Emmanuel
Canales
a,
Samuel C.
Hower
a,
Daniel Paul
Li
a,
Aditya
Tambe
a,
David
Rothamer
b and
George W.
Huber
a
aDepartment of Chemical and Biological Engineering, University of Wisconsin-Madison, USA. E-mail: gwhuber@wisc.edu
bDepartment of Mechanical Engineering, University of Wisconsin-Madison, USA
First published on 9th May 2024
Ethanol can be converted into diesel fuel ethers using a three-step catalytic approach that involves ethanol oligomerization to larger alcohols, hydrogenolysis of the esters followed by dehydration of the C4 to C8 alcohols into ethers. In this paper we report results for the dehydration of a mixture of C4–C8 alcohols using a zeolite Y catalyst in a continuous flow reactor. Mono-molecular dehydration of the alcohols produces olefins while bi-molecular dehydration of the alcohol produces ethers. Increasing the pressure increases the ether selectivity while decreasing the pressure produces more olefins. Linear alcohol feeds produce more C8+ ethers, while branched and secondary alcohols lead to more olefins. Olefin and coke selectivities increase with increasing carbon chain length of alcohols. Secondary alcohols lead to higher coke selectivities. Ethanol/butanol oligomerization experiments showed that the incoming dehydration feedstock can be grown to larger C6+ alcohol fractions, leading to higher yields of C10+ diesel-range ethers.
We have previously proposed a three-step process to convert ethanol into distillate-range ethers as outlined in Scheme 1.2 The process first involves ethanol oligomerization to C4+ oxygenates which is rich in alcohols over a Cu/MgxAlyO catalyst.10 This process creates a distribution of oxygenate molecules consisting of C4+ alcohols, aldehydes, ketones, and esters. The second step is an ester hydrogenolysis step that hydrogenates esters in this oxygenate stream into alcohols. The products from the hydrogenolysis reactor are a mixture of C4+ linear, branched, and secondary alcohols. The last step is dehydration which produces C8+ ethers and C4+ olefins. Mono-molecular dehydration produces olefins while bimolecular dehydration produces ethers. These ethers possess higher cetane number than diesel fuel. The ethers also have the appropriate boiling point and low volatility suggesting they can be used in diesel blends.11 C10+ ethers also have lower sooting index, water solubility and higher flashpoint temperatures compared to lower chain ethers.12 Ethers produced from C6+ alcohol streams have similar properties relative to diesel #2. While butyl ether may be used as a diesel additive, blending limits can be influenced based on the minimum flashpoint requirement for a diesel #2 blend (>52 °C), as shown in Fig. SI1.†
The objective of this paper is to study the catalytic dehydration of mixtures of ethanol oligomerization products over a zeolite Y catalyst in a continuous flow reactor. We try to understand how the reaction conditions and different feed components influence the product selectivity, catalytic activity, and catalytic deactivation for dehydration reactions. Over 100 different products are produced during ethanol oligomerization including linear, branched and secondary C4–10 alcohols, aldehydes, ketones, and esters with the primary products being linear alcohols.10Fig. 1 (ref. 1 and 2) shows the simulated Guerbet (SG) feedstocks that we will use for etherification in this publication. The SG feed assumes that all the products lighter than C4 from ethanol oligomerization are distillated and the ketones, aldehydes and acetals are hydrogenated to their respective alcohols. The product selectivity for ethanol oligomerization is a function of conversion.10Fig. 1 shows the SG product selectivity at four different ethanol conversions from ethanol oligomerization.2 (e.g. SG-12 represents the simulated Guerbet product from ethanol oligomerization at 12% ethanol conversion and assuming the ketones, aldehydes and acetals are hydrogenated to their respective alcohols).
