Continuous flow strategies for using fluorinated greenhouse gases in fluoroalkylations

Large quantities of fluorinated gases are generated as intermediates or byproducts from fluorinated polymer production annually, and they are eﬀective ozone depleting substances or greenhouse gases. On the other hand, the incorporation of fluoroalkyl groups into drug molecules or bioactive compounds has been shown to enhance biological properties such as the bioavailability, binding selectivity, and metabolic stability. Extraction of fluoroalkyl sources, including trifluoromethyl and difluoromethyl groups, from the fluorinated gases is highly desirable, yet challenging under regular batch reaction conditions. Flow chemistry is an emerging and promising technique to address long-standing challenges in gas– liquid batch reactions such as insufficient interfacial contact and scalability issues. In this review, we highlight recent advances in continuous flow strategies toward enabling the use of fluorinated greenhouse gases in organic synthesis.


Introduction
The highly electronegative fluorine atoms pose a strong electron-withdrawing effect and hydrophobic properties when they are bound to a single carbon atom, rendering them an inevitable part in modern pharmaceutical, agricultural, and materials science. 1 In particular, fluoroalkyl groups including trifluoromethyl (CF 3 ) or difluoromethyl groups (CF 2 H) are wellaccepted by the medicinal chemistry community as important structural motifs in bioactive compounds.3][4] The strategy has garnered considerable attention and many therapeutic drugs and agrochemicals bear at least one or more fluoroalkyl groups (Fig. 1).
Recent studies have shown that the difluoromethyl group has a character of lipophilic hydrogen bond donor and could serve as a bioisostere for thiols, alcohols and amines. 5,6he preparation of the fluoroalkylated compounds were typically achieved by using precursor reagents which deliver the fluoroalkyl groups though a variety of reaction mechanisms, such as photoredox, transition metal-catalyzed, nucleophilic, or electrophilic reactions.][9][10][11] Nonetheless, many of the fluoroalkylation reagents are expensive, potentially toxic, have a poor atom economy or require multiple synthetic steps for preparation.In this regard, fluorinated greenhouse gases such as fluoroform (CF 3 H), iodotrifluoromethane (CF 3 I) or chlorodifluoromethane (ClCF 2 H) are undeniably more attractive candidates for highly atom-efficient fluoroalkylations.Harvesting the trifluoromethyl and difluoromethyl sources from these gases for synthesis of APIs (active pharmaceutical ingredients) has the additional benefit of the simultaneous elimination of greenhouse gases.While indeed they have been demonstrated for such purposes, why are they not as widely used as the other commonly employed reagents such as Ruppert-Prakash reagent (TMSCF 3 )?This tutorial review aims to present the limitations of using the aforementioned fluorinated greenhouse gases in regular batch-mode organic synthesis as well as the continuous flow strategies to solve these problems.We will highlight recent examples, the batch-to-flow transition of the chemistries, and specific techniques used, and provide insights into flow-enabled reactions using the fluorinated gases.

Limitations of gas-liquid reactions in batch
Large quantities of fluorinated gases are generated as intermediates or byproducts from fluorinated polymer production.For example, fluoroform is a side product from the production of chlorodifluoromethane, which is a refrigerant and an intermediate from PTFE (polytetrafluoroethylene) manufacturing.These fluorinated byproducts are effective ozone depleting substances and/or greenhouse gases, and it is desirable to use them productively.Unfortunately, their use under regular batch chemistry conditions is highly restricted or inefficient.Batch chemistry (or batch synthesis) refers to a series of operations carried out in an organic synthesis to produce chemicals on a batch-by-batch basis, including reaction, purification, and analytical processes.In many chemical laboratories, batch chemistry is conducted using conventional synthetic glassware such as round bottom flasks.In fact, a multitude of the challenges is associated with the solubility of the gases in solution and their handling using conventional glassware.To utilize fluorinated gases in batches, it is common practice to prepare a stock solution by saturating the compound in an organic solvent through continuous bubbling for several hours (Fig. 2A). 12owever, the bubbled greenhouse gas could escape from the solvent and re-enter the atmosphere over time, thus rendering a limited shelf-life.Several solvents are commonly employed for this purpose (dimethylformamide (DMF), acetonitrile, 1,4dioxane), but the reaction medium would be limited, and preparation of multiple stock solutions is laborious.Condensing the gas inside the reaction flask at a low temperature (e.g.À85 1C) is another feasible way, but it demands techniques and subsequent expansion of the gas raises safety concerns.Bubbling the gas directly into the mixture during the course of reaction would lengthen the reaction time and the gas could escape into the system headspace or atmosphere, which is undesirable when using a greenhouse gas.Although conducting the reaction in a closed system (e.g.Schlenk flask, autoclave) could limit the loss of the gas (Fig. 2B and C), the gas-liquid interfacial contact is still insufficient and results in poor mixing efficiency.Moreover, it would be very challenging to establish the correct stoichiometry between the gaseous reagent and substrates due to a number of factors, such as loss of gas, slight volume difference between pieces of glassware, solubility of gases in reaction solvent or human errors during reaction setup.Notably, batch gas-liquid reactions also experience unique challenges when being scaled up to production quantities.For example, addressing safety risks includes quenching of toxic/ greenhouse gases, re-optimization of reaction conditions or redesign of reactors.In the past few years, we have observed that there is an emerging trend of using flow chemistry techniques to address these problems.While several review articles have discussed the use of gases in continuous flow synthesis, [13][14][15][16] fluorinated greenhouse gases have not been covered.

