Large-scale production of CdO/Cd(OH)2 nanocomposites for non-enzyme sensing and supercapacitor applications

Recent advancements in electrode design are substantially linked to state-of-the-art nanomaterial fabrications. Herein, we report a simple one-pot hydrothermal synthesis of Cd(OH)2 with a platelet-like morphology, which was subsequently annealed at relatively high temperatures to produce a CdO/Cd(OH)2 nanocomposite for the first time. It was found that the control of thermal treatment allowed tunable charge transport across the nanometre scale due to the presence of CdO and Cd(OH)2 mixed nanocrystals. The CdO/Cd(OH)2 nanocrystals offer interesting prospects for the electrocatalytic oxidation of nitrite ions and for supercapacitor applications. The CdO/Cd(OH)2 nanocomposite was blended with a trace amount of gold NPs for enhancing the electrochemical conductivity and electrocatalytic capability for nitrite oxidation with a sensitivity of 32.9 μA mM−1. It afforded a promising electrocatalyst in a wide concentration range up to 10 mM with a low detection limit of 0.87 μM. Furthermore, the CdO/Cd(OH)2 nanocomposite electrode was showed to be a highly active and stable supercapacitor, achieving a high specific capacitance in an alkaline medium of about 145 F g−1 at a discharge current of 2.0 A g−1. These results have revealed that the presence of mixed oxide/hydroxide nanocrystals in nanoscale dimensions will be very interesting for various electrochemical applications and provide for a new class of nanodevices based on electrochemistry with unique capabilities.


Introduction
Transition metal oxide/hydroxide nanostructures are widely applied in a plethora of technologically signicant disciplines such as optoelectronic, 1 catalysis, 2 dye-sensitizer solar cell, 3 and sensor applications. 4,5 Because they provide a high surface area to volume ratio, hydrothermal stability, and various oxidation states, they possess unique optical, electronic, and magnetic properties. 6,7 Interestingly, the morphological-dependent interatomic bond distances, stoichiometry, and crystal defects have profound inuences on their functionality and applicability. 8 Therefore, considerable efforts have been exerted to control the intrinsic crystal arrangement and morphology of the nanomaterials to enable specic functionalities that are selected to align with the targeted applications. Among the various transition metal hydroxides, Cd(OH) 2 nanostructures have gained signicant interest because they can be potentially converted to CdO through dehydration or to other Cd-based functional materials (e.g. CdO, CdS, and CdSe) by appropriate reaction with other elements or compounds. 9 Cd(OH) 2 is a highly promising material for optoelectronic and other applications such as in solar cells, 10,11 phototransistors, 12 photodiodes, 13 transparent electrodes, cathode electrode of batteries, and gas sensors. 14 Various morphologies of Cd(OH) 2 , such as nanoplatelets, 9 nanorings 15 and nanowires, 16 have been reported recently. Despite this signicant progress, it is still a big challenge to align Cd-based nanostructures for various targeted applications.
Recently, the areas of electrochemistry (i.e. electrocatalysis, supercapacitors, batteries, fuel cells, solar cells and electroanalytical chemistry) have been greatly impacted by the availability of materials in nanoscale dimensions in term of their size, morphology, porosity and functionality, because they offer a short diffusion path and a favourable electrode/electrolyte contact area. These signicant benets can lead to the potential development of novel nanodevices with unique functionalities and processes. Therefore, the development of nanostructured electrodes is a very active and robust research area that is expected to provide next-generation technologies for environmental and food science analyses, improving and/or supplanting conventional sensing strategies. Although, nitrites are toxic inorganic contaminants, they have been widely used in meat curing, 17 food preservatives, 18 dyes, bleaches, fertilizers and in many medicinal purposes. 19 The nitrites in water and the atmosphere are essential precursors in the formation of carcinogenic nitrosamines in the stomach. 20 Signicantly, nitrites can oxidize haemoglobin to methaemoglobin, which is not capable of carrying oxygen; furthermore, the latter can reach toxic concentrations in a high density aquaculture system and as a result, the higher concentration of nitrites leads to considerable economic losses to aquaculture production. 21 The fatal dose of nitrite ingestion is reported to be between 8.7 mM and 28.3 mM and consequently the World Health Organization has mentioned that nitrites should have a guidance level of 3 mg L À1 (65 mM) for short-term exposure and a provisional guideline level of 0.2 mg L À1 (4.3 mM) for longterm exposure. 19 Therefore, the development of reliable, portable, sensitive and economical sensors for monitoring nitrites is highly recommended. 22 To realize the objective of nanostructured electrodes, different transition metal oxides nanostructures, such as RuO 2 , Fe 2 O 3 , Co 3 O 4 , NiO, MnO 2 , CuO, have been reported for highpower electrochemical supercapacitors. 23,24 Although the toxicity of cadmium-based materials is well known, Cd(OH) 2 has been widely used as an electrode material for cadmiumnickel batteries because of its high energy density, long lifetime, high discharge rates and relatively low cost. Cd(OH) 2 nanowires have been recently explored as low-cost alternative electrode materials for supercapacitors. Cd(OH) 2 nanowires synthesized by a chemical bath deposition method on a stainless-steel substrate yielded a specic capacitance of 46.15 F g À1 at 0.93 A g À1 . Thus, simplicity, exibility and efficient power performance are still the major challenges for the development of Cd(OH) 2 and/or CdO supercapacitors. In the present work, we built an advanced nanostructured electrode based on a CdO/ Cd(OH) 2 nanocomposite with a platelet-like morphology. First, Cd(OH) 2 nanoplatelets were synthesized via a simple and scalable hydrothermal protocol. Then, a subsequent lowtemperature annealing process was performed to reveal CdO/ Cd(OH) 2 mixed nanocrystals. To optimize the electrode performance and minimize the resistivity, a trace amount of citratecapped gold nanoparticles was added to the CdO/Cd(OH) 2 nanoplatelets dispersion. The nanocomposite suspension was then drop-cast on the surface of screen-printed electrodes (SPEs). Interestingly, the CdO/Cd(OH) 2 nanocomposite-modied SPEs represented mechanically robust, stable, portable, exible, low-cost and low-resistive nanostructured electrodes that exhibited promising electrocatalytic activity towards nitrite oxidation and for supercapacitor applications.

