLs for IOPVs for improving their hole extraction efficiency and lifespan.Further research is also needed on developing exible, large area, and semitransparent OPVs for their commercialization.Furthermore, currently there is no standardized measurement condition for IOPVs.Different research groups are using different illuminating agents, irradiance power intensity, and luminance value.This makes comparing and evaluating the experimental outcomes challenging.As a result, a consistent measuring procedure for characterizing OPVs under the irradiation of diverse indoor light sources is required.

Fig. 2
Fig. 2 Experimental setup for low irradiance measuring unit: (a) shorter distance between light source (CFL) and measuring unit, (b) longer distance (1.4 m) between light source (CFL) and measuring unit, and (c) schematic at standardized condition, variation of luminance value of incident light on different position of PV cell for both (d) short, and (e) long-distance between light source (CFL) and measuring unit, (f) relation between irradiance power intensity and luminance of different sources of indoor light; [reproduced with permission, 67 copyright 2020, IEEE].(g) Effect of the exposure time on illuminance measurement results repeated 20 times determined for a lighting apparatus (ALPHAX Co., Ltd Type AL-50FL): number of integrations was set to 5 (exposure time was set to 12.8 ms in the automatic mode), (h) current density fluctuation of c-Si PV (power generation area: 1.96 cm 2 ) caused by light blinking of a lighting apparatus (ALPHAX Co., Ltd Type AL-50FL); [reproduced with permission, 68 copyright 2018, The Electrochemical Society of Japan].

Fig. 5
Fig. 5 The chemical structures of different non-fullerene-acceptor materials utilized in indoor OPVs.

Fig. 6 J
Fig. 6 J-V characteristics of binary PCDTBT:PC 71 BM and ternary PCDTBT:PDTSTPD:PC 71 BM OPVs under (a) 300 lx FL lamp (2700 K) and (b) 300 lx LED illumination (6500 K); [reproduced with permission. 89Copyright 2018, The Royal Society of Chemistry].(c) Quaternary OPV device construction, (d) organic compound energy band levels in the BHJ and other layers, (e) BHJ absorbance with varied composition weight ratios, (f) experimentally determined J-V curves of quaternary OPVs with various composition weight ratios under 500 lx white LED illumination; [reproduced with permission. 65Copyright 2019, Elsevier].(g) ST Q-OPV schematic diagram and (h) energy level, based on two polymer donors, one fullerene acceptor, and one non-fullerene acceptor, (i) J-V curve of the ST Q-OPV under 1000 lx LED illumination; [reproduced with permission. 90Copyright 2019, Elsevier].

Fig. 7
Fig. 7 Chemical structures of several materials used as indoor OPV interlayers (HTL or ETL).

Fig. 9
Fig. 9 (a) Architecture of an indoor OPV based on PANI:PSS HTL and P3HT:ICBA active layer, (b) J-V characteristics of the OPV operating under 500 lx and 1000 lx LED, (c) variation of normalized PCE of OPVs (PEDOT:PSS and PANI:PSS HTL-based) with their lifespan; [reproduced with permission. 44Copyright 2020, Elsevier].(d) Variation of pH value of PANI:PSS as per its concentration of PSS, (e) representative J-V characteristics of an OPV operating under the illumination of 500 lx LED, (f) variation of PCE value of OPVs (operating under 500 lx LED and 1 sun condition) with the doping concentration of its HTL; [reproduced with permission. 46Copyright 2020, Elsevier].(g) Architecture of an indoor OPV with WO 3 HTL and P3HT:ICBA active layer, (h) comparison of work function value of ITO, WO 3 and PEDOT:PSS, (i) representative J-V characteristics of OPVs (having different HTLs) operating under the illumination of 1000 lx LED; [reproduced with permission. 48Copyright 2020, Elsevier].

Fig. 11 (
Fig. 11 (a) Number of photons absorbed (directly related to the J SC,ideal ) in quaternary and single BHJ photovoltaic cells illuminated with LEDs, (b) number of photons absorbed in quaternary and single BHJ photovoltaic cells illuminated with AM1.5 G, (c) simulated electric field intensity distribution inside the solar structure.The active layer thickness was 230 nm, which resulted in peak absorption under 500 lx indoor white LED illuminations, (d) absorption of quaternary and single BHJ active layers at 230 nm thickness; [reproduced with permission. 60Copyright 2019, MDPI].

Fig. 12
Fig. 12 Results of the Brute-force method: (a) single ZnO layer optimization, (b) single MoOx layer optimization, (c) multiple ZnO and MoOx layers optimization, (d) 2D data representation of (c) using labels pointing to the ZnO and MoOx layer thickness combinations for ease of calculation [reproduced with permission. 62Copyright 2019, MDPI].

Table 2
Summary of photovoltaic properties of previously reported non-fullerene-based indoor OPVs (binary)

Table 3
Summary of photovoltaic properties of previously reported multiple donor-acceptor-based OPVs