Advantages of continuous flow chemistry
For about two centuries, batch chemistry has been the mainstream way of carrying out organic synthesis in many chemical laboratories in both academia and industry.Despite the advancement of analytical and purification instruments, multistep reactions and purifications are still time-and laborintensive.Flow chemistry is a powerful synthetic tool which advances chemical synthesis by enhancing productivity while reducing costs and transforming production of fine chemicals.][15][16] Fundamentally, flow synthesis is achieved by pumping the solutions of reactants and reagents through microreactors where the chemical reaction is exposed to different conditions such as heating, cooling, or microwave, acoustic or photo irradiation, and products are continuously eluted (Fig. 3).Heat transfer and mass transfer (mixing) are greatly improved as the reaction mixtures are driven through the small channels of microreactors, where the surface area to volume ratio is increased and reaction rates can be raised if the rate-limiting factor of the reaction is mixing or temperature.Temperature of the solutions can be changed extremely rapidly and precisely controlled.Toxic, unstable, and pyrophoric compounds can be generated on demand or handled in very small amounts to mitigate safety hazards, while immediate consumption of these chemicals in flow is highly desirable for reactions dealing with short-lived species.Mixing units and separation modules allow for the streamlining of multiple synthetic steps, safe quenching of toxic chemicals, and in-line purification.The term ''in-line'' in flow chemistry refers to the flowing stream being manipulated or analyzed without exiting the continuous flow system.Flow systems also have a small footprint, and it is relatively easy to scale up reactions in flow than in batch.Scaling up flow reactions is usually achieved by increasing flow rates, reactor volumes or product collection time.
Importantly, gas-liquid reactions benefit significantly from being transferred to flow and the use of gases in flow is generally easier and more efficient.The lack of system headspace in Fig. 3 Common flow equipment used in a continuous flow system.Fig. 2 Common equipment used in gas-liquid biphasic reactions under batch conditions: (A) A CF 3 I-saturated DMF stock solution in a Schlenk graduated cylinder. 12Reprinted with permission from ref. 12, Copyright microreactors and increased interfacial contact area would be highly advantageous to biphasic gas-liquid reactions and could permit previously improbable reaction conditions.The stoichiometry of reagents is critical to many organic reactions, and the introduction of gases to a flow system can be precisely controlled by a mass flow controller (MFC).While there is no head space in a flow reactor, the gases cannot escape the system.Pressurization of flow systems is relatively easy and can be achieved using a back pressure regulator (BPR).The application of high pressure can assist gas dissolution in solutions and solvents can also be heated beyond their boiling points without evaporation.For example, the boiling point of water can reach 203 1C under a pressure of 250 psi.

Flow equipment
A very basic flow setup includes a pump and a microreactor, but depending on the reaction conditions or requirements, a number of units or equipment could be integrated for different purposes.HPLC systems, peristaltic and syringe pumps are used to deliver solutions into microreactors such as coil, chip or packed-bed reactors (Fig. 3).Plastic, glass or stainless steel syringes can be used and mounted onto the syringe pumps according to the reaction pressure and properties of the chemicals.Coil reactors can be constructed in a modular fashion using PFA (perfluoroalkoxy alkane), PTFE (polytetrafluoroethylene) or stainless-steel tubing, whereas the inner diameter ranges from 0.02 to 0.06 inches for lab scale.Stainless-steel tubing and syringe are recommended for high-pressure and/or high-temperature reactions.Smaller inner diameter generally affords better mixing but is also more prone to clogging by solids.It is noteworthy that clogging is one of the most encountered problems in continuous flow systems.Possible solutions include increasing flow rates and/or inner diameter of channel, diluting the mixture, sonication, as well as increasing temperature or adding a co-solvent to increase the solubility.The counterion also plays an important role.For example, in the case of forming insoluble NEt 3 ÁHCl in organic solvent, tributylamine could be used to increase the solubility.For palladium chemistry, increasing ligand loading might prevent the formation of palladium black precipitate.Packed-bed reactors are columns which can be filled with a heterogeneous catalyst (e.g.Pd on carbon), solid reagents, solid-supported reagents, or chemically inert beads for continuous mixing of a biphasic mixture.However, it should be noted that the use of solid-supported reagents and purification materials can offset the continuity of a flow system due to the eventual replacement of consumable materials.In comparison to the reaction time in batch synthesis, the residence time (t R ) in flow chemistry is the time reaction mixture spent in the reactor and is dictated by flow rates and reactor volumes (eqn (1)).Y-, T-, crossmixers and unions are used to join separate streams and connect individual reactors.Check valves enable one-way flow to prevent back-flow of solution and are typically useful in a high-pressure flow reaction.A back pressure regulator (BPR) maintains a constant pressure of a flow system by controlling the area of flow path and is typically placed at the end of the flow system.The liquid fluid has to reach a predefined pressure to pass through the BPR, a pressure of 0-290 psi is usually used in lab-scale reactions depending on the reaction conditions.If insoluble solids aggregate inside the BPR, one possible solution is to introduce a stream of co-solvent to the flow prior to entering the BPR, and the solvent system of the reaction will not be affected.For in-line purifications, a separator can provide continuous separation of immiscible phases, including gas-liquid or liquid-liquid phases, by the differences in the wetting properties of fluids onto a porous membrane.residence time ¼ reactor volume flow rate : For gas-liquid reactions, a mass flow controller (MFC) can be used and is a programmed device which introduces gaseous compounds to the flow system in an accurate and reproducible fashion (Fig. 4A).The flow rate is measured via the heat transfer between the gas and the thermal sensor in the MFC, and a control valve establishes the flow according to the set flow rate.MFCs can be calibrated to control specific types of gas at a particular range of flow rates.Micro-metering valves are costeffective alternatives and can also be used to control the size and flow rate of gas bubbles (Fig. 4A), but they are difficult to adjust and are not as accurate as the MFCs.When the separate streams of gas and liquid are joined and driven through a microfluidic channel, segmented flow (or Taylor flow) could be generated (Fig. 5). 17The Taylor recirculation pattern facilitates internal and interfacial mixing while a thin liquid film surrounds the gas bubble and further promotes the saturation.Appropriate pressurization of flow systems using a BPR could eliminate flow segments and keep gases in the solution phase.Alternatively, another widely used approach for the gas-liquid flow chemistry is the tube-in-tube reactor developed by Ley and co-workers (Fig. 4B). 13A Teflon AF-2400 membrane tubing is inserted into a large PTFE tube and connected by T-mixers.Pressurized gases occupy the reactor and diffuse monodirectionally into the inner tube through the membrane and saturate the solution with the gas.A reverse design could be adopted, whereas the gases pass through the inner tubing and the outer solution stream could be exposed to different temperatures and irradiation conditions.

Fluoroform
Fluoroform (CF 3 H, as known as Freon 23 or HCFC-23) is produced in large quantities each year as an industrial byproduct in the production of chlorodifluoromethane, an intermediate towards the PTFE (polytetrafluoroethylene) product, such as DuPont's Telfon s .CF 3 H is a colorless gas (b.p. = À82 1C) at room temperature and atmospheric pressure.Although CF 3 H is not toxic nor ozone depleting, the potent greenhouse gas is 14 800 times more powerful than carbon dioxide in the atmosphere in terms of GWP (Global Warming Potential) over a 100-year period. 18Under the regulation of the Kyoto Protocol, the release of fluoroform into the atmosphere is prohibited and it has to be collected for incineration or further This journal is © The Royal Society of Chemistry 2021 commodity purposes.Fluoroform is arguably an ideal trifluoromethyl source because it is inexpensive, atom-economical, and readily available, but its chemical inertness is difficult to overcome.The generation of the CF 3 anion by proton abstraction of fluoroform is potentially the most straightforward way to harvest the trifluoromethyl source.However, activating CF 3 H is challenging because the C-H bond of CF 3 H is weakly acidic with a pK a of 25-28. 19Moreover, the resulting CF 3 anion is highly unstable and undergoes a-elimination rapidly to give singlet difluorocarbene and fluoride ion, but this situation could be taken as an advantage for difluoromethylation reactions in certain cases.Considerable progress in the activation of fluoroform under batch conditions was made in the past decades from the 1990s, and they were reviewed recently. 20Here, we will focus on the examples that were adopted in continuous flow to show the transition from batch to flow and their improvements in different aspects including procedures and reaction efficiency.