Chemicals
All the chemicals were of the highest analytical grade available and were used as received without further purication. Cadmium chloride (CdCl 2 ), ammonium hydroxide (NH 4 OH 28%), ethanol, disodium hydrogen phosphate (Na 2 HPO 4 ), potassium chloride (KCl), sodium sulfate (Na 2 SO 4 $6H 2 O), sodium nitrite (NaNO 2 ), sodium nitrate (NaNO 3 ), sodium iodide (NaI), sodium thiosulfate (Na 2 S 2 O 3 ), sodium acetate (CH 3 -COONa), boric acid and ascorbic acid were supplied from Sigma-Aldrich Co. Ltd. All the solutions were prepared using bi-distilled water with a resistivity of more than 18.2 MU cm. A 0.05 M Britton-Robinson buffer solution was prepared by mixing equimolar amounts of boric acid, citric acid and phosphoric acid solutions. The pH was adjusted by the addition of 1.0 M sodium hydroxide solution.

Synthesis of CdO nanostructures
Cd(OH) 2 nanoplatelets were fabricated via a hydrothermal route. First, 1.83 g of CdCl 2 was dissolved in 50 mL water and a measurable volume of NH 4 OH solution (28%) was added dropwise under magnetic stirring to adjust the pH to 9.5. Subsequently, the solution was transferred into a 100 mL Teon autoclave and heated at 160 C for 6.0 h. The obtained Cd(OH) 2 was washed several times with a mixture of deionized water and ethanol to remove the remaining agents and then dried at 60 C overnight. To obtain CdO/Cd(OH) 2 and CdO nanoplatelets, a subsequent annealing process was performed in air at 300 C and 400 C, respectively, for 3.0 h with a heating rate 2 C per minute ( Fig. S1 in ESI †).