Fig. 1 Oxygenate distribution of products from ethanol oligomerization as a function of ethanol conversion. These products will be used as feeds for the etherification experiments in this paper. The conversion was varied by changing the weight hourly space velocity in the reactor. The conversion is shown after the dash. (a) represents the linear alcohol distribution and (b) represents the branched and secondary alcohol distributions, as well as the ester distributions. For secondary alcohols, the numbering is defined by ‘n + 1’. Colors not visibly shown for compounds are present in low amounts (<1.0%). Data taken from ref. 1 and 2. |
The final SG mixtures are a distribution of linear alcohols, branched alcohols, secondary alcohols, and esters. The left-hand side of the graph represents the mol fractions of linear alcohols, while the right-hand axis represents the mol fractions of secondary and branched alcohols, in addition to esters. At an ethanol conversion of 12%, n-butanol is the main product, with low amounts of C6+ alcohols and esters. As the ethanol conversion increases, the size of the alcohols produced increases. The secondary and branched alcohol content and the ester content increase with increasing conversion as well.
In this study, we demonstrate how dehydration of ethanol oligomerization products produces distillate range ethers with selectivities ranging from 60% to 80% in a continuous flow reactor with zeolite HY. We also demonstrate the ability to tune reactant feedstock distributions, which allows for tuning the final average carbon number of the fuel mixtures produced. The oxygenate products are feedstocks that have varying size distributions depending on the ethanol conversion in the first step (10% to 69%), as shown in Fig. 1. A more detailed breakdown of feedstock compositions used in this paper can be seen in the ESI (see Tables SI1–4 in ESI Section 1†). For more information on the detailed composition of the final dehydration products, refer to Tables SI5–SI14 in ESI Section 2.†
(1) |
(2) |
(3) |
(4) |
(5) |
(6) |
(7) |
(8) |
Fig. 2 shows the Gibbs free energy as a function of temperature for liquid phase dehydration of 2-butanol and 1-butanol. Thermodynamic data was taken from the NIST database, and the model was implemented using UNIFAC parameters in ASPEN. The reactor pressure was 100 psig, and a temperature range from 50–400 °C was modeled. The Gibbs free energy trends were then fit to a polynomial to highlight the trends on the graph.
Fig. 2a shows the etherification products for 1-butanol. The free energy formation of ethers of varying linear alcohol feed chain sizes are similar across a wide temperature range, suggesting that bimolecular dehydration is independent of the size of the alcohols in the reaction streams. Both monomolecular and bimolecular dehydration are thermodynamically favorable reactions at temperatures from 50 to 300 °C. As the temperature increases, mono-dehydration becomes more favorable than bimolecular dehydration. The Gibbs free energy is also a function of the alcohol structure. Linear ethers are lower in Gibbs free energy compared to ethers formed from a secondary alcohol.
Fig. 2b represents the etherification products of 2-butanol, a secondary alcohol. Monomolecular dehydration of 2-butanol produces 2-butene. Bimolecular dehydration of 2-butanol produces sec-butyl ether. Bimolecular dehydration of 2-butanol with hexanol further produces hexyl-sec butyl ether. At temperatures below 200 °C, the ethers are the thermodynamically favored product. At higher temperatures olefins are the thermodynamically favored product. However, both monomolecular and bimolecular dehydration are thermodynamically favorable at temperatures from 50 to 300 °C. The free energy of formation of hexyl-sec butyl ether and sec butyl ether is similar.
Fig. 3 shows the dehydration reactions of pure alcohol feeds in a continuous flow reactor. All experiments were done at a constant WHSV. The carbon conversion increases with increasing chain length of the alcohol. The carbon balance decreases with increasing alcohol size as the larger alcohols produce more coke (see Tables SI5, SI6 and SI15†). The ether selectivity decreases, and the olefin selectivity increases with increasing carbon length of the alcohol. Based on these findings, a C10 alcohol such as 1-decanol would have a coke selectivity around 20%. These results suggest that it would be desirable to remove the C10+ alcohols from the feed prior to the etherification step. In all pure alcohol feed runs, the catalyst was shown to be stable for over 40 h TOS, as shown in Fig. SI6 and SI12.†
Fig. 3 Dehydration of pure alcohol over zeolite HY. T = 170 °C, P = 100 psig, 0.02 mL min−1 flowrate, WHSV = 0.54 h−1, TOS > 20 h. |
Feedstocks with the code ‘MG’ represent model Guerbet alcohol mixtures that assume all esters from the ethanol oligomerization reactor are broken down to their parent alcohols via ester hydrogenolysis. Fig. 4 shows the effects of esters on the dehydration step using MG-12 with different levels of esters. The difference between MG-12 and SG-12 is the presence of esters. SG-12 has an ester content of 1.46 wt%. Another feedstock with 0.15 wt% esters is shown in Fig. 4 and represents a feedstock with a significant reduction of esters in the reaction stream (see Table SI3†). The presence of esters in the reaction stream increases coke selectivity. It has been shown in the literature that esters of varying structure can play a significant role in coking selectivities over acid catalysts.14 As the ester concentration decreases, the ether selectivity and carbon balances increase. Small amounts of esters significantly decrease the carbon balance (see Tables SI7 and SI9†).