Trifluoromethylations
In 2012, Prakash and co-workers made a ground-breaking contribution in the deprotonation of fluoroform and reported the direct nucleophilic trifluoromethylation of carbon, silicon, boron, and sulfur electrophiles (Fig. 6). 21They found KHMDS (potassium hexamethyldisilazide, pK a = 26) as an effective base to deprotonate fluoroform at very low temperatures (À40 to À85 1C) and the resulting CF 3 anion was proposed to immediately react with the electrophiles.Using K + as the cation of the base was found to be important, while the reactions using NaHMDS and LHMDS failed to give any desired products.Silyl chlorides (R 3 SiCl) were converted to trifluoromethylated silanes in toluene (42-44% yield) and non-enolizable ketones were trifluoromethylated in diethyl ether (38-78% yield).Aldehydes were also applicable substrates when THF and KOt-Bu were used.Trifluoromethylated trifluoroborate salt (CF 3 BF 3 K) and triflic acid (CF 3 SO 2 H) were prepared from trialkyl borate (B(OR) 3 ) and sulfur (S 8 ) in good to excellent yields, respectively.In general, fluoroform (1 equiv.) was bubbled into the reaction  mixture for minutes to hours, depending on the substrates, before the addition of KHMDS and stirred at room temperature for 10 to 16 hours.Although the fluoroform could be retained in the solution at low temperatures such as À78 1C, it is anticipated that the reaction might encounter scalability problems as a temperature gradient would form across the mixture, in which it could affect the deprotonation process or fail to hold the fluoroform at a larger scale.
The discharge of fluoroform into the atmosphere during or after the course of reaction is undesirable and regulated.Ley and co-workers showed that the use of in-line NMR (nuclear magnetic resonance) and FT-IR (Fourier-transform infrared spectroscopy) monitoring could enable safe and efficient consumption of fluoroform in nucleophilic trifluoromethylations (Fig. 7). 22Fluoroform was introduced into a tube-in-tube reactor (inner tubing: Teflon AF-2400; outer tubing: PTFE) at 44 psi and THF was pumped into the inner tube of the reactor.The fluoroform-saturated THF was then mixed with separate streams of KHMDS (1 M in THF) and ketone substrate (1 M in THF) at a cross-mixer and the combined mixture was directed into a PTFE coil reactor.It is noteworthy that the mixing zone and reactor were both maintained at À20 1C to suppress fluoride elimination of the CF 3 anion.The FT-IR installed after the reactor was used to monitor whether the steady state of the flow system is reached using PhCF 3 as the internal standard.The mixture was then flowed through an in-line benchtop NMR where 19 F NMR spectra were recorded.In-line NMR analysis determined the concentration of fluoroform dissolved in the solution (0.738 M) and was used to optimize the consumption of fluoroform.A BPR (75 psi) was placed at the end of the system to prevent the evaporation of fluoroform and to ensure a homogeneous mixture.Complete consumption of fluoroform was achieved in flow while the efficiency is much higher than the analogous batch method, 21 in terms of control of fluoroform dosing and production rate (4.6 vs. 0.225 mmol h À1 ).DMF and KOt-Bu were used as the solvent and the base for the flow reaction of aldehydes to provide trifluoromethylated alcohols in 75-97% yield within 27 minutes (Fig. 7).Interestingly, the authors have observed by in-line NMR analysis that TMSprotected alcohol was formed first before deprotection to give the trifluoromethylated products, but the theoretical side product TMSF was not observed on 19 F NMR spectra.The authors then integrated a silylation module between the in-line FT-IR and NMR for derivatization of alcohols (Fig. 8).A fourth stream of TMSCl (0.3 M in THF) was mixed with the solutions at the output of FT-IR and the resulting solution was directed to another PTFE coil to yield O-trimethylsilyl fluorinated ethers in good to excellent yields within a total t R of 36.6 minutes.Using system illustrated in Fig. 7, triethylsilyl chloride (TESCl) was also successfully trifluoromethylated.The flow conditions  for synthesis of TESCF 3 was re-optimized with real-time monitoring of the reaction mixture and it was found that a longer residence time (57 min) and lower temperature (À40 1C) were needed.Complete consumption of fluoroform was achieved for both cases.
Recently, the Shibata group reported a rapid trifluoromethylation of aldehydes, ketones, and N-sulfinylmines using fluoroform in continuous flow. 23As shown in Fig. 9, fluoroform was accurately delivered at atmospheric pressure into the flow system by a mass flow controller and mixed with a stream containing the ketone and KOt-Bu at a Y-mixer.Although an excess amount of fluoroform was used (1.7 equiv.), the residence time for the reaction mixture in the stainless-steel coil reactor was only 0.5 seconds.Notably, the ultra-short residence time enabled the reaction to proceed at room temperature and give trifluoromethylated products in moderate to excellent yields (35-98% yield).Similarly, aldehydes were also trifluoromethylated in 1.3 seconds using KOt-bu as base while flow reactions of chalcones and N-sulfinylimines completed within 0.5 seconds using Prakash conditions (KHMDS, toluene).In a comparison, the Shibata flow method provided the trifluoromethylated alcohols with the highest production rate (35.3 mmol h À1 ).The Shibata group further evaluated the potential of their method for the synthesis of Efavirenz, a medication to treat human immunodeficiency virus (HIV) infection.It should be noted that using the Prakash conditions (KHMDS/toluene) at sub-zero temperatures in continuous flow could lead to clogging because of the precipitation of KHMDS.In this case, a change of solvent to THF could solve the problem.
As trifluoromethyl anion is highly unstable and has to be generated under low temperature to avoid a-elimination, its strict deprotonation conditions and highly nucleophilic nature might limit the substrate scope, choice of reaction solvent, as well as compatibility with other reagents.An alternative is metalation of fluoroform to generate stable trifluoromethyl organometallic species that give wider access to a range of reactions, substrates, and electrophiles such as aryl halides.5][26] The authors have found that the reaction of CuCl with KOt-Bu (2 equiv.) in DMF quantitatively afforded an ate complex [K(DMF) n ][Cu(Ot-Bu) 2 ], which readily cuprates fluoroform at room temperature to form complex A in 97% yield.However, complex A would slowly decompose due to a-fluoride elimination caused by the electrophilic attack of K + cations on fluorine atoms of the trifluoromethyl group, while the tert-butoxide could cause competitive tert-butoxylation with the desired trifluoromethylation. 26 Et 3 N(HF) 3 , as known as TREAT-HF, was added to the mixture to remove the K + cation and tert-butoxide in the form of KF and tert-butanol to furnish a ''ligandless'' CuCF 3 reagent.The CuCF 3 solution is stable for a few days at room temperature and for months at À30 1C.The trifluoromethylation reagent Fig. 8 Telescoped system for synthesis of O-trimethylsilyl fluorinated ethers. 22g. 9 Rapid continuous flow trifluoromethylation using fluoroform gas. 23][26] was highly reactive toward a wide range of substrates including (hetero)aryl iodides, aryl Pd(II) halide species, N-heterocyclic carbene, and a-haloketones (Fig. 10).
Two years after the first report of fluoroform cupration under batch conditions, the same group established a continuous flow process to scale up the synthesis of the CuCF 3 reagent. 27In the original report, the cupration step with fluoroform was performed in a Fisher-Porter tube equipped with a pressure gauge, where several fluoroform gas refilling cycles have to be carried out at pressures of up to 50 psi.The cupration step was transferred to flow and the flow setup is depicted in Fig. 11A.The cuprating reagent [K(DMF) n ][Cu(Ot-Bu) 2 ] was prepared separately in DMF and delivered into the flow system by a syringe pump.1.5 equivalents of fluoroform was accurately introduced by an MFC to a Y-mixer and mixed with the cuprating reagent.The resulting gas-liquid segmented flow passed through a PTFE coil at room temperature and atmospheric pressure for a t R of 9.3 minutes and was collected in a vessel under argon atmosphere.The stabilizing step was achieved by pumping TREAT-HF solution to the crude mixture in the collecting vessel under continuous stirring and 94% yield of CuCF 3 was obtained.Attempts were made to mix the crude mixture with TREAT-HF in a T-mixer but the precipitation of KF eventually clogged the system.Since CuCF 3 is only stable for a few days at room temperature and is air-sensitive, the authors examined the possibility of an in-line trifluoromethylation to consume the trifluoromethylation reagent immediately.Four configurations were tested for trifluoromethylations of a-bromoketone, aryl iodide, bromide, and boronic acids.A representative example is illustrated in Fig. 11B.A peristaltic pump continuously transferred the resultant reagent solution from the original flow setup to a glass reactor where the substrate and additional TREAT-HF solution were continuously introduced.[26]

