Continuous direct anodic flow oxidation of aromatic hydrocarbons to benzyl amides †

Methods for the site-selective C–H functionalisation of hydrocarbons, without the need of installing an additional functional group, are becoming more widely used. Their exploitation in multistep synthesis allows reducing the number of steps, increases atom efficiency and reduces waste. Nevertheless, most of the modern C–H activation methods, although being usually chemoand regioselective, require expensive and moistureor air sensitive transition metal catalysts. Electrochemical methods for direct oxidation and reduction are increasingly important for modern synthetic chemistry mainly because they employ electric current instead of more obnoxious agents. Electrochemistry is therefore becoming more frequently used in the design of new atom-efficient, safe and more sustainable chemical processes. Also a range of products can sometimes be obtained from a common starting material by controlling either the electric current or potential. Carrying out electrochemical experiments in a continuous manner increases greatly their throughput and general applicability. A higher surface-to-volume ratio, characteristic for microand mesofluidic conditions, causes better conductivity of the reaction media, resulting in a lower concentration of the ancillary electrolyte required. Furthermore, a shorter distance between the anode and cathode enables the processes which involve highly unstable, reactive intermediates to proceed smoothly and with high level of selectivity due to fast subsequent chemical reactions. It has previously been shown that replacing batch electrolysis with the continuous methods can reduce the formation of the overoxidation products since the reactor is constantly replenished with the starting materials and the desired products are removed to a benign environment. The discovery reported here relates to the development of an electrochemical method to convert aromatic hydrocarbons into the benzyl amides. It is well known that alcohols can be converted into amides by the Ritter reaction – when reacting with nitriles and water under strong acidic conditions. This reaction proceeds through the formation of a carbocation which is sequentially trapped first by nitrile followed by a molecule of water. If instead the carbocation is generated by two-electron oxidation from the hydrocarbon, following the same trapping steps, the amide can be obtained analogously. This reaction has been observed when toluene and a few electron-rich toluene derivatives were oxidized electrochemically at the anode in batch mode using acetonitrile as a solvent and an undivided cell. Unfortunately, these amides could only be isolated in low yields mainly due to overoxidation. Considering that flow electrochemistry methods are often advantageous over the batch alternatives in terms of synthetic applicability, efficiency and throughput, we focused on the development of a continuous direct anodic oxidation of aromatic hydrocarbons to benzyl amides. All the experimental studies were performed using an Ammonite® 8 reactor (V = 1 mL) equipped with a platinum disk anode, circular stainless steel cathode, and perfluoroelastomer FFKM gasket. This unit, with the carbon polymer anode, was previously applied to the electrochemical methoxylation of N-formylpyrrolidine and p-methoxybenzyl alcohol deprotection allowing high conversion of the substrate in a single run. The reaction conditions for the continuous electrolysis at the constant current of p-tert-butyltoluene 1a in acetonitrile (0.1 M) as a model substrate were explored varying

