Jump to main content
Jump to site search

Issue 3, 2014
Previous Article Next Article

One-pot two-step mechanochemical synthesis: ligand and complex preparation without isolating intermediates

Author affiliations


Although the use of ball milling to induce reactions between solids (mechanochemical synthesis) can provide lower-waste routes to chemical products by avoiding solvent during the reaction, there are further potential advantages in using one-pot multistep syntheses to avoid the use of bulk solvents for the purification of intermediates. We report here two-step syntheses involving formation of salen-type ligands from diamines and hydroxyaldehydes followed directly by reactions with metal salts to provide the corresponding metal complexes. Five salen-type ligands 2,2′-[1,2-ethanediylbis[(E)-nitrilomethylidyne]]bis-phenol, ‘salenH2’, 1; 2,2′-[(±)-1,2-cyclohexanediylbis-[(E)-nitrilomethylidyne]]bis-phenol, 2; 2,2′-[1,2-phenylenebis(nitrilomethylidyne)]-bis-phenol, ‘salphenH23; 2-[[(2-aminophenyl)imino]methyl]-phenol, 4; 2,2′-[(±)-1,2-cyclohexanediylbis[(E)-nitrilomethylidyne]]-bis[4,6-bis(1,1-dimethylethyl)]-phenol, ‘Jacobsen ligand’, 5) were found to form readily in a shaker-type ball mill at 0.5 to 3 g scale from their corresponding diamine and aldehyde precursors. Although in some cases both starting materials were liquids, ball milling was still necessary to drive those reactions to completion because precipitation of the product and or intermediates rapidly gave in thick pastes which could not be stirred conventionally. The only ligand which required the addition of solvent was the Jacobsen ligand 5 which required 1.75 mol equivalents of methanol to go to completion. Ligands 1–5 were thus obtained directly in 30–60 minutes in their hydrated forms, due to the presence of water by-product, as free-flowing yellow powders which could be dried by heating to give analytically pure products. The one-armed salphen ligand 4 could also be obtained selectively by changing the reaction stoichiometry to 1 : 1. SalenH21 was explored for the one-pot two-step synthesis of metal complexes. In particular, after in situ formation of the ligand by ball milling, metal salts (ZnO, Ni(OAc)2·4H2O or Cu(OAc)2·H2O) were added directly to the jar and milling continued for a further 30 minutes. Small amounts of methanol (0.4–1.1 mol equivalents) were needed for these reactions to run to completion. The corresponding metal complexes [M(salen)] (M = Zn, 6; Ni, 7; or Cu, 8) were thus obtained quantitatively after 30 minutes in hydrated form, and could be heated briefly to give analytically pure dehydrated products. The all-at-once ‘tandem’ synthesis of [Zn(salen)] 6 was also explored by milling ZnO, ethylene diamine and salicylaldehyde together in the appropriate mole ratio for 60 minutes. This approach also gave the target complex selectively with no solvent needing to be added. Overall, these syntheses were found to be highly efficient in terms of time and the in avoidance of bulk solvent both during the reaction and for the isolation of intermediates. The work demonstrates the applicability of mechanochemical synthesis to one-pot multi-step strategies.

Graphical abstract: One-pot two-step mechanochemical synthesis: ligand and complex preparation without isolating intermediates

Back to tab navigation

Supplementary files

Article information

16 Oct 2013
05 Dec 2013
First published
12 Dec 2013

Green Chem., 2014,16, 1374-1382
Article type

One-pot two-step mechanochemical synthesis: ligand and complex preparation without isolating intermediates

M. Ferguson, N. Giri, X. Huang, D. Apperley and S. L. James, Green Chem., 2014, 16, 1374
DOI: 10.1039/C3GC42141D

Social activity

Search articles by author