Difluoromethylations
Fluoroform could be utilized as a source of the CF 2 H moiety, which has been increasingly present in important pharmaceutical compounds.As previously mentioned, trifluoromethyl anion could rapidly undergo a-elimination of fluoride ions to afford difluorocarbenes.Commercial trifluoromethylation reagents such as TMSCF 3 have been shown to generate difluorocarbenes for difluoromethylations, 28 difluorocyclopropanations with alkenes, 29 and even in situ dimerization to form tetrafluoroethylene gas for tetrafluoroethylation. 30In a recent report, Thomoson and Dolbier demonstrated the first use of fluoroform gas in the direct difluoromethylation of phenols and thiophenols (Fig. 12). 31With continuous bubbling of excess fluoroform gas (8 to 14.2 equiv.)into a mixture of substrate and KOH for 2 to 4 hours, aryl and heteroaryl products were obtained in goodto-excellent yields.Their proposed mechanism involved a nucleophilic attack of the substrate anion to the short-lived electrophilic singlet difluorocarbene generated from fluoroform.When the reaction was carried out using potassium metal as the base and in the presence of D 2 O, a mixture of deuterated and regular products was provided, indicating that an ArOCF 2 À intermediate existed and was partly quenched by D 2 O.
In addition to the difluorocarbene chemistry, Mikami has proposed, in his difluoromethylation of enolates and nitriles, 32,33 lithium-mediated pathways based on their observations and DFT calculations.In the case of enolates (Fig. 13), 32 two equivalents of LHMDS (lithium hexamethyldisilazide) led to the aggregation of the lithium enolate homodimer B and the lithium ion was postulated to facilitate a S N 2-type C-F activation of fluoroform through Li-F interaction.Carbonyl compounds including ketone, ester, malonate, lactone and lactam were successfully difluoromethylated.For the a-difluoromethylation of aliphatic nitriles (Fig. 14), 33 trifluoromethyl lithium and lithium ketene imine were formed in the presence of n-butyl lithium while Li-F interactions were proposed in the transition state C. Removal of lithium fluoride yields the difluoromethyl lithium species D which then abstracts a proton from a fluoroform molecule to give the difluoromethylated product.
Fig. 11 (A) Continuous flow system for preparation of CuCF 3 using fluoroform gas.(B) Telescoped system for trifluoromethylation of a-bromoketone. 27g. 12 Difluoromethylation of phenols and thiophenols using fluoroform. 31n 2017, Kappe and co-workers demonstrated the versatility of flow chemistry by 3D-printing a stainless-steel reactor to carry out a continuous flow difluoromethylation of diphenylacetonitrile using fluoroform (Fig. 15). 34The team first designed the reactor model in silico, and tested the hypothetical 3D model using computational fluid dynamics (CDF) simulations to optimize the mixing geometry.The reactor was then printed using a technique called Selective Laser Melting (SLM), in which the metal slices are printed layer-by-layer via fusion of the applied metal powder.The SLM process was shown to reliably reproduce channels of as narrow as 0.6 mm diameter from their 3D model.The Mikami conditions were adopted in this continuous flow difluoromethylation of nitriles (Fig. 15).The substrate and n-BuLi were first mixed for a residence time of about 50 seconds and the resulting mixture was combined with the fluoroform gas introduced by an MFC.The zig-zag nature of the channels could mixing by stretching and folding of the flowing stream. 35A cryostat-cooled ethanol solution of À65 1C flowed through the inner tube and the pressure of the system was regulated at 5 bar by a BPR.The authors attempted the same reaction conditions with Teflon tubing and confirmed that the gaseous reagent completely dissolved in the liquid phase.A stream of MeOH quenched the n-BuLi prior to product collection and the difluoromethylated nitrile product was synthesized in 81% yield in less than 2 minutes.Compared to Mikami's method, Kappe's system is fully continuous, safer, easier to operate, and has a high productivity (4.8 vs. 19.5 mmol h À1 ).Instead of a Li-mediated mechanism, the Kappe group proposed that difluorocarbenes were generated and reacted with the substrate anions.
The same group also reported direct difluoromethylation on a-sp 3 -carbon of esters and malonates using the fluoroform gas in continuous flow. 36Mikami's reaction conditions for a-difluoromethylation of carbonyl compounds (LHMDS, THF) were found to be promising in Kappe's flow protocol during optimization studies.The first PFA reactor coil in the continuous flow system (Fig. 16) was employed to deprotonate the Fig. 13 Direct difluoromethylation of lithium enolate using fluoroform. 32g. 14 a-Difluoromethylation of nitriles using fluoroform. 33g. 15 A-3D-printed flow reactor for difluoromethylation of diphenylacetonitrile using fluoroform. 34Reprinted with permission from ref. 34,  Copyright 2017 The Royal Society of Chemistry.Fig. 16 Continuous flow difluoromethylation of a-sp 3 -carbon centers using fluoroform. 36ubstrate at À30 1C for a residence time of 4 minutes.Fluoroform (3 equiv.) was introduced into the system by an MFC and the second coil performed the generation of difluorocarbenes.The authors noted that a pressure of about 5 bar (72.5 psi) and temperatures below 25 C could lead to complete dissolution of fluoroform gas, but the combination of 12 bar (174 psi) pressure and À15 1C at the second reactor coil provided the best conversion and selectivity.excess use of fluoroform was to prevent pressure fluctuation due to the accumulation of inorganic solids, mainly LiF, inside the BPR.After a roomtemperature reaction in the third coil, the desired products were obtained in mostly excellent yields, except for substrates with a sterically hindered phenyl ring at the a-carbon.Notably, the flow difluoromethylation has a significantly shorter reaction time than Mikami's batch protocol as shown by product E (20 min.vs. 20 h). 32,36Since a-difluoromethyl amino acids are potent inhibitors of their corresponding a-amino acid decarboxylases, the a-difluoromethylation of N-benzylideneprotected amino acid methyl esters was also demonstrated and excellent conversions (495%) were observed.The crude mixtures were then subjected to heating with 6 N HCl at 150 1C in a microwave batch autoclave for 45 minutes to give the unprotected a-CF 2 H amino acids in 76-87% yield.
In 2018, the Kappe group built on the success of their flow synthesis of a-difluoromethyl-amino acids and developed a scalable continuous flow system for synthesis of D,L-a-difluoro- methylornithine (eflornithine) from fluoroform (Fig. 17). 37flornithine is used in treatments of bacterial and parasitic infections and has potential anti-cancer activity as well.The previously encountered accumulation of inorganic solids inside the BPR was solved by using a BPR with a wider channel width and smaller dead volume, allowing a smooth flow and the amount of fluoroform used to decrease.A borosilicate static glass mixer plate replaced the second reactor in the previous system (Fig. 16) to further improve mixing while an acidic hydrolysis module was established and coupled to the system.Notably, the PFA tube used (1/8 in.o.d.; 0.8 mm i.d.) for the deprotection process was carefully evaluated to ensure it withstands the high temperature and high pressure applied.Stainless-steel reactor was usually used for high-temperature processes, but was not preferred here due to the corrosion by HCl.After a total residence time of about 23 minutes, ornithine methyl ester F was difluoromethylated and deprotected to give eflornithine hydrochloride monohydrate in 86% isolated yield (19.5 g, 24 mmol h À1 ).Moreover, only 1.05 equiv. of fluoroform was used and it was fully consumed as determined by 19 F NMR analysis.