Fabrication of the screen-printed electrodes
The SPEs were fabricated in-house with an appropriate stencil using a DEK 248 screen-printing machine (DEK, Weymouth, UK). These electrodes have been used extensively in previous studies. 5,8,[25][26][27] Here, rst, a carbon-graphite ink formulation (product code C2000802P2; Gwent Electronic Materials Ltd, UK) was screen-printed onto a polyester (Autostat, 250 mm thickness) exible lm (denoted throughout as standard-SPE). This layer was cured in a fan oven at 60 C for 30 min. Next, a silver/ silver chloride reference electrode was included by screenprinting Ag/AgCl paste (product code C2040308D2; Gwent Electronic Materials Ltd, UK) onto the polyester substrates and a second curing step was undertaken where the electrodes were cured at 60 C for 30 min. Finally, a dielectric paste (product code D2070423D5; Gwent Electronic Materials Ltd, UK) was then printed onto the polyester substrate to cover the connections. Aer a nal curing at 60 C for 30 min, these SPEs were ready to be used. These SPEs have been reported previously and shown to exhibit a heterogeneous electron transfer (HET) rate constant, k o , of ca. 10 À3 cm s À1 , as measured using the [Ru(NH 3 ) 6 ] 3+/2+ redox probe.

Fabrication of CdO/Cd(OH) 2 -nanocomposite-modied screen-printed electrodes
The SPE was modied with CdO/Cd(OH) 2 nanocomposite by a simple drop-cast process. A stock solution of CdO/Cd(OH) 2 nanocomposite was prepared by dissolving 10.0 mg of the CdO/ Cd(OH) 2 sample in 10.0 mL double distilled water and then 1.0 mL (0.3 mg) of citrate-capped gold nanoparticles was added and mixed well. The nanocomposite suspension was stored at 4 C. 28 A measured volume of CdO/Cd(OH) 2 /Au suspension was dropped onto the SPE surface and le to dry for 30 min in a desiccator. Then, the CdO-nanocomposite-modied screenprinted electrode was ready to use for further electrochemical experiments.

Water sample analysis
A sample of tap water was collected and its pH was adjusted by the addition of sulfuric acid solution (0.1 M). Then, differential pulse voltammetry (DPV) was performed on the solution and the responses recorded, while a standard addition method was utilized to determine the concentration of nitrite ions in the tap water.

Characterizations of the CdO/Cd(OH) 2 nanostructures
The morphology of Cd(OH) 2 samples before and aer thermal treatment were investigated using eld emission scanning electron microscopy (FE-SEM, JEOL model 6500). Before inserting the sample into the chamber, the powder was ground and xed onto a specimen stub using double-sided carbon tape. Then, a 10 nm Pt lm was coated via anion sputtering (Hitachi E-1030) at room temperature to obtain high-resolution micrographs. For better recording of the FE-SEM images, the SEM was operated at 15 keV.
Wide-angle powder X-ray diffraction (XRD) patterns were measured using an X-ray diffractometer (model FW 1700 series, Philips, Netherlands) with monochromated CuKa radiation (l ¼ 1.54Å), employing a scanning rate of 0.060 min À1 and 2q ranges from 4 to 60 . The diffraction data were analysed using the DIFRAC plus Evaluation Package (EVA) soware with the PDF-2 Release 2009.
The textural surface properties and pore-size distribution were determined by N 2 adsorption/desorption isotherms at 77 K with a BELSORP analyser (BEL Co., JP Ltd). The specic surface area (S BET ) was calculated using the Brunauer-Emmett-Teller (BET) method with multipoint adsorption data from the linear segment of the N 2 adsorption isotherm. The pore-size distribution was determined from analysis of the desorption branch of the isotherm using the nonlocal density functional theory (NLDFT). Furthermore, thermogravimetric analysis (TGA) was measured in a ow of nitrogen using TG-60 (Shimadzu Ltd, JP).
The electrochemical experiments were performed using an Autolab 302 N potentiostat/galvanostat workstation. All the measurements were conducted using a screen-printed electrode conguration. During the development of the protocol, the CdO/Cd(OH) 2 -nanocomposite-modied screen-printed electrode was used with a platinum counter electrode and Ag/AgCl/ KCl (sat) as the reference electrode. Connectors for the efficient connection of the screen-printed electrochemical sensors were purchased from Kanichi Research Services Ltd (UK). 25-28