Methods for the site-selective C-H functionalisation of hydrocarbons, without the need of installing an additional functional group, are becoming more widely used. 1 Their exploitation in multistep synthesis allows reducing the number of steps, increases atom efficiency and reduces waste. 2 Nevertheless, most of the modern C-H activation methods, although being usually chemo-and regioselective, require expensive and moisture-or air sensitive transition metal catalysts. 3lectrochemical methods for direct oxidation and reduction are increasingly important for modern synthetic chemistry mainly because they employ electric current instead of more obnoxious agents. 4Electrochemistry is therefore becoming more frequently used in the design of new atom-efficient, safe and more sustainable chemical processes. 5Also a range of products can sometimes be obtained from a common starting material by controlling either the electric current or potential. 6arrying out electrochemical experiments in a continuous manner increases greatly their throughput and general applicability. 7A higher surface-to-volume ratio, characteristic for micro-and mesofluidic conditions, causes better conductivity of the reaction media, resulting in a lower concentration of the ancillary electrolyte required. 8Furthermore, a shorter distance between the anode and cathode enables the processes which involve highly unstable, reactive intermediates to proceed smoothly and with high level of selectivity due to fast subsequent chemical reactions. 9It has previously been shown that replacing batch electrolysis with the continuous methods can reduce the formation of the overoxidation products since the reactor is constantly replenished with the starting materials and the desired products are removed to a benign environment.7d The discovery reported here relates to the development of an electrochemical method to convert aromatic hydrocarbons into the benzyl amides.It is well known that alcohols can be converted into amides by the Ritter reactionwhen reacting with nitriles and water under strong acidic conditions. 10This reaction proceeds through the formation of a carbocation which is sequentially trapped first by nitrile followed by a molecule of water.If instead the carbocation is generated by two-electron oxidation from the hydrocarbon, following the same trapping steps, the amide can be obtained analogously.This reaction has been observed when toluene and a few electron-rich toluene derivatives were oxidized electrochemically at the anode in batch mode using acetonitrile as a solvent and an undivided cell. 11Unfortunately, these amides could only be isolated in low yields mainly due to overoxidation.11a Considering that flow electrochemistry methods are often advantageous over the batch alternatives in terms of synthetic applicability, efficiency and throughput, we focused on the development of a continuous direct anodic oxidation of aromatic hydrocarbons to benzyl amides.
All the experimental studies were performed using an Am-monite® 8 reactor (V = 1 mL) 12 equipped with a platinum disk anode, circular stainless steel cathode, and perfluoroelastomer FFKM gasket.This unit, with the carbon polymer anode, was previously applied to the electrochemical methoxylation of N-formylpyrrolidine and p-methoxybenzyl alcohol deprotection allowing high conversion of the substrate in a single run. 13he reaction conditions for the continuous electrolysis at the constant current of p-tert-butyltoluene 1a in acetonitrile (0.1 M) as a model substrate were explored varying electrolyte, electric current and the concentration of water (Table 1). 13irst, the efficiency of LiBF 4 as an electrolyte was examined.It was shown that the presence of water was crucial for the reaction, since without water added only small amount of the product was detected (entry 1, Table 1).Stoichiometric amounts of water were found to be optimal as an excess led to a decrease in conversion to 3a (entries 2 and 4, Table 1).Similarly, the use of stoichiometric amount of LiBF 4 also provided the highest conversion to 3a (compare entries 5 and 6 with entry 3, Table 1).The lower conversion to 3a was observed at a higher current due to over-oxidation with the ptert-butylbenzaldehyde formation (determined by 1 H NMR in the crude reaction mixture) while some of the starting material 1a was still present (entry 7, Table 1). 14nder the optimum conditions when using LiBF 4 as an electrolyte (entry 3, Table 1), it was found that the system was not stable over time and that the conversion towards the amide 3a deteriorated significantly (from 66% to 38% in 3 hours).The formation of an inorganic solid inside the cell channel was observed over the time that caused clogging and voltage instability.This solid, which reacted violently with water with the formation of hydrogen gas, is likely to contain lithium metal in agreement with the previous reports.11c Subsequent loss of the current efficiency was therefore the most probable reason for the decreased conversion over time.
In order to find sustainable alternative conditions, the anodic oxidation of p-tert-butyltoluene 1a was optimised using an electroneutral electrolyte Bu 4 NPF 6 (entries 8-13, Table 1).As in the case of LiBF 4 , a stoichiometric amount of water was found to be optimal for the experiments with Bu 4 NPF 6 (entries 8-11, Table 1) providing the highest conversion to the desired product 3a (48% conversion; entry 9, Table 1).Applying higher current did not improve the conversion due to the overoxidation side reactions (entries 12 and 13, Table 1).Under these new conditions, the system remained stable and fully homogeneous over time.
One possible reason of the higher efficiency of the system based on the LiBF 4 electrolyte during the initial period, when compared to Bu 4 NPF 6 , could be the difference in the pH of the two reaction mixtures (Scheme 1).
In the case of LiBF 4 , the lithium cation Li + is initially readily reduced at the cathode not affecting the pH of the reaction mixture (red rectangle, Scheme 1).On the other hand, the anodic oxidation produces 1 eq. of H + per 1 F of electric current passed, resulting in an acidic pH of the reaction mixture as confirmed experimentally (pH ∼ 0-1).Conversely, when Bu 4 NPF 6 is used as an electrolyte, as 1 eq. of H + per 1 F of electric current passed is produced in the same way at the anode, 1 eq. of H + per 1 F is consumed at the cathode, maintaining the overall neutral pH of the reaction mixture (green rectangle, Scheme 1).Knowing that the reduction potential EĲ2H + /H 2 ) at the cathode is proportional to lnĲ[H + ]) according to the Nernst equation, the reduction of H + to H 2 and the overall electrolysis should proceed easier and at a lower voltage in the presence of a Brønsted acid.With this information available, the influence of various Brønsted acid additives on the anodic oxidation of p-tertbutyltoluene 1a was explored (Table 2).
The continuous flow electrolysis could not be performed in pure acetonitrile as a solvent and toluenesulfonic acid (pKa = −2.8)as an additive due to a solid formation (entry 1, Table 2).The addition of dichloromethane as a co-solvent (25% vol) was beneficial to keep the system homogeneous, but the amide 3a was still obtained with low conversion (48% conversion; entry 2, Table 2).When using trifluoroacetic acid (TFA; pKa = 0.23), a higher conversion to 3a was observed (68% conversion; entry 3, Table 2).This result could be further improved by using methanesulfonic acid (MSA; pKa = −1.9;72% conversion; entry 4, Table 2).Changing the concentration of MSA did not lead to any further improvement in the formation of 3a (entries 5 and 6, Table 2).Under the optimised conditions (entry 4, Table 2) the system remained fully homogeneous over the time.
An online steady state monitoring was best achieved by means of a UV/vis detector (Flow-UV™) 15 which was installed after the reactor (Fig. 1).The reaction pleasingly proceeded with the constant productivity of the amide 3a equal to 0.38 g h −1 over 9 hours (Fig. 1).
Once the stability and the applicability of the developed procedure to a large scale production were demonstrated, the generality of the methodology over a range of aromatic hydrocarbons was studied (Scheme 2).To simplify the downstreaming process, the efflux of the reactor was mixed with a second stream (500 μL min −1 ) containing an ammonia solution in methanol (0.7 M).Full neutralisation of the acid was beneficial to reduce decomposition of the amide prod-ucts 3 under strong acidic conditions.The evaporation of solvent in vacuo was sufficient to obtain the crude products 3 (Scheme 2).

Conclusions
In conclusion, the preparation of benzyl amides from a number of aromatic hydrocarbons was achieved by a stable and continuous flow anodic oxidation.The addition of a Brønsted acid was crucial to maintain the process stability over 9 hours with the productivity of 9.12 g per day.The results described here open up to the application of electrochemical methodologies to large-scale production.

Table 2
Anodic oxidation of p-tert-butyltoluene 1a in acetonitrile (0.1 M) using Bu 4 NPF 6 as an electrolyte and Brønsted acid additives a