Trifluoroiodomethane
The odorless and colorless trifluoroiodomethane gas (CF 3 I, b.p. = À22.5 1C) is an attractive source of the trifluoromethyl fragment due to its low acute inhalation toxicity and availability.It is mainly used as a fire suppression flooding agent and is potentially a very effective greenhouse gas due to the absorption by C-F bonds in the atmospheric window.In the past decade, a vast number of photochemical methods have been developed as a means to release the CF 3 radical from CF 3 I.
The pioneering studies by the MacMillan group have allowed for an uptake in usage of CF 3 I in the synthesis of small molecules.In the 2000s, they have demonstrated the use of a unique combination of enamine and organometallic photoredox catalysis to activate the relatively inert CF 3 I (Fig. 18). 38F 3 radicals were produced and subsequently used in the synthesis of enatiotopically enriched a-trifluoromethyl aldehydes.Using (2R,5S)-2-t-butyl-3,5-dimethylimidazolidin-4-one TFA in 20 mol% as the chiral amine catalyst, Ir(ppy) 2 (dtb-bpy)PF 6 as the photocatalyst, and 2,6-lutidine as an ancillary base, a variety of aldehydes could react with CF 3 I to produce the a-trifluoromethylated aldehydes with high enantiopurity (Fig. 18).In their protocol, the CF 3 I (8.1 equiv.) was condensed in the reaction Fig. 17 Streamlined system for continuous flow synthesis of eflornithine from fluoroform. 37g. 18 Enantioselective a-trifluoromethylation of aldehyde using trifluoroiodomethane. 38 medium using a cold finger and a needle.Reactions required a temperature of À20 1C to retain the enantioselectivity.These conditions also allowed for the substitution of CF 3 I with an array of other fluorinated alkyl iodides.
For the proposed mechanism in Fig. 18, the excited iridium catalyst removes an electron from excess imidazolidinone and transfers it to the CF 3 I via a single electron transfer (SET) mechanism to generate the trifluoromethyl radical.This radical species then reacts with the enamine formed from the condensation of the imidazolidinone and the aldehyde.Chirality is induced here by the tert-butyl and methyl substituents of the imidazolidinone.The sterically hindering tert-butyl group will direct the alkene moiety away from itself and the methyl group selectively blocks radical addition to the Re face of the molecule, promoting Si facial selectivity.The resulting radical species is then converted into an iminium ion by the photocatalyst to perpetuate the photoredox cycle.The iminium ion is converted into the product aldehyde by hydrolysis.
A more general method was later developed by MacMillan and co-workers to use silyl enol ethers in the synthesis of racemic a-trifluoromethyl ketones (Fig. 19). 39This methodology was extended to esters and amides as well, without the need for a photocatalyst.
The Sanford group has built on MacMillan's work to utilize CF 3 I in the synthesis of aryl trifluoromethane products (Fig. 20). 12rifluoromethylated arenes are a common substructure of many medicinally relevant compounds.Sandford and co-workers demonstrated the trifluoromethylation of aryl boronic acids with CF 3 I gas via the merger of photoredox and copper catalysis.Aryl-CF 3 cross-coupling is accomplished by reacting aryl boronic acids with CF 3 I, using 20 mol% copper(I)acetate and 1 mol% Ru(bpy) 3 Cl 2 Á6H 2 O catalysts under irradiation of two 26W fluorescent lightbulbs.Stock solutions of CF 3 I (0.25 M) were prepared by bubbling the gas into DMF (Fig. 2A).A variety of (hetero)aryl boronic acids could be accommodated with electron withdrawing and electron donating substituents.Yields suffered when sterically hindered boronic acid substrates were used and low amounts of aryl iodide side products were occasionally observed.
A proposed mechanism (Fig. 20) suggests that photoexcited Ru(bpy) 3 Cl 2 Á6H 2 O oxidizes the copper(I) catalyst to copper(II) and transfers that electron to CF 3 I to generate the trifluoromethyl radical.The radical species can then combine with the copper catalyst to generate a copper(III) intermediate which undergoes transmetalation with the boronic acid substrate and subsequent reductive elimination to form the C-C bond in the product, followed by a regeneration of the copper(I) catalyst.
Further advancements that improve the accessibility of CF 3 I gas have been made.Ritter and co-workers have developed stable stock solutions of CF 3 I in tetramethylguanidine (TMG) and dimethyl sulfoxide (DMSO). 40By taking advantage of halogen bonding, CF 3 I can be bubbled into solution to make 1 : 1 or 1 : 2 adducts with TMG and DMSO respectively.These liquid reagents are comparatively easier to handle, measure and reliably maintain the concentration of CF 3 I over a period of at least two months when stored at 0 1C.These reagents are useful in a variety of trifluoromethylation reactions as demonstrated by the Ritter group.A procedure for trifluoromethylation of arenes via copper catalyzed C-H activation was optimized and used to produced and impressive scope of aryl trifluoromethanes using the TMGÁCF 3 I reagent.Examples of other transformations such as olefin and thiol trifluoromethylations, a-trifluoromethylation of silyl enol ethers, and trifluoromethyl addition to aldehydes could all be carried out using these stock solutions to generate products in competitive yields compared to the counterpart reaction using CF 3 I gas.Solutions of CF 3 I in TMG or DMSO, as well as the analogous C 2 F 5 I solutions, are currently commercially available or can be prepared using a Schlenk line manifold.However, it should be noted that DMSO is a potential ligand for transition metal such as palladium.For example, using the CH 3 I complex solution in transition metal-catalyzed reactions could be difficult because the DMSO might be competitive with the ancillary ligands and might affect the efficiency of the reactions.
These CF 3 I stock solution reagents will likely support future research on new transformations using this synthetic building block.One such example is the construction of trifluoromethylated cyclobutyl rings using DMSOÁCF 3 I by the Aggarwal group. 41hotochemically generated trifluoromethyl radical can react with the strained Sigma bond in a bicyclo[1.1.0]butane(BCB)-boronate complex, which in turn is formed from reaction with a sulfoxide  bearing the bicyclo[1.1.0]butanegroup and a boronate ester bearing the desired organic group (Fig. 21).This reaction yielded trifluoromethylated cyclobutyl rings bearing a boron ester and a variety of organic groups on the newly formed quaternary carbon with high diastereoselectivity.The method is compatible with many biologically relevant molecules and can be extended to a wide scope of other electron poor fluoroalkyl iodides beyond CF 3 I.The sulfoxide and boronate ester were first reacted with lithium tert-butoxide at À78 1C for 15 minutes.Addition of the DMSOÁCF 3 I and irradiation with blue LED lights for 1 hour yielded the final trifluoromethylated product.Mechanistic investigations suggested that the blue light promotes homolysis of the CF 3 I to generate the trifluoromethyl radical which attacks the strained Sigma bond of the (BCB)-boronate complex.The resulting radical species can then pass an electron to another molecule of CF 3 I propagating the chain reaction, leaving the now electron-deficient species to undergo a fast 1,2-metalate rearrangement to yield the product.