Features of the CdO/Cd(OH) 2 nanocomposites
The formation of the CdO/Cd(OH) 2 nanoplatelets via a template-free mechanism mainly involved nucleation, growth and dehydroxylation steps. First, the addition of ammonium hydroxide to CdCl 2 solution generated small nuclei Cd(OH) 2 , which then subsequently dissolved in the presence of excess ammonia solution due to the formation of [Cd(NH 3 ) n ] 2+ ions. Under hydrothermal conditions, the solubility of the [Cd(NH 3 ) n ] 2+ complex is decreased due to the formation of NH 3 gas bubbles. These gas bubbles can be used as a template to guide developing small nuclei Cd(OH) 2 (k sp ¼ 7.2 Â 10 À15 ) and to grow Cd(OH) 2 with a hexagonal plate-like shape by an Ostwald ripening process. Finally, the dehydroxylation of asprepared Cd(OH) 2 under mild thermal treatment at 300 C led to formation of CdO/Cd(OH) 2 mixed nanocrystals with a platelet-like morphology. However, CaO nanoplatelets were produced aer thermal treatment at 400 C, as shown in the TG analysis (Fig. S1 †). Furthermore, it was noted that no precipitate was formed without the addition of ammonium hydroxide solution. When replacing NH 4 OH by NaOH solution, Cd(OH) 2 plates with an irregular shape were obtained. When increasing the solution pH to 12.0, no change in morphology or in the size of the plate was observed (Fig. S2 †). Fig. 1 shows the scanning electron microscopy (SEM) images of the as-synthesised Cd(OH) 2 sample before and aer thermal treatment at 300 C. The Cd(OH) 2 had a hexagonal platelet-like morphology, which was maintained even aer thermal treatment. It was found that the dehydroxylation of Cd(OH) 2 at 300 C did not change the morphology or size. The as-synthesised Cd(OH) 2 and CdO/ Cd(OH) 2 particles had nano-sized dimensions and smooth ne surfaces with an average diameter of 200-300 nm and a thickness of about 30 nm. The SEM micrographs showed that the simple synthesis procedures could efficiently control the shape and size of Cd(OH) 2 and CdO in condensed orientation sequences (as shown in Fig. S2 †).
To identify the crystal structure of cadmium-based materials before and aer thermal treatment, wide-angle X-ray diffraction (XRD) was performed. Fig. 2 shows the XRD patterns of the asprepared Cd(OH) 2  . This result indicated that the monoclinic nanocrystals of Cd(OH) 2 were converted to the cubic (Fm3m) symmetry of CdO nanocrystals aer thermal annealing at a relatively high temperature, which agreed with the conversion of nonconductive monoclinic crystals of La 2 Mo 2 O 9 to a highly conductive cubic form aer thermal treatment at 580 C. 29 Thus, the produced CdO/Cd(OH) 2 nanoplatelets composite via the dehydroxylation of Cd(OH) 2 at 300 C might be very interesting for various electrochemical applications.
The textural properties of the CdO/Cd(OH) 2 nanoplatelets were investigated by N 2 adsorption/desorption isotherms (Fig. 2B). The CdO/Cd(OH) 2 nanocomposite showed a type II isotherm without any hysteresis loops, indicating the formation of macropore cavities between the nanoplatelets. The CdO/ Cd(OH) 2 nanocomposite exhibited a low specic surface area of S BET ¼ 15.07 m 2 g À1 with a macropore distribution of 145 nm. The porous network texture of CdO/Cd(OH) 2 is very important for designing electrochemical-based devices because it provides an enhanced surface area and alters the mass transport characteristics.
To determine the surface functional groups of Cd-based materials before and aer thermal treatments, FTIR spectra were collected, with the results shown in Fig. 2C. The CdO/ Cd(OH) 2 nanoparticles show absorption bands below 1000 cm À1 , corresponding to Cd-O and Cd-O-H stretching vibrations, which conrm the formation of CdO and CdO/ Cd(OH) 2 nanoparticles aer thermal treatment at 400 C and 300 C, respectively. Whereas, the band at 3530 cm À1 is attributed to the stretching vibration of the hydroxyl group, indicating the presence of residual water and hydroxyl groups in the CdO nanoparticles. The absorption bands at 1400 cm À1 can be attributed to N-H stretching. The FTIR investigations claried that the cadmium oxide particles involve a trace amount of Cd(OH) 2 nanocrystals as well as containing N-H bond intercalates within the oxide phase. 16 With increasing the thermal temperature, the absorption bands at 3526, 1400 and 856 cm À1 were signicantly decreased due to the formation of CdO nanocrystals.