As the ester content in the feed increases the heavy oligomer concentration in the product increases. These heavy oligomers are soluble in the alcohol feed. These heavy oligomers have been studied and detected in similar systems, particularly for acid-catalyzed dehydration reactions of sugars from biomass.15,16 Fig. SI3† further supports this theory, as the amount of undetected carbon linearly increases with increasing ester concentration. For a more detailed breakdown of coke in the solid and liquid phase, refer to Tables SI8 and SI10.†
Therefore, as much of the esters as possible must be removed from the dehydration reactor stream. Ideally, the total alcohol purity of the reactant stream should be above 99.90 wt% to ensure that esters will not significantly change the reaction chemistry (refer to Tables SI1 and SI2† for feedstock comparison with MG-12 and SG-12). We conclude that an ester hydrogenolysis step is necessary to produce alcohol rich feedstocks for dehydration. Over zeolites, esters can create side reactions with the reactants and products produced in the dehydration step. Water produced from etherification can catalyze ester hydrolysis reactions. Over zeolites, as the ester is broken down to its respective alcohol and carboxylic acid, both molecules will compete for dehydration sites as shown by Corma and coworkers.17 The adsorption of carboxylic acids is stronger than for alcohols. Thus, the carboxylic acids likely cause a decrease in the number of acid sites that are available for dehydration reactions. Other labs have reportedly seen other adsorption effects over large-pore zeolite catalysts, in which upgrading incoming low-chain esters may be difficult. In the case of benzyl alcohol reacting with acetic acid over H-beta, increasing alcohol concentration led to a decrease in ester selectivity and an increase in ether selectivity.18 This is attributed to alcohols saturating the catalyst surface, blocking acid sites for carboxylic acids to react with other alcohol chains to produce esters.
Esters can be reduced using metals on various supports.19–21 The esters typically undergo three different reaction pathways which involve (1) CO bond hydrogenation to produce ethers and water, (2) C–O hydrogenolysis to produce alcohols and aldehydes (and further hydrogenation of the aldehydes to an alcohol) and (3) hydrolysis reactions which produce alcohols, alkenes, and carboxylic acids. In ethanol oligomerization, the esters produced typically fall within the carbon chain length of 8 and under. This makes pathway 1 undesirable, as it would mainly produce C8 ethers. Pathway 3 is also undesirable as carboxylic acids compete with alcohols for acid sites, decreasing dehydration rates. Pathway 2 is desirable in our applications, as only alcohols and aldehydes are produced. Under an H2 environment, the remaining aldehydes can be hydrogenated to their respective alcohol, leading to a pure alcohol feedstock that can be fed into the dehydration reactor. As previously mentioned, high ester conversion to alcohols will be necessary to minimize the effects of these molecules in the dehydration stream. As shown by Chavarrio,22 high ester conversion into alcohols can be achieved using Cu/ZrO2 catalysts (∼90% conversion). The Cu/ZrO2 catalyst simultaneously reduces the ester and hydrogenates the corresponding aldehyde. The use of these catalysts were tested with simulated Guerbet feedstocks by Restrepo-Flórez and coworkers,23 in which the ester mol fraction was decreased from 7.6–0.3%, resulting in a reduction of ∼96% of the ester molar composition. This reduction in ester content led to an increase in the final alcohol mol composition from 92.3–99.3%. Thus it is possible to reduce the ester content prior to the dehydration stream using a Cu/ZrO2 catalyst to produce highly concentrated alcohol streams above 99.96 mol%, or above 99.90 wt%.