While photocatalysis has greatly increased the utility of CF 3 I gas, it can still be difficult to handle and accurately measure concentrations.Continuous flow chemistry can provide an alternative which allows accurate measurements, controlled delivery of CF 3 I via mass flow controllers, and superior gas-liquid mixing compared to batch experiments.
In 2014, the Noel and Hessel groups have collaboratively utilized CF 3 I gas in continuous flow to produce several classes of valuable trifluoromethylated products. 42Trifluoromethylation of five-membered heteroaryl rings was possible using 1-4 mol% of [Ru(bpy) 3 Cl 2 ] photocatalyst and TMEDA base (tetramethylethylenediamine) in acetonitrile under continuous flow conditions.Mass flow controllers accurately delivered 4 equivalents of CF 3 I gas under optimal conditions (Fig. 22), which could be varied to accommodate different substrates.The use of transparent PFA tubing allowed homogeneous photoirradiation of the reaction mixture, whereas this is a challenge in scaling up batch photochemical reactions due to absorption and limited penetration depth of light.The microreactor was placed in a beaker with blue light-emitting diode (LED) light strip coiled inside.After a residence time of 8 to 32 minutes, a variety of heteroarenes including pyrroles, indoles, furans and thiophenes, were trifluoromethylated in 55 to 95% yields.In this flow system, a BPR was not used and a Taylor flow regime resulted for gas-liquid mixing.The benefits of continuous flow conditions and the microreactor technology for this photochemical transformation, such as ease of scalability and catalyst loading optimization, were demonstrated.In less than 9 hours, a long durational flow reaction produced 1.98 g (9.5 mmol) of product G.It was possible to lower the catalyst loading to 0.05 mol% by extending the residence time to 32 minutes.
The mechanism of this transformation was further investigated in another report. 43The use of microreactor technology allowed for the precise determination of photon flux, quantum yield and reaction rate constants to help elucidate the mechanism.The consumption of CF 3 I gas in the Taylor flow regime directly changed the residence time of the reaction mixture in the flow reactor coil, and the residence time was used as a key factor in kinetic studies.As outlined in Fig. 22, the excited photocatalyst follows a reductive pathway, whereby it is first reduced by the TMEDA and passes this electron onto CF 3 I as supported by Stern-Volmer experiments.ncorporation of S-CF 3 groups into biologically active molecules is a growing area of research.Methods to synthesize aryl and alkyl S-CF 3 compounds have been developed by Wang, Noel and co-workers using batch and continuous flow protocols with a similar photocatalytic system and conditions as discussed above (Fig. 23). 44It was found that the rate of the batch reaction was dependent on the amount of mixing.By carrying out the reaction in continuous flow, a greater interfacial area between gas and liquid reagents was achieved, allowing for an acceleration of the reaction and significantly shortened reaction time.With a residence time of just 1 minute, it was possible to obtain trifluoromethylated products from (hetero)aryl and alkyl thiols in competitive or better yields compared with those of the batch protocol.The amount of CF 3 I gas required could also be reduced to from 4 to 1.1 equivalents by utilizing continuous flow conditions.
In a separate report, Noel and co-workers investigated trifluoromethylations of cysteine residues (Fig. 24). 45This class of thiols are particularly interesting since the trifluoromethylated derivatives may find use in a variety of peptide labeling applications.This trifluoromethylation of sulfur atoms for batch and continuous flow were also developed using Ru(bpy) 3 Cl 2 as the photocatalyst.Reactions performed in continuous flow were found to have increased efficiency and resulted in 10% more formation of product on average compared to the batch reactions.The reaction time was decreased from 2 hours in batch to 5 minutes (t R ) in continuous flow.
The active trifluoromethyl radical is proposed to be generated via photoexcitation of the photocatalyst followed by reductive quenching allowing to the reduced catalyst to transfer an electron to the CF 3 I gas.The trifluoromethyl radical then reacts with the thiol substrate to generate a trifluoromethylated thiol radical.Mechanistic investigations find evidence to support the presence of a chain propagating SET step where the thiol radical species transfers an electron to another molecule of CF 3 I to continue the reaction and generate the desired product (Fig. 24).
In 2016, conditions were reported by Noel and co-workers for the trifluoromethylation and hydrotrifluoromethylation of styrenes. 46These trifluoromethyl-containing products are useful in both pharmaceutical and materials synthesis due to the altered properties relative to their non-fluorinated counterparts.Although Ru(bpy) 3 Cl 2 was found to be a competent photocatalyst for many of the above transformations using CF 3 I, it was unable to provide satisfactory yields in the trifluoromethylation of styrenes.Suitable reaction conditions were found using fac-Ir(bpy) 3 as the photocatalyst in 0.5 mol% (Fig. 25), and trans-isomers of the products were primarily provided.Batch conditions for the transformation were also developed, but increased selectivity for the trans-isomers were observed in continuous flow.The trans-selectivity in continuous flow for this transformation was postulated to be due to the homogenous irradiation of the reaction medium and shorter irradiation period for the product molecules.The shortened irradiation time in flow resulted in the suppression of isomerization from trans-to cis-isomer via an energy transfer mechanism.In addition to trifluoromethylated styrenes, hydrotrifluoromethylated styrenes could also be produced by addition of 4-hydroxythiophenol (4-HTP) as a hydrogen atom donor and changing the reaction solvent (Fig. 25).The modularity to generate trifluoromethylated or hydrotrifluoromethylated styrene products accompanied by the ability to easily substitute other electron poor alkyl iodides to perform perfluoroalkyl reactions gives this methodology a clear advantage over other olefin trifluoromethylation procedures.g. 24 Photocatalyzed trifluoromethylation of cysteine residues in continuous flow. 45he proposed mechanism for both transformations is shown in Fig. 25.The iridium photocatalyst is first excited and transfers an electron to CF 3 I to produce the trifluoromethyl radical which can react with the styrene substrate.In the pathway leading to trifluoromethylation, the resulting radical species is then oxidized by the photocatalyst to form a carbocation intermediate to complete the photocatalytic cycle.Solvent adducts have been observed by GC-MS (gas chromatographymass spectrometry) to support the hypothesis that the radical and carbocation intermediates are stabilized by solvation.The carbocation then undergoes elimination to provide the product.In the hydrotrifluoromethylation pathway, the radical species instead reacts with the hydrogen atom donor to form the alkyl product.Radical thiol then donates an electron to the photocatalyst to close the cycle.