Electrochemical sensing of nitrites on CdO/Cd(OH) 2 nanocomposites
3.2.1. Voltammetric behaviour of nitrite ions. Unfortunately, the electrochemical oxidation of nitrites on the bare electrodes caused accumulative electrode-passivation/fouling effects, which greatly limited the analytical performance of the electrodes. 30 Thus, chemically modied electrodes have attracted great attention in the last decades. Fig. 3 shows the  cyclic voltammetry (CV) responses of 1.0 mM sodium nitrite in 0.1 M sodium sulfate Na 2 SO 4 at pH 4 on unmodied/bare SPEs, Au-SPEs, Cd(OH) 2 /Au-SPEs, CdO/Cd(OH) 2 /Au-SPEs and CdO/ Au-SPEs at a scan rate of 0.05 V s À1 . No noticeable reduction peak can be observed, indicating that the electro-oxidation of nitrite ions on the cadmium oxide composite-modied screenprinted electrode is irreversible in nature. Although citratecapped gold nanoparticle shi the oxidation peak of nitrites to a more negative potential, the peak current does not change compared to bare SPEs, and a new oxidation peak appears, which was attributed to the oxidation of gold nanoparticles assembled on the SPEs. The Cd(OH) 2 /Au-SPEs, CdO/Cd(OH) 2 / Au-SPE and CdO/Au-SPE showed enhanced peak current for nitrite oxidation with a positive potential shi of about 140, 10 and 40 mV vs. Ag/AgCl, respectively. The positive potential shi of Cd(OH) 2 was higher than for the CdO material, despite them having almost the same size and platelet-like morphology. Thus, the cubic crystal CdO nanocrystals have a higher electrocatalytic activity than monoclinic Cd(OH) 2 nanocrystals due to the conductivity-structure relationship via a disorder in the oxygen sublattice. 29 Furthermore, the presence of Cd(OH) 2 nanocrystals in the CdO nanoplatelets is very important to enhance the electrochemical performance and electrocatalytic activity of cadmium oxide nanoplatelets.
To nd out the best electrochemical response of the CdO/ Cd(OH) 2 nanocomposite for the electrochemical determination of nitrites, the effects of the supporting electrolytes, the solution pH and the mass loading of composite material on the SPEs were explored. Fig. S3 † shows the cyclic voltammetry response of 0.5 mM nitrite on CdO nanocomposite-SPE in the presence of 0.1 M various supporting electrolytes, namely sodium sulfate, sodium hydrogen phosphate and potassium chloride, at a scan rate 50 mV s À1 . It was found that the anodic peak current of nitrite was enhanced in the presence of 0.1 M sodium sulfate as a supporting electrolyte (Fig. S4 †). Furthermore, the voltammetric response towards the electrochemical oxidation of nitrite was also investigated on the CdO nanocomposite-SPE in nitrite solutions of differing pHs (Fig. S5 †). The pH of 0.1 M sodium sulfate was adjusted by adding a few drops of sulfuric acid and sodium hydroxide to reach the required pH value. Analysis of the voltammetric peak current, I p , as a function of pH is described in Fig. S5b. † It was found that the voltammetric peak current was increased up to pH 4 due to the instability and protonation of nitrite ions at a very low pH. Meanwhile, the peak current does not change at higher pH values, indicating that the electrocatalytic oxidation of nitrite is proton independent. Thus, pH 4 was selected as a suitable pH value to determine nitrite ions in water samples. Furthermore, the voltammetric peak potential, E p , was shied to less positive values with increasing the pH of the nitrite solution. This result revealed the participation of protons in the electrochemical oxidation process of nitrites. Beyond pH 4, the peak potential was insensitive to pH, which is consistent with the reported pK a for nitrous acid between 3.2 and 3.4. Also observed was a linear  response of the peak potential from the oxidation of nitrite at pH lower than 4 with a slope of 55 mV per pH. This value is very close to the Nernstian slope (59 mV per pH at 298 K) for a process that involves the transfer of an equal number of protons and electrons in an electrochemical process. The mass loading of CdO nanocomposites onto SPEs was also studied (Fig. S6 †). It was obvious that 5.0 mg of CdO nanocomposites on SPE was sufficient for the electrocatalytic oxidation of nitrite solution. Thus, a 0.1 M Na 2 SO 4 solution at pH 4 and 5.0 mg of CdO nanocomposite-SPEs were used in the further voltammetric experiments of the nitrite sensing.