The alcohol distribution of MG-12 is shown in Fig. SI1,† and a detailed breakdown of the feedstock studied can be found in Table SI2.† The effect of pressure on dehydration was studied with n-butanol and MG-12 feeds as shown in Fig. 5. Fig. 5a depicts the carbon number distributions for the ethers and olefins. The left-hand side depicts the selectivities of the ethers based on carbon number, while the right-hand side depicts the selectivities of the olefins based on carbon number. In all cases, the olefin selectivity was lower than the ether selectivity. Fig. 5b depicts that increasing the pressure does not affect the conversion or carbon balances with the butanol and MG-12 feeds. In all cases, the unknown products were below 10% selectivity. For pure n-butanol, pressure had minimal impact on the product distributions. The ether selectivity slightly increases, and the olefin selectivity slightly decreases with pressure for n-butanol (Fig. 5a). For n-butanol at 0 psig, the true coke selectivity based on TOC experiments is 3.5% (see Table SI8†). In Fig. 5b, the coke selectivity is zero as the carbon balances were over 100% when only the gas and liquid phase were analyzed. This is because the final mass balances obtained from the HPLC pump were over 100% when only gas and liquid products were considered. A noticeable pressure effect is observed with MG-12 (see Tables SI7 and SI8†). One plausible explanation is that pressurizing the system above the reactant vapor pressures shifts the reaction phase from gas to liquid (see Table SI11†). Due to the significant change in selectivities, all further reactions were conducted at 100 psig.
Rorrer and Eagan reported that alcohol structure is important in etherification, in which high linear alcohol streams increase the rate of etherification.11,13 However, the feeds they used were single alcohol feeds, linear alcohol-only mixtures, or binary reaction mixtures of linear and branched alcohols. While branched alcohols can still undergo etherification to some extent, secondary alcohols will mainly produce olefins. It is therefore unclear how complex C4+ alcohol distributions affect the final size and selectivities for ether and olefin distributions obtained from competitive dehydration reactions. Other groups have studied etherification of alcohols over polymeric acidic resin catalysts (i.e. Amberlyst 70), though these catalysts typically suffer from swelling due to water being formed during dehydration reactions, and thus catalyst stability further becomes an issue at temperatures above 150 °C.11,25–28 H-exchanged zeolites are robust catalysts that are not affected by swelling, though dealumination may be important in high water content streams and/or at reaction temperatures above 170 °C.29,30 The recent advancements in understanding the effects of water on zeolite structure suggest that these materials will be of interest for future processes that require water-tolerant catalysts for dehydration reactions.31
Fig. 1 depicts the molecular distribution of four different feedstocks obtained from an ethanol oligomerization reactor.1 As the ethanol conversion increases, larger fractions of branched and secondary molecules are present in the reaction stream. The ester composition further increases with increasing ethanol conversion. As shown in Scheme 1, all the esters are assumed to undergo 100% hydrogenolysis conversion to produce alcohol-rich streams. The alcohol-rich feedstocks are then used for the dehydration step to produce diesel-range ethers and olefin fuel precursors. These alcohol-rich streams are depicted in Fig. SI2,† and a detailed breakdown can be found in Table SI2.† Some alcohols were substituted for a commercially available alcohol because those alcohols could not be purchased commercially. For example, 2-ethyl-1-hexanol (C8) was used in place of C10+ branched alcohols (2-ethyl-1-octanol, 2-ethyl-1-decanol, and 2-ethyl-1-dodecanol). For secondary alcohols, C15+ secondary alcohols (were 4-undecanol, 4-tridecanol, 2-pentadecanol, and 2-heptadecanol) were replaced with 2-undecanol (C11). The lumping method was used to maintain the structural composition of linear, branched, and secondary alcohols.
Fig. 6 is the product selectivity, conversion and carbon balance obtained from the four model feedstocks studied with Tables SI12 and SI13† showing more details. Fig. 6a shows that as the linear alcohol content of the feed decreases the C8+ ether selectivity decreases. The olefin selectivity increases as the branched and secondary alcohol content of the feed increases. As shown by the C10+ ether selectivities, feedstocks with larger fractions of C6+ alcohols shift the ether selectivity from C8+ to C10+ ethers. The increase in C6+ alcohol content also shifts the olefin selectivity from C4+ to C6+ olefins. The unknown carbon detected increases with increasing complexity of the feedstock. Fig. 6b shows that the carbon balance decreases with increasing ethanol conversion. This effect is likely due to an increase in the C6+ alcohol content, branched alcohols, and secondary alcohols of the feed.