Chlorodifluoromethane
Chlorodifluoromethane (ClCF 2 H, as known as Freon 22 and HCFC-22) is a colorless gas and a potent ozone-depleting substance with a boiling point of À41 1C.It is a relatively cheap industrial chemical used to produce fluoropolymers and was widely used as a refrigerant.Under the Montreal Protocol, it has been mostly phased out for servicing refrigeration and airconditioning equipment in developed countries.However, exemptions were given for analytical, research and development purposes, including its use as a reaction feedstock. 47It is worth mentioning that ClCF 2 H, albeit being an attractive CF 2 source, has a GWP equal to 1810 and raises additional environmental concerns when used in organic synthesis.
Like fluoroform, deprotonation of the ClCF 2 H gas generates a chlorodifluoromethyl anion which rapidly undergoes a-elimination to give singlet difluorocarbenes which can be used in difluoromethylation reactions.
In 2017, the Kappe group disclosed the use of ClCF 2 H in the continuous flow synthesis of a key pharmaceutical intermediate I (Fig. 26) towards the preparation of eflornithine. 48The difluoromethylated malonate I bearing a nitrile group was prepared from commercially available malonate H, ClCF 2 H and easily accessible reagents under basic conditions.Upon reaction with bases such as NaOH or KOH, the ClCF 2 H can eliminate HCl to yield an electrophilic difluorocarbene, which then reacts with the anion of malonate H to give the difluoromethylated product.During optimization under batch conditions, the reactions gave moderate to good yields, but had poor selectivity and reproducibility.Further optimization of the transformation was then carried out in continuous flow.To prevent clogging caused by accumulation of inorganic solids (NaCl, KCl) as a result of a-elimination, a biphasic reaction medium using MeCN and aqueous NaOH was used to keep all components dissolved throughout the reaction.A microreactor plate with microstructures fabricated into the channels was used to increase mixing of the two immiscible phases.The organic phase containing the malonate and ClCF 2 H (condensed in MeCN) were injected into the microreactor in one stream and the basic aqueous phase was injected in a second stream.The use of a BPR (5 bar, 72.5 psi) enabled elevated temperatures up to 107 1C and kept the gas in solution.By harnessing the increased mixing and heat transfer of continuous flow, the rate of the productive reaction could be increased and allowed shorter reaction time to decrease the decomposition of ClCF 2 H. Optimal conditions were found to be 2.5 equivalents of ClCF 2 H, a concentration of 0.78 M of the malonate in MeCN for the organic phase and 8 M NaOH as the aqueous phase.The desired difluoromethylated product was obtained in 73% yield after a residence time of 24 minutes and the organic phase has a consistent high purity of 95% as determined by GC-FID (gas chromatography with flame-ionization detection).
Another procedure utilizing ClCF 2 H gas to form value-added products was reported by Fu and Jamison in the continuous flow synthesis of a-CF 2 D benzyl alcohols and gem-difluoroalkenes from aldehydes. 49Most previous methods used to form these products are considerably less atom economical than ClCF 2 H gas for the installation of the CF 2 H moiety. 10  As mentioned previously, CF 2 H groups are becoming more prominent in pharmaceuticals and other important compounds.Using this new procedure, CF 2 H groups can be installed efficiently as can the deuterated version (CF 2 D) which has been much less explored.As depicted in Fig. 27, the difluorocarbene is formed in solution through deprotonation of ClCF 2 H by LiOt-Bu followed by a-elimination of the chloride.The difluorocarbene can then react with triphenylphosphine to generate a phosphorus ylide.This ylide intermediate can then interact with the aldehyde substrate to form a difluoromethylated oxaphosphetane intermediate as shown in Fig. 27.NMR study suggests that it is at this stage that the phosphorus atom of the oxaphosphetane is more electrophilic than usual due to the electron-withdrawing CF 2 group, and can be hydrolyzed to give the a-CF 2 D benzyl alcohols and triphenylphosphine oxide.Alternatively, the oxaphosphetane can eliminate the triphenylphosphine oxide and gem-difluoroalkene product via a retro [2+2] cycloaddition under sufficient heating (100 1C).The ability of in-line generation and immediate consumption of an unstable species (oxaphosphetane), and the precise temperature control is highly advantageous and critical.Optimal conditions require three streams of reagents: the aldehyde substrate and triphenylphosphine in THF (2.0 equiv.),LiOt-Bu in THF (2.0 equiv.), and the ClCF 2 H gas (3.0 equiv., 1.32 sccm) (Fig. 28).These streams are mixed in a coil at 0 1C with a residence time of 11.9 minutes.At this point, the oxaphosphetane is formed and can either exit through a BPR (50 psi), introduced into a stream of water or D 2 O and reacted in a room temperature coil (t R = 3 min) or directly carried through to a heated coil (100 1C, t R = 4 min) depending on the desired product.Both procedures demonstrated a wide scope of reactivity and tolerance of many functional groups including hereroaryls, aryl halides, trifluoromethanes, ethers and vinyl halides.Both methods could be used for the production of derivatives of pharmaceutical compounds (adapalene, ataluren and probenecid).Advantages of continuous flow chemistry are also showcased here by the ability to use the ClCF 2 H gas directly with an MFC and super heat solvents to achieve optimal yields.In this work, only LiOt-Bu could be successfully used due to the generation of a soluble LiCl salt after a-elimination.Using KO-tBu or NaOt-Bu quickly generated insoluble inorganic salts, which clogged the tubings.The gem-difluoroalkenylation of aldehydes using ClCF 2 H gas under batch conditions was reported by Xiao in 2013 (Fig. 29). 50n their protocol, the ClCF 2 H gas was saturated in DMF to make a stock solution and a sealed tube was used for the reaction.To avoid the rapid generation of difluorocarbenes by using strong bases, an epoxide ring-opening approach was used to afford a low concentration of alkoxide anion for prolonged deprotonation of ClCF 2 H. n-BuNCl 4 was used in catalytic amount, and the 4 Å molecular sieve was both a drying agent and a Lewis acid to promote ring-opening of epoxide.A series of gem-difluoroalkenes was prepared in 49-92% yield after a 6 hour reaction at 110 1C.