The cyclic voltammetric experiments were performed at pH 4 over a range of scan rates from 25 to 200 mV s À1 , as shown in Fig. 4. The voltammetric current signal-scan rate dependence for all scan rates was observed; whereby, upon increasing the scan rate, the current magnitude increases, where the peak current is proportional linearly to the square root of the scan rate; I p /mA ¼ 52.0n 1/2 /V 1/2 s À1/2 + 7.13 mA. This result suggested that the oxidation of nitrite on the CdO nanocomposite-SPEs is controlled by a mass transfer process. The linear relation of the logarithm of the anodic peak current and the logarithm of the scan rate revealed a slope of 0.4, which is close to 0.5, indicating that there was no adsorption of nitrite molecules on the CdO nanocomposite-SPEs (Fig. S7a †). That there was no reverse reduction wave of nitrite and the positive shi in the oxidation peak potential conrmed the irreversible nature of the electrode processes. For a totally irreversible diffusion-controlled process, the analysis of the peak potential against the scan rate showed a linear segment (Fig. S7b †) with a slope of 0.095. By applying the following equation: where E p is the peak potential, n is the scan rate, K is a constant, a is the charge transfer coefficient, R is a gas constant, T is the temperature -298 K, F is the Faraday constant and n is the number of electrons consumed in the electrochemical reaction. For a one electron transfer process, the electron transfer coef-cient was 0.68, indicating that the oxidation of nitrite on the CdO composite electrode is limited by a mass transfer process. Furthermore, the decrease in the current function (I/n 1/2 ) with increasing the scan rate revealed that the electrochemical  oxidation mechanism of nitrite on the CdO-composite-modied SPE is likely to be via an EC mechanism, as follows: Electroanalytical sensing of nitrite ions. Next, attention was turned to exploring the electroanalytical performance of the CdO nanocomposite-SPEs towards nitrite detection. Fig. 5a shows the cyclic voltammetric curves resulting from the additions of nitrite concentrations over the range 5.0 mM to 10 mM into the supporting electrolyte of 0.1 M Na 2 SO 4 at pH 4 at a scan rate of 50 mV s À1 . A signicant enhancement of the oxidation peak current upon nitrite additions was observed, where linear responses were shown over the range of 5.0 mM to 1.0 mM: I p /mA ¼ 32.86C nitrite /mM + 6.07 mA; R 2 ¼ 0.99, and 1.0 mM to 10.0 mM: I p /mA ¼ 6.06C nitrite /mM + 24.64 mA; R 2 ¼ 0.991. Based on the rst linear range, the limit of detection (3S/ N) was found to be 0.87 mM.
The selectivity of CdO nanocomposite-SPE towards nitrite determination was evaluated in the presence of some potential interferants, such as sodium acetate, ascorbic acid, boric acid, potassium chloride, potassium iodide, sodium nitrate and sodium phosphate. The CV curves were recorded in solution at pH 4 in the presence of 100 mM nitrite and 100 mM of each interferant. The voltammetric peak height of the nitrite was changed by only about AE3.6% of its original value. Furthermore, the relative standard deviation was 1.18% for ve repetitive measurements of 100 mM nitrite ions. Five separately CdO nanocomposite-SPEs were also measured in the presence of 100 mM nitrite ions, where the relative standard deviation was about 3.13%. These results indicated that the CdO nanocomposite-SPE exhibited a high electrocatalytic capability and stability towards the oxidation of nitrites even in the presence of various interferants. Furthermore, the differential pulse voltammetry (DPV) responses were also explored to increase the sensitivity of the analytical performance of the CdO nanocomposite-SPEs towards nitrite determination. Fig. 6 shows the typical DPV responses for successive additions of nitrites over the range of 5.0-630 mM in 0.1 M of sodium sulfate at pH 4 on the CdO nanocomposite-SPE. Along with increases in the nitrite concentrations, the voltammetric peak currents were linearly enhanced over the range 5.0-150.0 mM: I p /mA ¼ 0.011C nitrite /mM + 7.3 mA; R 2 ¼ 0.985, and for 200-630 mM: I p /mA ¼ 0.004C nitrite / mM + 8.37 mA; R 2 ¼ 0.98. The limit of detection (3S/N) was deduced to be 0.8 mM, according to the rst linear range. Such analytical performance of CdO nanocomposite-SPEs enable the determination of nitrite ions in a wide concentration range with a low detection limit compared to the previously reported literature (Table 1). This could be suitable for short-term exposure detection as described by the World Health Organisation (WHO). 19 Furthermore, CdO nanocomposite-SPEs offer interesting features, such as low cost, easy construction and storage, a potential for miniaturization and a facility of automation and the construction of simple and portable equipment.