Both MG-67 and MG-69 have similar branched alcohol content (7.4 mol% vs. 6.9 mol%, respectively). However, the secondary alcohol content is 7 mol% higher for MG-69. The increase in secondary alcohol content led to an increase in coke selectivity on the catalyst surface by about 4% (see Table SI13†). While larger chain alcohols are present in MG-69, the linear alcohol distribution is similar (see Table SI2,† L/B and L/S ratios). Thus, secondary alcohols can lead to higher surface coke selectivities. While branched alcohols can still undergo bi-molecular dehydration to some extent, secondary alcohols are less likely to produce ethers and mainly undergo mono-dehydration. Secondary alcohols may either be adsorbing strongly over HY, or the olefins produced are possibly undergoing side reactions (i.e. acid-catalyzed oligomerization), leading to a decrease in the carbon balance via coking mechanisms.32,33 The olefins produced from branched alcohols can also undergo the same side reactions that secondary alcohol derived olefins encounter, though reactivity differences to coke products are still unclear. We conclude that secondary alcohols will likely not undergo etherification at our current conditions, with olefins the main by-products from secondary alcohols. The increase in secondary alcohol content led to an increase in the overall coke selectivity by about 1.5%. Further increasing the secondary alcohol content will lead to higher coke selectivities (see Table SI12†). The increase in secondary alcohol content can lower the final blend stock yields, as well as increase the CO2 emissions produced from coke removal through catalyst regeneration. Measuring the amount of carbon on the catalyst after reaction was done using total organic carbon content (TOC) analysis (see Table SI16†). The catalyst bed of MG-69 had a higher coke content than MG-67.
As shown in Fig. 7a, the size of the ethers does not increase from feedstock MG-12 to MG-44 likely because the n-butanol content in both feedstocks was similar (91.8 vs. 82.20 mol%, respectively). However, the ether size increases from 9.0 to 11.3 with feedstock MG-67. MG-67 has lower n-butanol content (67.88 mol%), while also having higher fractions C6+ linear and branched alcohols. The ether size decrease to 10.5 with feedstock MG-69 likely due to the higher fractions of secondary alcohols. Fig. 7b shows the ether and olefin selectivities as a function of the alcohol linearity of the feedstock. The ether selectivity decreases with decreasing linear alcohol fraction in the feed. This trend is consistent with other studies.11,13 As the fraction of linear alcohols continues to decrease, coking and mono-dehydration reactions become more prominent. We conclude that high linear alcohol streams above 80 mol% are needed to maintain the C8+ ether selectivity above 60%.
Our research team has shown that the C10+ ethers can be maximized by feeding in a mixture of ethanol and butanol into the Guerbet reactor.23Fig. 8 shows the products from the Guerbet reaction for MG-12, MG-67 and ethanol/butanol (EtOH/ButOH) oligomerization. These feeds were then used for the dehydration reaction. A detailed breakdown of the EtOH/ButOH oligomerization feedstock can be found in Table SI4.† MG-12 was chosen as it has the lowest selectivity to C10+ ethers, while MG-67 was chosen as it has the highest selectivity to C10+ ethers. The EtOH/ButOH oligomerization step assumes that un-reacted n-butanol from the process can be separated and recycled back into the ethanol oligomerization step. Recycling of n-butanol increases the overall C6+ alcohol content from the Guerbet feed. However, the linear alcohol content decreases when the butanol is recycled. The increase in branched alcohol content is expected due to the addition of n-butanol to the oligomerization step, as nucleophilic alcohols that are larger than ethanol react to form larger branched products.11,34 The secondary alcohol content slightly increases with butanol addition compared to MG-67. The alcohols from the feeds in Fig. 8 were then used for dehydration. Tables SI13 and SI14† show the detailed dehydration products from MG-12, MG-67 and the EtOH/ButOH oligomerization products. The carbon balances are lower for the EtOH/ButOH products at WHSV = 0.54 h−1, as well as the overall ether selectivity. The WHSV was doubled to assess the effects on carbon balance. Table SI14† shows that doubling the space velocity has a negligible effect on the carbon balances and slightly increasing the C10+ ether selectivity. While higher WHSVs lead to higher selectivities, the conversion further decreases. Here, determining the quality of the raw blends produced from an economic point of view should be assessed by engine testing. The supported engine testing can then help provide a sensitivity analysis on whether the slight increases in carbon balances produce better raw blends, while minimizing the amount of recycled reactant materials. This kind of analysis has been shown by Restrepo-Flórez and coworkers,2 where surrogate blends were tested, and the information was feed into a techno-economic analysis to understand the economic factors of the ethanol to diesel route.