Conclusion and outlook
The use of fluorinated greenhouse gases in fluoroalkylations has been made scalable, continuous, more efficient, environmentally friendly, safer, and easier to operate through translation to a continuous flow setting.We created this tutorial review article to highlight examples that would inspire chemists to exploit the ability of flow chemistry.Emphases have been given on the reactions' batch-to-flow transitions, experimental techniques used and some of our insights under flow-enabled conditions.Although flow chemistry, especially regarding gasliquid reactions, is usually used to optimize batch protocols by increasing control of reaction parameters or telescoping of multiple separate synthetic steps, we have shown some of the examples in this review article that flow techniques can indeed enable previously improbable reaction conditions.For example, the accurate delivery of gases by a mass flow controller and the small-scale generation-consumption of an unstable oxaphosphetane species led to the observation of new phosphorus chemistry and facile preparation of rare deuteriodifluoromethylated products.The in-line analysis techniques described in this review should be highly advantageous for discovery of new reaction mechanisms and could open up new chemical spaces.In particular, photochemical reactions using gases could benefit massively from flow technologies because of the limited mixing and penetration depth of irradiation under batch conditions, which caused longer reaction times, higher catalyst loadings or poor scalability.Finally, we envisioned that eventually many of the continuous flow systems created to transform the fluorinated greenhouse gases to value-added chemicals could be incorporated into greenhouse gas recycling facilities or waste management facilities in the fluorinated polymer production lines.Owing to the many unique advantages of flow chemistry including small system footprint, high reproducibility, scalability, system automations, improved safety, lowered cost and waste generation, we believe the continuous flow approaches will be highly applicable and feasible in industrial settings.
Born and raised in Canada, Preston MacQueen received his BSc (honours) in chemistry from Cape Breton University.He continued his chemistry education at Dalhousie University in the research group of Prof. Mark Stradiotto where he completed his PhD thesis focusing on nickel catalyzed C-N bond formation methodology.He was an NSERC Postdoctoral Fellow in Prof. Timothy F. Jamison's laboratory at Massachusetts Institute of Technology from 2018 to 2020.He is currently a process chemist at MilliporeSigma.Timothy F. Jamison Tim Jamison received his undergraduate education at UC Berkeley, where he conducted research in the laboratory of Prof. Henry Rapoport for nearly three years.Thereafter he was a Fulbright Scholar with Prof. Steven A. Benner at the ETH Zu ¨rich, carried out his PhD studies at Harvard University with Prof. Stuart L. Schreiber, and was a Damon Runyon-Walter Winchell postdoctoral fellow with Prof. Eric N. Jacobsen at Harvard University.He has been a member of the faculty at MIT since 1999, where he currently is the Robert R. Taylor Professor of Chemistry and Associate Provost.Wai Chung Fu Wai Chung received his BSc (honours) in chemistry from Hong Kong Baptist University and earned his PhD at The Hong Kong Polytechnic University (with Professor Fuk Yee Kwong).His graduate studies focused on the development of phosphine ligands and palladium-catalyzed cross-coupling reactions.Following a Croucher Postdoctoral Fellowship at MIT (with Professor Timothy F. Jamison), he returned to Hong Kong and became a research assistant professor at The Hong Kong Polytechnic University in 2020.His current research interests include transition metal catalysis, and the discovery and application of new chemical reactions in continuous flow.

Fig. 5 (
Fig. 5 (A) Illustration of Taylor flow.(B) Segmented flow afforded by mixing a solution and gas.The gas bubbles shrank, and the solution turned brown as the two phases reacted by Taylor recirculation.

Fig. 4 (
Fig.4(A) Equipment used in gas-liquid continuous flow reactions.(B) Tube-in-tube reactor used to saturate a flowing liquid with gas.13 Reprinted with permission from ref.13,Copyright 2015 American Chemical Society.

Fig. 7
Fig. 7 Ley's continuous flow trifluoromethylation of aldehydes with complete consumption of fluoroform. 22Reprinted with permission from ref. 22, Copyright 2018 American Chemical Society.

Fig. 26
Fig. 26 Telescoped continuous flow synthesis of key intermediate I towards the synthesis of eflornithine.48

Fig. 27
Fig.27Formation of difluoromethylated oxaphosphetene as a key intermediate towards the synthesis of a-CF 2 D benzyl alcohols and gemdifluoroalkenes.49