Detection of nitrites in a tap water sample.
To verify the potential application of the CdO composite-modied screen-printed electrode, it was applied for the determination of nitrite in a tap water sample. The DPV responses were explored in a tap water sample aer adjusting the pH of the water to 4.0 by adding drops of 0.1 M sulfuric acid. It was found that no voltammetric peak was observed because the concentration of nitrite was below the detection limit capabilities. Consequently, a recovery experiment was performed on the tap water sample. The sample was spiked with different concentrations of nitrites in the range of 20 to 400 mM with a standard addition protocol performed in triplicate (Fig. S8 †). It was observed that a recovery of 90 (AE3)% was possible, indicating that the CdO composite-modied screen-printed electrode is a promising electrode material for the determination of nitrite in water samples.

Electrochemical performance of the CdO composite for energy storage
Cadmium hydroxide has been used as a promising electrode material for cadmium-nickel batteries for several decades due to its high energy density, long lifetime and high discharge rates. However, there are also a few literature reports considering Cd-based materials in supercapacitor applications, as shown in Table 2. Based on the large specic area of randomly stacked CdO/Cd(OH) 2 nanoplatelets and their unique electrocatalytic capability through the presence of bi-nanocrystals of CdO/Cd(OH) 2 , it was expected that the CdO nanocomposite electrode would exhibit a high performance for energy storage supercapacitors. With a three-electrode conguration, the CdO nanocomposite-SPE as a working electrode, Pt as the counter electrode and Ag/AgCl as the reference electrode, then, the pseudocapacitive performance of CdO nanocomposite-SPE was improved. Cyclic voltammetry and galvanostatic chargedischarge measurements were carried out in 1.0 M NaOH with a three-electrode system at room temperature (Fig. 7). It can be seen that the CV curve exhibits several redox peaks, indicating that the capacitance is mainly governed by the pseudocapacitor behaviour based on the redox process, as following: 31 CdO + H 2 O + OH À + e À 4 Cd(OH) 3 À Cd(OH) 3 À + OH À + e À 4 Cd(OH) 4