As shown in Fig. 9a, the C10+ ether selectivity obtained from MG-67 is 50%, while the C10+ ether selectivity is 56% using the EtOH/ButOH product stream. As shown with the linear alcohol feeds, larger alcohols can lead to lower carbon balances and lower overall ether selectivity. This may explain why the selectivity only increased by less than 10% across the two feedstocks. Fig. 9b shows the ether and olefin yields. The C10+ ether yield increases because of the presence of larger fractions of C6+ alcohols from MG-12 to MG-67 (11% vs. 32%). The EtOH/ButOH oligomerization products further support that while stronger alcohol adsorption effects may be present, larger fractions of C6+ alcohols increase the C10+ ether yield. The C10+ ether yield for MG-67 was 32%, while for the dehydration of EtOH/ButOH oligomerization products the C10+ ether yield was 40%. Furthermore, the butyl ether yield was lower for the dehydration of EtOH/ButOH oligomerization products compared to MG-67 (4% vs. 14%). The implementation of an n-butanol recycling unit can therefore be used to significantly reduce the production of C8 ethers and shift the final product carbon number to the C10+ range. Because EtOH/ButOH oligomerization products were used to represent a recycle feed stream of n-butanol, it is therefore possible to further increase the C10+ ether yields while re-using unconverted alcohol in the dehydration steps.
The coke content on the catalyst was measured after using the MG-12, MG-67 and EtOH/ButOH feeds. The graphs for these experiments can be found in Fig. SI4.† In all cases, the presence of both soft coke and hard coke is observed on all beds. Volatile compounds are within the temperature region of 50–200 °C. The soft coke region is in the temperature range of 200–400 °C, while the hard coke region is in the temperature range of 400–600 °C.35 In all cases when oxygen is present, the largest change in weight occurs within the volatile and soft coke region. In the nitrogen experiments, there is minimal change in weight between the region of 400–600 °C. In all cases, the lowest mass change is in the hard coke region. This trend is also observed when analyzing the EtOH/ButOH oligomerization beds, in which most of the weight loss is in the volatile compound region.
Scheme 2 Proposed process diagram of ethanol to diesel fuel range ethers. Important design parameters are represented by dashed lines. Red line signifies the proposed n-butanol recycling unit and is not considered in the final mass balance. Fuel yields and mass outputs are shown on a dry ethanol basis. The hydrogen balance is based on an ethanol oligomerization reactor operating at 325 °C and 300 psig, with a partial pressure ratio of 4:1 for H2:ethanol. Most of the hydrogen is recycled, therefore low amounts of hydrogen is further added into the system. The daily bio-ethanol production is based on the production of approximately 60 MMgal per year of anhydrous ethanol. Data and overall process diagram is derived from ref. 2. |
Our approach to produce diesel range products outlined in this paper is the highest yield diesel fuel from ethanol technology reported in the literature. Several other approaches produce gasoline range products or jet fuel mixed with gasoline. For example a single stage ethanol to jet, using a zeolite catalyst, produces around 40–70 C% aromatics.3 In this approach, 30–60 C% may be used for distillate fuel applications, and the mixture may only be blended in low amounts unless the aromatics are distilled.3 Using a two-stage ethanol to jet fuel process, the maximum fuel yield can be around 65–70 C%.3
Footnote |
† Electronic supplementary information (ESI) available. See DOI: https://doi.org/10.1039/d4se00362d |
This journal is © The Royal Society of Chemistry 2024 |