2À
The effect of scan rate on the CdO composite electrode was investigated in 0.1 M NaOH in the range from 0.01 to 0.15 V s À1 . It is observed that the current density increases gradually, while the shape of the cyclic voltammetry curves remain unchanged with increasing scan rates. This result indicates the good pseudocapacitive behaviour of the CdO composite-SPE with a high rate capability. The specic capacitance of the CdO nanocomposite electrode was calculated from CV curves at different scan rates, as following: where C s is the specic capacitance in F g À1 , m is the mass of active material in grams, n is the potential scan rate in V s À1 , DV is the working potential window and iVdV is the integration area under the CV curve. The specic capacitance was calculated to be 253. 28, 255.06, 229.65, 204.47, 191.48 F g À1 at potential scan rates of 0.01, 0.025, 0.05, 0.1, 0.15 V s À1 , respectively. It was obvious that the specic capacitance was decreased with increasing the potential scan rate. Interestingly, the specic capacitance of the CdO nanocomposite-SPE was decreased about 13% with a ten-fold increase in the scan rate. This result indicates the high capability rate and applicability of the simply synthesized CdO nanocomposite compared to the previously reported supercapacitor based on CdO and/or Cd(OH) 2 nanostructures, in which the specic capacitance decreases signicantly with increasing the potential scan rate. 16,[39][40][41][42] To further estimate the specic capacitance (C s ) and to comprehend the rate capability, galvanostatic charge-discharge measurements were performed within the potential window 0.0 to À1.0 V, at different current densities in 1.0 M NaOH, and the results are presented in Fig. 7b. The specic capacitance was measured by galvanostatic charge-discharge curves using the following equation: where C s is the specic capacitance, I is the current response, t is the discharge time, m is the mass of electroactive material and DV is the working potential window. The specic capacitance was found to be 145.45 F g À1 at a current density of 2.0 A g À1 . It was found that the specic capacitance, C s , was signicantly enhanced more than two-times over the value reported for one-dimensional cadmium hydroxide nanowires 16 and other reported Cd-based materials ( Table 2). The specic capacitance was reduced with increasing the current density, which might due to the shorter diffusion path to reach the active sites of the cadmium oxide nanocomposite as well as the decit of the faradic redox reaction at a higher current density. Noticeably, the specic capacitance remained as high as 87.02 F g À1 , even when the discharge current density was increased to 8 A g À1 . These results showed satisfactory long-term stability and a high specic capacitance due to their unique internal crystal structure (Fig. 8). As shown in Fig. 8, there is continuous galvanostatic charge-discharge cycling at a constant current density of 2 A g À1 over 1000 cycles. The CdO nanocomposite showed long-term stability compared with that previously reported (Table 2), although the specic capacitance lost about 7% in the rst 200 cycles and then no further change was observed over the following 800 cycles. To the best of our knowledge, this interesting pseudocapacitive behaviour is rarely observed in Cd-based materials, which might be attributed to the presence of mixed nanocrystals of Cd(OH) 2 in CdO nanoplatelets which offer a short diffusion path, fast electron/ ion transfer and better stress/strain accommodation, which enhance its electrochemical performance.

Conclusions
The simple and large-scale production of hexagonal CdO/ Cd(OH) 2 nanocomposites with a platelet-like morphology was achieved through a partial thermal treatment of Cd(OH) 2 platelets at 300 C. Interestingly, the CdO/Cd(OH) 2 -SPEs showed high electrocatalytic activity towards nitrite oxidation over a wide concentration range with a lower micromolar detection limit achievable at pH 4 and formed a stable, high capability supercapacitor electrode in 0.1 M NaOH solution.
The results suggested that the presence of Cd(OH) 2 nanocrystals in the CdO nanoplatelets showed enhanced electrochemical performance with high stability, which might open new avenues in the fabrication of nanodevices based on electrochemistry with unique capabilities.

Conflicts of interest
There are no conicts to declare.